Page 1
Xpelair Typical Specification
Xpelair Premier DX180, DX200 & CF20
he unit is to be supplied from the Xpelair
T
remier range by Applied Energy Products Ltd,
P
orley Way, Peterborough PE2 9JJ
M
el. +44 (0)1733 456789
T
Model Ref
X180* 91181AW
D
DX180T* 91182AW
X180H* 91183AW
D
DX200 91013AW
X200T 91014AW
D
CF20 91015AW
F20T 91016AW
C
*IPX4 rated
The unit shall be designed for flush or
•
urface mounting in walls, ceilings or through
s
lass (using the GMK kit) supplied
g
complete with fixing clamps for flush
mounting
CF20 models shall be supplied with
•
utside grille
o
• DX200 models shall have selectable speed
unning facility with speed selection at
r
nstallation
i
• DX200T shall have an adjustable overrun
timer (30s - 20min) with 2min start delay
CF20 shall have automatic operation through
•
ntegral humidity sensor, manual boost speed
i
ia pullcord and trickle ventilation
v
• CF20T shall have automatic operation
hrough integral humidity sensor, manual
t
oost speed via pullcord and trickle
b
entilation. Adjustable overrun timer
v
(30s - 20min). Optional 2 min start delay.
It shall be possible to remotely select
•
peeds using Xpelair switch
s
• The unit shall be BEAB approved and rated
at IPX5. The fan shall conform to Building
egulations for use in toilets, bathrooms and
R
tility rooms. The fan shall incorporate an
u
utomatic air operated backdraught shutter
a
ef. 90108AW
R
The unit shall be suitable for zone 1 and
•
one 2 requirements as defined by IEE
z
iring Regulations 16th Edition BS 7674:2001
W
• A rectangular cut out section shall be
provided in the top of the fan housing to
connect to Xpelair Profile kit
The housing and stylish air inlet shall be
•
oulded in high gloss white ABS
m
• The front cover shall be held in position
y the retaining clips to facilitate removal
b
nd adjustment
a
• The motor shall be totally enclosed, fitted
with sealed self aligning maintenance free
bearings and include thermal overload
protection
Dimensions shall be W x H x D
•
22 x 252 x 118mm excluding spigot
2
Ref. 90547AA
Xpelair Premier LoVolt LVDX200 & LVCF20
he unit is to be supplied from the Xpelair
T
Premier range by Applied Energy Products Ltd,
Morley Way, Peterborough PE2 9JJ
Tel. +44 (0)1733 456789
Model Ref
LVDX200 91453AW
LVDX200T 91040AW
LVCF20 91041AW
LVCF20T 91042AW
• The unit shall be 12V Safety Extra Low
Voltage with a separate SELV transformer
• The unit shall be designed for surface or
flush mounting using the fixing clamps
provided, in walls, ceilings or mounting
through glass using the GMK kit
The fan shall incorporate an air operated
•
backdraught shutter.
Xpelair Premier L
The unit is to be supplied from the Premier
UltraDC range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ Tel.
+44 (0) 1733 456789
VCF20T DC
Model Ref
Premier LVCF20T DC 92288AW
• A rectangular cut out section shall be
• LVCF20 models shall be supplied with an
• LVDX200 shall be operated by a proprietary
• LVDX200T shall have an adjustable overrun
• LVCF20 shall have automatic operation
• LVCF20T shall have automatic operation
•
• The unit shall be fitted with an UltraDC low
• The unit shall be suitable for use in the splash
provided to connect to Xpelair Profile 29
flatduct using Xpelair kit
outside grille
remote switch or sensor
timer (30sec-20mins) with 2 min start delay
through integral humidity sensor, manual
boost speed via pullcord and trickle
ventilation
through integral humidity sensor, manual
boost speed via pullcord and trickle
ventilation. Adjustable overrun timer
(30sec-20min). 2 min start delay
The unit shall be suitable for use as an
intermittent fan in bathrooms and WCs or as
a decentralised continuous extract unit for
kitchens, utility rooms, bathrooms and WCs
in accordance with the requirements of
Building Regulations Part L1
energy external rotor motor with maintenance
free greased for life bearings
zone of a bath or shower identified as Zone 1
in the IEE regulations 16th edition. A separate
SELV transformer shall be supplied with the
unit which shall be installed outside of Splash
zones 1 and 2
Ref. 90547AA
• The unit shall be BEAB approved and
rated at IPX5. The fan shall
conform to Building Regulations for
use in toilets, bathrooms and utility rooms
• The unit shall be suitable for zone 1 and
zone 2 requirements as defined by IEE
Wiring Regulations 16th Edition BS
7674:2001
• The housing and stylish air inlet shall be
moulded in high gloss white ABS
• The front cover shall be held in position
by the retaining clips to facilitate removal
and adjustment
• The motor shall be maintenance free,
totally enclosed, fitted with sealed self
aligning bearings and thermal overload
protection
• Dimensions shall be W x H x D
222 x 252 x 118mm excluding spigot
The unit shall be rated at IPX5
•
The fan shall be designed for flush or surface
•
mounting on walls or ceiling and shall be
fitted with an automatic air operated
backdraught shutter
• The housing and air inlet fascia shall be
moulded in high gloss ABS
• The front cover shall be held in position by
two retaining clips to facilitate removal
Dimensions:
W x L x H
222 x 252 x 118 excluding spigot
160
Page 2
Xpelair Premier CF20/40T CV
The unit is to be supplied from the Premier
UltraCV range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ Tel.
+44 (0) 1733 456789
Model Ref
CF20/40T UltraCV 92293AW
The unit shall feature UltraEC technology
•
educing energy use and providing longer
r
motor life
• The motor shall be of external rotor
construction with sealed, maintenance free
earings and include safety thermal
b
verload protection
o
A choice of installation performances shall be
•
available to meet the installed performance
requirements of Building Regulations Part F1intermittent ventilation in Kitchens, Utility
rooms, Bathrooms and Sanitary
ccommodation; Humidity controlled
a
Xpelair Profile 29
The components are to be supplied from the
Xpelair Profile 29 range by Applied Energy
Products Ltd. Morley Way, Peterborough PE2
9JJ Tel. +44 (0)1733 456789
Model Ref
Premier flat ducting adaptor 90547AA
Straight duct 2m 91106AA
Horizontal 45 bend 91109AA
Horizontal 90 bend 91108AA
Vertical 45 bend 91111AA
Vertical 90 bend 91110AA
Round to rectangular adaptor 91113AA
intermittent ventilation with manual override in
Kitchens and Bathrooms and continuous
ecentralised ventilation in Kitchens, Utility
d
ooms, Bathrooms and Sanitary
r
ccommodation
a
Performance shall be set by the installer by
•
way of installer accessible dip switches
• For internal rooms, the Timer when selected
hall be factory set at 15 minutes in
s
ccordance with Part F1 but shall be installer
a
djustable up to 20 minutes (minimum period
a
hall be 20 seconds)
s
• There shall be a 'Quick visit' timer feature
preventing nuisance tripping if the room is
occupied for less than 2 minutes
The fan shall have a constant volume feature
•
hich maintains the chosen performance
w
rrespective system pressure up to 100Pa
i
The unit shall be designed for flush or surface
•
mounting in walls or ceilings using the
accessories provided
Model Ref
Elbow bend/plenum 91112AA
Long airbrick adaptor 91102AA
Universal support clip 91114AA
Duct connector 91107AA
Airbricks horizontal
terracotta 91103AA
white 91126AA
brown 91127AA
Cotswold stone 91128AA
Soldier course* 91246AA
100mm telescopic wall tube
91247AA
*terracotta
• An external grille shall be supplied with
the fan
The unit shall be rated at IPX5 making it
•
uitable for use in the splash zone 1 of a bath
s
r shower
o
• The fan housing shall be moulded in high
gloss ABS with the air inlet discreetly
concealed behind a baffle to the front cover
The front cover assembly shall be held in
•
osition by clips to facilitate ease of removal
p
or fan adjustment
f
• A balanced impeller shall be integral with the
motor assembly
• The fan shall be rated at 220-240 50/60Hz
verall dimensions W x H x D
O
52 x 300 x 156mm excluding spigot
2
• Profile 29 system components shall be used
in conjunction with Premier DX200 and
CF20 models
• The system shall use a XFD kit to connect to
the fan with further components appropriate
for the application
• The outer dimensions shall be w234 x h29mm
and have a cross sectional area of 5630mm
• Xpelair Profile 29 shall be manufactured in
self extinguishing flame retardant PVC
conforming to DIN 4102 B1 and UL94 V2
2
Xpelair DX100
The unit is to be supplied from the Xpelair DX100
range by Applied Energy Products Ltd,
Morley Way, Peterborough PE2 9JJ
Tel. +44 (0)1733 456789
ef
Model
DX100
DX100PC
DX100T 90841AW
DX100H 90842AW
DX100HP 90843AW
DX100PIR* 90844AW
*IPX4 rated
R
90839AW
90840AW
• The unit shall be designed for wall,
ceiling, shaft (or window mounting in
glass up to 6mm thick) using the kit
provided. An air operated backdraught
shutter shall be included
The fan housing shall be moulded in high
•
gloss white AB
design with finger guarding for additional
safety protection
The motor shall be lubricated for life with
•
built in safety thermal overload protection
• The unit shall be rated at IPX5
S and be of modern
• In addition it shall conform to Building
Regulations for use in toilets and bathrooms
• Dimensions shall be W x H x D
165 x 155 x 43mm excluding spigot
• PC - Pullcord
imer (2 - 20mins)
T - T
•
• H - Humidistat control (50 - 90%RH)
HP - Humidistat/T
•
assive infrared control
PIR - P
•
imer control
www.xpelair.co.uk
161
Xpelair Typical Specification
Page 3
Xpelair Typical Specification
Xpelair LoVolt LV100
he unit is to be supplied from the Xpelair
T
oVolt 100mm range by Applied Energy
L
roducts Ltd, Morley Way, Peterborough PE2
P
JJ Tel. +44 (0)1733 456789
9
Model Ref
LV100 90845AW
LV100PC 90846AW
LV100T 90847AW
LV100H 90848AW
LV100HP 90849AW
LV100PIR 90867AW
Xpelair Slimline 100
he unit is to be supplied from the Xpelair
T
L100 & SL150 range by Applied Energy
S
Products Ltd, Morley Wa
JJ Tel. +44 (0)1733 456789
9
Model Ref
SL100 91225AW
SL100P 91226AW
SL100T 91227AW
SL100HT 91228AW
y, Peterborough PE2
The unit shall be 12V Safety Extra Low
•
oltage design and supplied complete
V
with a remote SELV transformer
• The unit shall be designed for wall,
eiling, shaft (or window mounting in
c
lass up to 6mm thick) using the kit
g
rovided. An air operated backdraught
p
hutter shall be included
s
The fan housing shall be moulded in
•
high gloss white ABS and be of modern
design with finger guarding for additional
safety protection
The motor shall be lubricated for life with
•
uilt in safety thermal overload protection
b
The unit shall be designed for wall, ceiling,
•
shaft (or window mounting in glass up to
mm thick) using the kit provided
6
• Shall be designed so that the front grille
thickness is no more than 10mm
• The fan housing shall be moulded in
high gloss white ABS and be of modern
design with finger guarding for additional
safety protection
• The motor shall be lubricated for life with
built in safety thermal overload protection
• The unit shall be rated at IPX4 and a
double insulated appliance
The unit shall be rated at IPX5.
•
n addition it shall conform to Building
I
Regulations for use in toilets and bathrooms
• Dimensions shall be W x H x D
65 x 155 x 42mm excluding spigot
1
PC - Pullcord
•
T - Timer (2 - 20mins)
•
• H - Humidistat control (50 - 90%RH)
HP - Humidistat/Timer control
•
PIR - Passive infrared control
•
In addition it shall conform to Building
•
Regulations for use in toilets and bathrooms
• P models shall include integral pullcord
• T models shall include integral timer control
(3 - 15mins)
• HT models shall include integral humidity
control (45 - 99%RH) and timer control
• HP models shall include a variable speed
humidistat with integral pullcord giving full
speed override
• Dimensions shall be W x H x D
140 x 140 x 125mm (including 15mm flange)
Xpelair CentrX
The unit is to be supplied from the Xpelair
CentrX range by Applied Energy Products Ltd,
Morley Way, Peterborough PE2 9JJ
Tel. +44 (0)1733 456789
Model Ref
CT100 91236AW
CT100T
CT100HT
CT100+ 91239AW
CT100+P 91240AW
CT100+HT
162
91237AW
91238AW
91241AW
• The unit shall be of panel design with a
centrifugal high pressure performance
characteristic. The spigot outlet shall be
suitable for connection to 100mm
flexible or rigid wall tubes or ducting
Models shall be available with built in
•
time overrun and built in humidistat
auto control
The unit shall be rated at IPX4. The fan
•
shall conform to Building Regulations for use
in toilets, bathrooms and utility rooms
•
The housing shall be moulded in high
gloss white ABS. The front cover shall be
removable to facilitate removal and
adjustment
• The motor shall be fitted with sealed self
aligning maintenance free bearings and
include thermal overload protection
• P models shall include integral pullcord
• T models shall include integral timer control
(3 - 15mins)
• HT models shall include integral humidity
control (45 - 99%RH) and timer control
• Dimensions shall be: W x H x D
190 x 190 x 130mm
CT100
CT100+ 208 x 208 x 139mm including
17mm spigot
Page 4
pelair XIL Inline Shower Fan Systems
X
he unit is to be supplied from the Xpelair XIL
T
ange by Applied Energy Products Ltd,
r
orley Way, Peterborough PE2 9JJ
M
el. +44 (0)1733 456789
T
Model Ref
XIL System
XIL100 90329AW
XIL125 91242AW
XIL150 91244AW
IL T System with integral overrun timer
X
XIL100T 90330AW
XIL125T 91243AW
XIL150T 91245AW
XXS100 fan only 90331AW
XXS100T fan only 90332AW
Xpelair BriteX LoVolt & BriteX Turbo
The unit is to be supplied from the Xpelair
BriteX range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ
Tel. +44 (0)1733 456789
Model Ref
BX100C 92278AW
BX100W 92276AW
BX100CT 92279AW
BX100WT 92277AW
BX100+C 91249AW
BX100+W 91248AW
BX100+CT
BX100+WT 91250AW
91251AW
he system shall comprise:
T
• Inline axial fan
3m of 100mm dia. flexible duct
•
Four fixing clips
•
Inline backdraught shutter
•
• Internal ceiling grille in white
Outside soffit/wall grille in brown
•
T models shall include overrun timer function
•
djustable between 2 - 20mins (100 range)
a
and 3 - 15mins (125/150 ranges)
• The fan housing and grilles shall be moulded
in ABS. The internal and external grilles should
ave finger guard protection. The fan and air
h
perated backdraught shutter shall be
o
nstalled in the space above the ceiling at the
i
ighest point in the system
h
• The system shall be suitable for installation in
Zone 1 as defined by the IEE regulations
16th Edition
• The lamp shall be 12V 50W Safety Extra Low
Voltage sealed dichroic lamp with SELV
transformer. The fan shall be sited above the
ceiling at the highest point in the duct run. The
fan shall be manufactured in ABS and have a
maintenance free motor with safety thermal
overload protection. The fan shall be IPX4
when installed as per the instructions and
double insulated Class II. The kit shall contain
ducting, duct ties and a grille suitable for soffit
or gable end fitting
The motor shall be lubricated for life with built
•
n safety thermal overload protection
i
• The fan shall comply with Building
egulations for use in bathrooms and shower
R
ooms when typically installed
r
• The System shall be guaranteed for 3 years
(BriteX LoVo
• Supply voltage 220-240V 50Hz
• T models shall include integral timer function
adjustable between:Britex Lovolt 1-20 min
Britex Turbo 3-15 min
lt) or 2 years (BriteX Turbo)
Xpelair XIM
The unit is to be supplied from the Xpelair XIM
range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ.
el. +44 (0)1733 456789
T
Model
XIM100* 91252AW
XIM100T* 91253AW
XIM100+
XIM125
XIM150 91256AW
XIM150T
XIM200
*IPX2 rated
Ref
91254AW
91255AW
91257AW
91258AW
• The unit shall be suitable for ducted
applications where high humidity is present
The unit shall be of polymer construction with
•
spigots for attachment to the ductwork
• The impeller shall be of mixed flow design
with matching guide vanes. A QuickLock
installation cradle shall be provided for easy
installation
• The motor shall be maintenance free, with
greased for life bearings and safety
thermal overload protection
• T models shall include integral timer function
adjustable between 3 - 15mins
The units shall be IPX4 rated and conform to
•
Building Regulations for toilets, shower
rooms and bathrooms
• All models shall be 2 speed (except XIM100
and XIM100T)
An optional change over switch shall be
•
available, COS Ref. 90108AW
• The unit shall be a double insulated
appliance
• Overall dimensions W x H x D
100mm 189 x 177 x 238mm
125mm 200 x 217 x 263mm
150mm 192 x 244 x 293mm
200mm 230 x 279 x 354mm
www.xpelair.co.uk
163
Xpelair Typical Specification
Page 5
Xpelair Typical Specification
Xpelair Slimline 150
he unit is to be supplied from the Xpelair
T
L100 & SL150 range by Applied Energy
S
roducts Ltd, Morley Way, Peterborough PE2
P
JJ Tel. +44 (0)1733 456789
9
Model Ref
SL150 91229AW
SL150P 91230AW
SL150HT 91231AW
SL150HP 91496AW
SG150HP 92349AW
The unit shall be designed for wall, ceiling,
•
haft (or window mounting in glass up to
s
mm thick) using the kit provided
6
Xpelair GX6, GXC6 & GXC9
Shall be designed so that the front grille
•
hickness is no more than 10mm
t
The fan housing shall be moulded in
•
igh gloss white ABS and be of modern
h
esign with finger guarding for additional
d
afety protection
s
• The motor shall be lubricated for life with
built in safety thermal overload protection
• The unit shall be rated at IPX4 and a
double insulated appliance
In addition it shall conform to Building
•
egulations for use in toilets and bathrooms
R
P models shall include integral pullcord
•
T models shall include integral timer control
•
45sec - 15mins)
(
HT models shall include integral humidity
•
ontrol (45 - 99%RH) and timer control
c
• HP models shall include a variable speed
humidistat with integral pullcord giving full
speed override
Dimensions shall be W x H x D
•
90 x 190 x 130mm including
1
front flange depth 15mm)
(
he unit is to be supplied from the Xpelair
T
range by Applied Energy Products Ltd.
GX/GXC
Morley Way, Peterborough PE2 9JJ
el. +44 (0)1733 456789
T
Model Ref
GXC6 90850AW
GXC6T 90861AW
GX6 90800AW
GX6T 90812AW
GX6HT 90814AW
GX6HT2 90863AW
GXC6SC 91142AW
GXC9 89995AW
Xpelair GX6 EC2, GXC6 EC2
The unit is to be supplied from the Xpelair
C EC2 range by Applied Energy
GX/GX
Products Ltd. Morley Way, Peterborough PE2
9JJ Tel. +44 (0) 1733 456789
ef
Model
GX6 EC2
GXC6 EC2
• The 150mm extract fan shall be suitable for
window, wall or panel mounting
• Hole size in glass shall be 184mm.
An optional WK tube shall be used for wall
installation
R
92294AW
92295AW
The extract fan shall be suitable for window,
•
wall, or panel mounting. An optional WK tube
shall be used for wall installation
he motor shall be high efficiency, totally
• T
enclosed, with sealed for life bearings and
safety thermal overload protection
• The motor /impeller assembly shall be
housed in a rigid ABS moulded duct to
ensure even, optimum impeller tip clearance
• The inner grille shall be moulded in
white ABS with a high gloss finish and
incorporate a finger guard and removable
shutter cassette for ease of maintenance
• The impeller shall be pre-balanced and
removable for cleaning by means of a shaft
screw fixing
A trickle vent option shall be incorporated into
•
the mechanism to provide 4000mm
ventilation when the fan is Off
• The motor shall be an UltraEC type external
rotor motor with sealed for life bearings and
safety thermal overload protection.
Class II appliance
• The products shall be capable to be set at
one of two extract performances which will
satisfy Building Regulations Part F1 for
intermittant kitchen and Utility room use.
The rated wattage shall not exceed
0.036w/l/s for GX6 EC2 and 0.027w/l/s for
C6 EC2
GX
• The product shall be suitable for ambient
temperatures up to 50C
• The motor / impeller shall be housed in a rigid
ABS moulded duct to ensure even optimum
impeller clearance
2
passive
Operation of the shutter shall be by a silent
•
electrothermal actuator on GX6 variants and
6T; pullcord on GXC
GXC
he unit shall be BEAB approved
• T
• T models shall include integral timer function
adjustable between 2-20mins
• GX6HT shall include integral humidity
function (50-90%RH) and timer
• GX6HT2 shall include integral humidity and
timer function with 2 speeds
• GXC6SC shall be speed adjustable
• Overall dimensions for
GXC6 & GX6 210 x 226 x 112mm
GXC9 294 x 312 x 117mm
• The inner grille shall be moulded in whit ABS
with a high gloss finish and incorporate a
finger guard and removable shutter cassette
for ease of maintenance
• The impeller shall be pre balanced and
removable for cleaning by means of a shaft
screw fixing
• Operation of the shutter shall be by a silent
electrothermal actuator on GX6 EC2 and
pullcord on the GXC6 EC2
Overall dimensions for:
GX6/GXC6 EC2
WxHxD
210 x 226 x 112 mm
6 and GXC9
W x H x D
164
Page 6
Xpelair Premier DX400 & CF40
The unit is to be supplied from the Xpelair
Premier range by Applied Energy Products Ltd,
Morley Way, Peterborough PE2 9JJ
Tel. +44 (0)1733 456789
Model Ref
DX400 91083AW
DX400T 91084AW
DX400PC 91100AW
DX400RS 91085AW
CF40 91086AW
CF40TD 91087AW
CF40RSTD 91088AW
he unit shall be designed for flush or
• T
urface mounting in walls and ceilings
s
using the fixing clamps provided
An external grille shall be supplied with
•
he fan
t
Xpelair Kitchen Canopies
The unit is to be supplied from the Xpelair
Nouvelle Cuisine range by Applied Energy
Products Ltd, Morley Way, Peterborough
PE2 9JJ Tel. +44 (0)1733 456789
Model
Wall Chimney Canopies
Curved 900mm
Flat 900mm 600mm
Box 900mm 700mm
onda 900mm 600mm
T
Chimney 900mm 600mm
Island Chimney Canopy
Island
900mm
600mm
• DX400 fans shall have a two speed
unning facility and CF40 fans a room
r
ize selector in the control system to
s
rovide three preset speed settings for
p
optimum room performance
• A further option of trickle ventilation shall
e provided by way of a preset switch on
b
he unit (not DX400)
t
• CF versions shall be manually
adjustable between 50 and 90% RH with
an running status indicated by lights
f
The unit shall be BEAB approved and
•
rated IPX5. in addition the fan shall
conform to Building Regulations for use
n kitchens, utility rooms and bathrooms
i
The fan housing shall be moulded in high
•
gloss white ABS and be of modern design
with the air inlet discreetly concealed
behind a stylish baffle fixed to the front cover
The front cover assembly shall be
•
held in position by clips to facilitate ease
of removal for fan adjustment
Built in Canopies
Inset 520mm 282mm
Integrated 600mm
Standard 600mm
Standard Plus (SS) 600mm
• The kitchen canopy shall be offered in a
range of styles to suit wall, island and
integrated applications. Models shall be
available in stainless steel/glass or
white/brown finish to suit kitchen decor
and have seperate switchable integrated fan
and lighting
• The motor shall be of external rotor
onstruction, IP44 rated with sealed
c
aintenance free bearings and include
m
nbuilt safety thermal overload protection
i
• A dynamically balanced balanced impeller
shall be integral with the motor assembly
PC models shall be pullcord operated
•
• T models shall include integral timer function
adjustable between 30s-20mins
RS shall be remote switched use with MOS
•
ef. 90199AW
R
• TD shall have an integral timer
RSTD shall have an integral timer and remote
•
elay switch. MOS Ref. 90199AW
d
• Overall dimensions: W x H x D
249 x 297 x 147mm excluding 35mm spigot
• All models shall be suitable for extraction to
the outside using 125mm Xflex or Profile 60
flat duct systems or can be set for
recirculation, optional carbon filters to be
available
• The Wall, Island and Standard Plus models
shall be fitted with washable grease filters,
disposable acrylic filters on other integrated
models
• The three speed continuously rated motors
shall be maintenance free
• There shall be a choice of performance to
meet the minimum requirements of Building
Regulations
Three year guarantee
•
Xpelair Profile 60
The components are to be supplied from the
Xpelair Profile 60 range by Applied Energy
eterborough PE2
, P
Products Ltd. Morley W
9JJ. Tel. +44 (0)1733 456789
Model Ref
Straight duct 1m 89755AA
Straight duct 1.5m 91188AA
Horizontal bend adjustable
Horizontal 90 bend 89754AA
Vertical 90 bend 89753AA
Elbow/plenum to 100mm dia 89752AA
ay
89750AA
Elbow/plenum to 125mm dia 91259AA
Elbow/plenum to 150mm dia 91483AA
Duct coupling 89757AA
T piece 90091AA
t clip 89756AA
Suppor
all outlet grille
W
Flexible ducting 0.5m
eak intumescent
e br
Fir
89751AA
91484AA
91975AA
Round to rectangular adaptor 91482AA
• Profile 60 system components shall be used
in conjunction with Premier DX200 and CF20,
DX400 and CF40 models set at high speed
• Also suitable for Xpelair range of kitchen
canopies
The system shall use a plenum kit to connect
•
to the fan with further components
appropriate for the application
• The outer dimensions shall be 204 x 60mm
and have a cross sectional area of
11200mm
• Xpelair Profile 60 shall be manufactured in
self extinguishing flame retardant PVC
conforming to DIN 4102 B.M1
2
www.xpelair.co.uk
165
Xpelair Typical Specification
Page 7
Xpelair Typical Specification
Xpelair CX10 & CMF
T
he unit is to be supplied from the Xpelair CX
& CMF range by Applied Energy Products
Ltd. Morley Way, Peterborough PE2 9JJ
el. +44 (0)1733 456789
T
Model Ref
CX10 90209AB
CMF171 89955AW
CMF241 89956AW
• The unit shall be designed for flush ceiling
mounting in incorporate a finger guard for
afety protection
s
CX model shall be an axial fan unit and
•
MF models centrifugal
C
• The units shall be fully recessed with only the
high gloss ABS moulded grille showing
There shall be spigots for the attachment of
•
ptional ductwork
o
CMF271 89957AW
Xpelair Xplus Whole House Multipoint Extract Fans
The unit is to be supplied from the Xpelair Xplus
range by Applied Energy Products Ltd. Morley
Way, Peterborough PE2 9JJ
Tel. +44 (0)1733 456789
Model Ref
Xplus 275 91260AW
Xplus 340 91261AW
Xplus 340 DC 91262AW
Xplus 340 DCRF 91263AW
Controller 91457AW
• The extract fan unit shall be designed for the
ontinuous extraction of condensation and
c
dours from the ‘wet’ rooms of a dwelling. It
o
ay be installed in a loft space or services
m
upboard. Suitable ductwork such as
c
flex125 of Profile 60 shall be used with
X
egulAir ventilation terminals
R
The fan housing shall be manufactured in a
•
polymeric material and be fitted with three
125mm ‘room side’ extract spigots and one
125mm discharge spigot terminating at a wall
or roof
• CMF models shall have a cassette style
construction allowing first-fit ductwork to be
itted prior to the installment of the unit.
f
Motors shall be lubricated for life and be
•
aintenance free
m
• Safety thermal overload protection shall
be fitted
The fascia grilles shall be demountable to
•
acilitate cleaning
f
• The fan shall have a backward centrifugal
urved impeller. The motor shall be rated for
c
ontinuous running, have sealed for life
c
earings and be maintenance free. AC and
b
C motor variants shall be available
D
• All models shall be speed controllable using
an optional hard wired switch. Xplus
40 DCFRF shall also be available with a
3
100M (line of sight) wireless transmitter
control system
• Xplus 340 DC shall be AppendixQ listed and
meet Best Pactice Criteria
Xpelair Xplus 250 & 400 DC 8CV
The unit is to be supplied from the Xpelair
LoSound range by Applied Energy Products
Ltd. Morley Way, Peterborough PE2 9JJ.
Tel. +44 (0)1733 456789
Model Ref
Xplus 250DC8CV 92290AW
Xplus 400DC8CV
• There shall be two models with performances
ranging from 48m
to 402m
• Each model shall have 8 selectable set up
speeds to suit installation application with
speeds in accordance with Building
Regulations P
requirements selected via an integral switch
accessible from the outside of the product
3
3
/h to 255m3/h and 206m3/h
/h (at 0Pa)
art F1 continuous extract
92100AW
• To avoid tampering with speed settings in
use, the unit must be powered Off if switch
adjustment needs to be made. Altering the
switch position when the unit is powered will
not change the speed setting
• A Boost function shall be available to
increase extract rate by one set point i.e.
the boost speed of speed 1 is equivalent to
speed 2 etc. Speed 8 boost is 36m_/h above
speed 8
• Boost function shall be operated using
standard Xpelair controllers i.e. COS switch,
XRH, XPIRA, DT20, and AQS controllers
• The product shall be rated at 230V, 50/60Hz,
1 phase
• Main body shall be manufactured in impact
resistant polymeric material
• The unit shall be supplied with 1m of
4-core cable
• The unit shall have 3 intake connections of
125mm diameter and1 extract connection
125mm diameter
• Motor shall be Energy saving Longlife
UltraDC external rotor motor with greased for
life ball bearings
Systems using these products should design
•
to achieve a duct velocity of less than 3m/s in
order to minimise noise. The fan shall not
exceed a specific fan power of 0.6 w/l/s
@ 50pa
Xplus 250 DC 8CV shall be Appendix listed
•
and meet Best Practice Criteria
166
Page 8
pelair Xcell 150 & 200
X
Wholehouse ventilation unit from the Xpelair
Xcell range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ
el. +44 (0)1733 456789
T
Model Ref
Xcell 150 91981AA
Xcell 150R 91976AA
Xcell 150V 92004AA
Xcell 200 91977AA
Xcell 200BP 91979AA
Xcell 200R 91978AA
Xcell 200RBP
91980AA
Xpelair Xcell 270 LongLife
The unit is to be supplied from the Xpelair
Xcell range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ
el. +44 (0)1733 456789
T
Model Ref
Xcell 270 91264AW
Xcell 270BP 91265AW
• The MVHR unit shall have a slimline
insulated steel case with sealed access
panel. The unit shall be suitable for ceiling
or loft mounting in confined spaces
• The heat recovery cell shall be up to 92%
efficiency depending on volume setting
•
The unit shall be fitted with multispeed
double inlet fans for whisper quiet
performance to be set at a speed based
on the volume / duty of the dwelling in
accordance with Building Regulations Part
F
1. A remotely fitted switch shall be
provided with the unit
• Supply and exhaust filters shall protect
the cell (Xcell 200 only)
• The MVHR unit shall be designed for
installation in well insulated dwellings
• The unit shall be wall mounted using a
wall bracket provided with 150mm duct
spigots ready for connection to supply
and return air ducts and ductwork to a
wall or roof termination
• The cabinet shall be manufactured in steel
and powder coated in beige
• The inner components and scroll shall be
made from non hygroscopic high density
structural foam mouldings with an integral
double condensate tray. Provision shall be
made for alternative condensate drain
off points
• Hygenic coated steel anti-bacterial
condensate tray and outlet shall be fitted
•
Xcell 150 has two 125mm roomside
spigots
• Xcell 150R has a pair of twin flat duct
spigots for connection to Profile 60 duct
• Xcell 150V is a vertical version with all
spigots on top
• Xcell 200 has two 150mm roomside
s
pigots
• Xcell 200R has two pairs of twin flat duct
spigots for connection to Profile 60 duct
• Xcell 200BP and 200RBP shall have 100%
m
otorised summer bypass
• A hinged door shall be provided on the
front of the cabinet for access to the stage
1 G4 filters and occasional visual
inspection of the cell
• The unit shall have 3 speed from a choice
of twelve to match the volume of the
dwelling continuous ventilation including
the choice of a boost speed if required.
As a result the heat recovery cell
shall be up to 93% efficient
• The vent shall be be controlled by 3
speed selective switch Ref. 91266AW
Xpelair Xcell 300 & 400 LongLife
The unit is to be supplied from the Xpelair
Xcell range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ
el. +44 (0)1733 456789
T
Model Ref
Xcell 300
Xcell 400
Xcell 300BP
Xcell 400BP
91267AW
91269AW
91268AW
91270AW
• The MVHR unit shall be designed for
installation in well insulated dwellings
• The unit shall be wall mounted using a wall
bracket and provided with 150mm duct
spigots on the 300 models and 180mm duct
spigots on the 400 models ready for
connection to supply and return air ducts and
ductwork to a wall or roof terminations
• The cabinet shall be manufactured in
polypropylene to RAL 9002: White
• The inner components and scroll shall be
made from non hygroscopic high density
structural foam mouldings with an integral
double condensate tray. Provision shall be
made for alternative condensate drain
off points
• Backward curved impeller
• Access shall be provided to the stage 1
G3 filters. The unit shall have a choice of
speeds to match the volume of the dwelling
in order to provide half an air change per
hour continuous ventilation including the
choice of a boost speed if required. As a
result the heat recovery cell shall be up to
91% efficient - certified by TZWL
on chosen speed. The fans shall be
electronically balanced to provide equal
extraction and air supply
• The motors shall be UltraDC motors
with maintenance free greased for life
ball bearings
• A supply lead shall be provided to
facilitate wiring
Overall Dimensions W x H x D
•
740 x 600 x 540mm
Weight :32kg
, depending
www.xpelair.co.uk
167
Xpelair Typical Specification
Page 9
Xpelair Typical Specification
Xpelair Xcell 600 Low Profile
The MVHR unit shall have a slimline insulated
The unit is to be supplied from the Xpelair
Xcell range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ
el. +44 (0)1733 456789
T
Model Ref
Xcell 600 92002AA
Xcell 600BP 92003AA
Xpelair Profile 150
•
teel case and sealed access panel. The unit
s
hall be suitable for ceiling or loft mounting in
s
onfined spaces using the integral mounting
c
oint detail provided
p
• The heat recovery unit shall be up to 70%
efficient depending on volume setting and be
compatible with heat pump systems
The unit shall be fitted with double inlet fans
•
or quiet operation and be set at a speed
f
alculated on the volume/duty of the dwelling
c
n accordance with Building Regulations Part
i
F1. A remotely fitted single gang switch shall
be provided with the unit. Heavy duty supply
and exhaust filters shall be included in
the unit
The condensate tray shall have an anti
•
acterial coating. The unit shall have 200mm
b
pigots on the room side and discharge side
s
A further model shall be available fitted with a
•
motorised summer Bypass feature
• Dimensions H x W x L
50 x 750 x 1100mm (Excluding spigots)
2
The components are to be supplied from the
Xpelair Profile 150 range by Applied Energy
Products Ltd. Morley Way, Peterborough
PE2 9JJ.
Tel. +44 (0)1733 456789
Model Ref
2.5m straight duct 91272AA
90º bend 91273AA
45º bend 91274AA
30º bend 91275AA
15º bend 91276AA
Pushfit collar 91279AA
Snap Clamp Collar
91280AA
Xpelair EverDri LongLife
The unit is to be supplied from the Xpelair EverDri
range by Applied Energy Products Ltd. Morley
Way, Peterborough PE2 9JJ.
Tel. +44 (0)1733 456789
Model Ref
XEDL
• For installation in houses
• The fan unit shall be designed for fully
automatic operation and continuous running
and supplied complete with anti vibration
mountings, interconnecting flexible ducting
and purpose designed diffuser outlet with
direction baffles
90998AA
Roof Cowl 91277AA
Wall Cowl 91278AA
• Profile 150 ductwork shall be used in
conjunction with Xflex ductwork and Profile
60 flat duct to provide the distribution
system for Xcell MVHR units
• Ducting shall be manufactured in steam
resistant, self extinguishing EPE to class
B1, DIN 4102
• Density shall be 50kg/m
3
and the duct
shall have a thermal coefficient of 0.040
W/m. K measured at 0ºC in accordance
with DIN 52613. Temperature range shall
be -40 to +100ºC
• The unit shall continuously monitor the loft air
temperature and will automatically adjust the
performance of the fan if the temperature
rises above or falls below 19
• The fan shall automatically suspend
operation if the temperature rises above 25
and re-continue when the temperature falls
back down below that point.
• Four performance selection settings shall be
provided on the unit to provide the optimum
performance settings for differing dwelling
sizes and severity of condensation.
• The operation status of the unit shall be
indicated by means of LED’s on the
control panel.
C.
°
• A selection of bends constructed of the
same material shall be available. The duct
and bends shall be connected using
100mm collar connectors with built in
internal stops. For duct sections requiring
subsequent disconnection for service or
cleaning access, a quick release collar
shall be available
• Further interconnecting components shall
be available from the Profile 60 flat duct
range to complete the system
• The fan motor shall be a high efficiency
electronically commutated DC motor with
sealed for life maintenance free bearings and
thermal protection. Quiet running of the fan
shall be ensured by incorporation of a
forward curved centrifugal impeller operating
°C
in a double inlet scroll housing.
• The fan shall be supplied complete with a
supply cord fitted.
The incoming air shall pass through a filter
•
these are to be available as a spare part
from Xpelair
.
,
168
Page 10
pelair LoVolt XHR150
X
he unit is to be supplied from the Xpelair XHR
T
ange by Applied Energy Products Ltd. Morley
r
ay, Peterborough PE2 9JJ
W
el. +44 (0)1733 456789
T
Model Ref
XHR150PC 90821AA
XHR150HP 90820AA
The single room heat recovery ventilator shall
•
e a Safety Extra Low Voltage LoVolt product
b
nd supplied complete with exterior weather
a
esistant bezel and a remote SELV transformer
r
Xpelair AutoFlow
The unit is to be supplied from the Xpelair
utoFlow range by Applied Energy Products
A
td. Morley Way,
L
Tel. +44 (0)1733 456789
Model Ref
AutoFlow80 91295AW
AutoFlow100 91296AW
AutoFlow160 91297AW
Peterborough PE2 9JJ
The unit shall have two speeds: trickle for
•
onstant background ventilation and a boost
c
speed operated manually by way of a built in
pullcord on the PC model and by way of an
automatic humidity sensor control on the
HP model
The unit shall be of cylindrical construction
•
ith integral outside intake / extract points
w
• The internal grille shall be moulded in
white ABS with a high gloss finish and
incorporate a safety finger guard. To avoid
cross contamination, the incoming air shall
e delivered to the room at the side of the
b
rille ensuring a 90º separation from the
g
The ventilator shall be installed using a
•
ore cutting drill
c
The Passive ventilator shall be self regulating
•
using a temperature sensitive piston to
adjust the airflow in relation to the outside air
temperature. The piston shall be maintenance
free. In automatic mode the airflow shall
decrease with declining outdoor temperature
and increase with rising outdoor temperature.
The vent disc shall be insulated and tight
fitting to the bezel when closed
utgoing air. The incoming air shall be filtered
o
hrough a foam filter medium
t
• The ventilator shall be fitted with a long life
luminium heat recovery cell having an
a
fficiency of up to 80%
e
BBA Agreement Board Certification
•
• Overall dimensions:
W x H x L
200 x 180 x 532mm
The vent disc shall be capable of being
•
djusted manually by rotating the disc from
a
utomatic mode to increase or decrease the
a
pening size. The temperature range shall be
o
from -5ºC to +10ºC
• The disc, wall tube and external grille shall be
manufactured in ABS. The inside disc, bezel
and the external weather grille shall be white
in colour
Xpelair GX6, GX9 & GX12
The unit is to be supplied from the Xpelair GX
range by Applied Energy Products Ltd. Morley
Way, Peterborough PE2 9JJ
el. +44 (0)1733 456789
T
Model Ref
GX6 90800AW
GX9 89994AW
GX12
• The fan shall be suitable for window
mounting (or wall mounting using optional
wall kit)
erformance shall have been proven by
P
•
type testing in accordance with B
1 and FID performance determined to be:
3
/h)
(m
GX6 266
GX9
GX12
extract
728
1614
90012AW
S 848 Part
intake
456
1002
• All models shall have totally enclosed AC
motors with sealed for life bearings with
external rotor motors on GX9 / GX12 and
safety thermal overload protection
• The high efficiency moulded axial bladed
impeller shall be pre-balanced and
designed for optimum performance and
ease of removal for cleaning
Motor/impeller assembly shall be in a rigid
•
ABS housing with high gloss white finish
and incorporate a finger guard
• A passive trickle vent option shall be
incorporated into the inner grille shutter
cassette to provide low level ventilation
when the unit is not in use
• The shutter shall be operated by a silent
electrothermal actuator
It shall be possible to remove the inner grille
•
and shutter cassette separately for cleaning
• An outer grille shall be provided, this to be
moulded in Shadow Grey ABS with high
gloss finish and incorporate weather
resistant vanes
• On GX9 and GX12 models customer
electrical connection shall be via an internal
tamper-proof plug and socket
On GX9 and GX12 models a concealed
•
switch on the unit shall predetermine the
mode of operation: intake only, or extract
only or optional controller operation for
speed control and reversibility
• The unit shall be BEAB approved
Overall dimensions: W x H x D
GX6 210 x 226 x 112mm
GX9 294 x 312 x 117mm
GX12 380 x 408 x 161mm
External depth shall be 32mm/32mm
and 34mm respectively
www.xpelair.co.uk
169
Xpelair Typical Specification
Page 11
Xpelair Typical Specification
Xpelair PX6, PX9 & PX12
he unit is to be supplied from the Xpelair PX
T
ange by Applied Energy Products Ltd.
r
orley Way, Peterborough PE2 9JJ
M
el. +44 (0)1733 456789
T
Model Ref
PX6 91300AW
PX9 91299AW
PX12 91298AW
• The fan shall be suitable for ceiling or panel
mounting. Performance shall have been
proven by type testing in accordance with
BS 848 Part 1 and FID performance
determined to be:
3
m
h) extract intake
(
/
X6 246
P
X9 790 458
P
X12 1712 1070
P
Xpelair RX6, RX9 & RX12
The unit is to be supplied from the Xpelair RX
range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ
Tel. +44 (0)1733 456789
Model Ref
RX6 90818AW
RX9 90424AW
RX12 90425AW
All models shall have totally enclosed AC
•
otors with sealed for life bearings, with
m
external rotor motors on PX9 / PX12, and
safety thermal overload protection
• The high efficiency moulded axial bladed
impeller shall be pre-balanced and
designed for optimum performance and
ase of removal for cleaning
e
Motor/impeller assembly shall be in a rigid
•
BS housing with high gloss white finish
A
nd incorporate a finger guard
a
• A passive trickle vent option shall be
incorporated into the inner grille shutter
cassette to provide low level ventilation
hen the unit is not in use
w
The shutter shall be operated by a silent
•
lectrothermal actuator
e
• It shall be possible to remove the inner grille
and shutter cassette separately for cleaning
on PX9 and PX12 models
• The fan shall be suitable for roof mounting
through clear and obscure glazing,
polycarbonate sheeting, roof mounting
plates and materials up to 25mm
• On non smooth glass surfaces a suitable
sealant shall be applied to the outer gasket
• Performance shall have been proven by
type testing in accordance with BS 848 Part
1 and FID performance determined to be:
3
/h) extract intake
(m
RX6(T) 206
RX9 511 438
RX12 1100
• All models shall have totally enclosed AC
motors with sealed for life bearings, with
external rotor motors on RX9 / RX12, and
safety thermal overload protection
The high efficiency moulded axial bladed
•
impeller shall be pre-balanced for optimum
performance and ease of removal for
cleaning
• Motor/impeller assembly shall be in a rigid
S housing with high gloss finish and
AB
incorporate a finger guard
915
Customer electrical connection shall be via
•
n internal tamper- proof plug and socket
a
on PX9 and PX12 models
• A concealed switch on the unit shall
redetermine the mode of operation: intake
p
nly, or extract only or optional controller
o
peration for speed control and reversibility
o
PX9 and PX12 only)
(
• The unit shall be BEAB approved
• Overall internal projection shall be:
X6 11mm
P
X9 / PX12 18mm
P
• A passive trickle vent option shall be
incorporated into the inner grille shutter
cassette to provide low level ventilation
when the unit is not in use
• The shutter shall be operated by a silent
electrothermal actuator
• It shall be possible to remove the inner grille
and shutter cassette separately for cleaning
• An outer roof cowl with internal deflector
shall be provided, this to be moulded in
ABS with high gloss UV stabilised finish on
RX9 and RX12 models
• Customer electrical connection shall be via
an internal tamper-proof plug and socket on
RX9 and RX12 models
• A concealed switch on the unit shall
predetermine the mode of operation:
intake only
controller operation
• The unit shall be BEAB approved
• Overall internal projection shall be:
RX6
RX9 117mm
RX12 161mm
, or extract only or optional
112mm
170
Page 12
Xpelair WX6, WX9 & WX12
The unit is to be supplied from the Xpelair WX
range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ
Tel. +44 (0)1733 456789
Model Ref
WX6 90822AW
WX6T 90823AW
WX9 89996AW
WX12 90011AW
• The fan shall be suitable for wall mounting
Installation shall be mortar free and the
•
roduct shall be supplied complete with
p
all liner
w
Performance shall have been proven by
•
type testing in accordance with BS 848 Part
1 and FID performance determined to be:
3
m
h) extract intake
(
/
X6(T) 246
W
X9 783 477
W
X12 1715 969
W
• All models shall have totally enclosed AC
motors with sealed for life bearings, with
external rotor motors on WX9 / WX12, and
safety thermal overload protection
he high efficiency moulded axial bladed
T
•
mpeller shall be pre-balanced and
i
esigned for optimum performance and
d
ase of removal for cleaning
e
• Motor/impeller assembly shall be in a rigid
ABS housing with high gloss white finish
and incorporate a finger guard
• A passive trickle vent option shall be
incorporated into the inner grille shutter
cassette to provide low level ventilation
when the unit is not in use
• The shutter shall be operated by a silent
electrothermal actuator
It shall be possible to remove the inner grille
•
nd shutter cassette separately for cleaning
a
An outer grille shall be provided, this to
•
be moulded in Shadow Grey ABS with
high gloss finish and incorporate
weatherproof vanes
On WX9 and WX12 models customer
•
lectrical connection shall be via an internal
e
amper-proof plug and socket
t
• On WX9 and WX12 models a concealed
switch on the unit shall predetermine the
mode of operation: intake only, or extract
only or optional controller operation for
speed control and reversibility
The unit shall be BEAB approved
•
• Overall internal projection shall be:
WX6 11mm
WX9 / WX12 18mm
Xpelair WXXL
The unit is to be supplied from the Xpelair
WXXL range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ
Tel. +44 (0)1733 456789
Model Ref
Extract models
WXXL350 91301AA
WXXL400
WXXL450
Intake models
WXXLS350 91383AA
WXXLS400 91384AA
WXXLS450 91385AA
91302AA
91303AA
• WXXL models shall have G.S.M.telescopic
wall liner suitable for installation in solid and
cavity walls from 275mm to 375mm
• The external rotor motor rated at IP44 shall
be fitted with sealed for life maintenance
free bearings
• On the inner wall face the fan shall be fitted
with a white epoxy coated aluminium
internal wall grille with removable core for
easy cleaning. The fan assembly shall be
separately guarded for additional safety
• The shutter shall be manufactured from
aluminium housed behind a anodised
aluminium external weather louvre
• On intake models the shutter shall be
electro-mechanically opened and be fitted
with a washable prefilter
• The fan shall have a built in three speed
control. A separate slimline three position
and off selection switch shall be provided
for remote wall mounting
www.xpelair.co.uk
171
Xpelair Typical Specification
Page 13
Xpelair Typical Specification
Xpelair ChefX
The unit is to be supplied from the Xpelair
ChefX range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ
Tel. +44 (0)1733 456789
Model Ref
ChefX Tempo 91309AA
ChefX Presto 91310AA
ChefX Mezzo 91311AA
Controls for Presto/Mezzo
Transformer 91369AA
Xpelair Digitemp
The unit is to be supplied from the Xpelair
Digitemp range by Applied Energy Products
Ltd. Morley Way, Peterborough PE2 9JJ
l. +44 (0)1733 456789
Te
Model Ref
Cooling
WA210N 91173AA
WA245N 91174AA
Heating & cooling
WHP210N 91175AA
WHP245N 91154AA
• Professional quality extract canopy of robust
onstruction designed for spot ventilation in
c
ood preparation and wash up areas.
f
esigned for exhaust operation to the
D
utside using rigid ductwork supplied
o
by others
• The canopy housing shall be manufactured
n stainless steel with G.S.M internal support
i
Washable grease filters shall be provided
•
• The hood shall have an integral fan
assembly with continuously rated motor and
ealed for life beatings. The motor shall be
s
PX4 rated and be suitable for temperatures
I
o
p to 65
u
C
• The three speed unit shall be designed for
surface mounting on walls at high or low
evel without the need for an external
l
ondenser
c
• Two airside wall tubes shall be provided for
fitting through 155mm sloping core drilled
holes through the external wall to the outside
• The maximum length of the tubes shall
be 1000mm
• Two folding external grilles shall be supplied
for fitting through the wall tubes from within
the room
• All “cooling only” (WA210N & WA245N) units
shall not require a condensate drain
• Control shall be from a full function hand
held infrared controller with a range of 8m
• The unit refrigerant shall be factory sealed
with no opening of the system or hose
connections on site
• Refrigerant R410a shall be used having an
Ozone Depletion Power Rating of ‘0’
• The motor shall be speed controllable using
ptional electronic controller or a five step
o
oltage transformer. The tempo model shall
v
e fitted with a built in speed controller and
b
ntegral lighting
i
• Dimensions
x W x L
empo 180 x 600 x 540
T
resto 2350 x 1000 x 460
P
Mezzo 400 x 1000 x 1000
• Performance @ 100pa duct resistance
empo 400m
T
resto 2200m
P
ezzo 2800m
M
• The unit shall be fitted with a pollen filter
The unit shall be sound insulated and have
•
super quiet night time function
a
• The unit shall have a self-diagnostic system,
which displays the condition of the unit
using a series of LEDs
• Performance shall be as follows:
model cooling heating
WA210N 2.1
WA245N 2.45
WHP210N 2.1 1.9
WHP245N 2.45 2.03
• Overall dimensions:
WxHxD 870 x 400 x 280mm
Min. diameter of holes: 155mm
H
3
h
/
3
h
/
3
h
/
kW kW
Xpelair WH30, WH60 & WHP30
The unit is to be supplied from the Xpelair WH
range by Applied Energy Products Ltd. Morley
Way, Peterborough PE2 9JJ
Tel. +44 (0)1733 456789
Model Ref
WH30 98392AC
WH60
WHP30 89999AW
172
00147AC
• The space heater shall be suitable for wall
mounting and in the case of the 6kW
version also suitable for suspension
from above
• The unit shall be capable of being adjusted
both in the vertical and horizontal planes
and then fixed in position
The industrial models shall have a robust
•
steel casing with die cast aluminium guards.
• Commercial model shall have a flame
retardant polycarbonate/glass filled nylon
case finished in white and grey
• The heating elements shall be of spiral
wound nichrome wire design
• The fan shall have a totally enclosed,
continuously rated, maintenance free motor
with greased for life bearings
• The terminal block shall be easily accessible
for wiring in position
• A control unit shall be available for the 3kW
versions to enable the fan to be run during
warmer months or fan heater mode with
thermostatic control for heating
The 3kW versions shall be suitable for
•
connection to a single phase supply
6kW model shall be suitable for connection
to either a singe phase or three phase supply
• Overall dimensions including mounting
bracket with the unit mounted vertically:
W x H x D
WH30 254 x 368 x 270mm
WH60 276 x 429 x 327mm
WHP30 267 x 370 x 370mm
. The
Page 14
Xpelair DCH3000A
he unit is to be supplied from the Xpelair DCH
T
ange by Applied Energy Products Ltd. Morley
r
ay, Peterborough PE2 9JJ.
W
Tel. +44 (0)1733 456789
Model Ref.
DCH3000A 90792AW
Xpelair PlinthHeat
he unit is to be supplied from the Xpelair
T
linthHeat range by Applied Energy Products
P
Ltd. Morley Way, Peterborough PE2 9JJ.
el. +44 (0)1733 456789
T
Model Ref
With integral control switches:
PlinthHeat W 91465AW
PlinthHeat B 91466AB
PlinthHeat S 91312AW
With remote controls*:
PlinthHeat WR 91467AW
PlinthHeat BR 91468AB
PlinthHeat SR 91313AW
*remote controller 87100
The fan assisted heater shall be suitable for
•
all mounting by way of two mounting
w
oints to the rear of the cabinet
p
The heater shall not require any feet and
•
shall be mounted clear of the floor surface
• The tangential fan shall be balanced. The
otor shall be maintenance free with sealed
m
or life bearings and safety thermal overload
f
rotection. In addition there shall be a
p
afety cut out with disconnection from the
s
ains to reset
m
• The heating element shall be a spiral
wound design. There shall be three
switches providing On/Off, and 1kW, 2kW or
kW output. A further rotary knob will permit
3
he setting of the room temperature for
t
The fan assisted heater shall be suitable for
•
installation in the standard plinths of a
itchen cabinet of 120mm or more
k
here shall be an air inlet on either side of
• T
the fascia plate and three horizontal outlet
grille sections in the centre
• The fascia shall be available in two powder
coated finishes and additionally available
in brushed stainless steel to match the
kitchen decor
• The fascia shall have six fixing holes for
secure attachment to the plinth
• The heating element shall be a spiral
wound design
• There shall be two switches on the integral
control model providing On/Off, and 1kW
or 2kW output. A lamp shall indicate the
output chosen
utomatic operation and lamp shall indicate
a
he unit is operating
t
The unit shall be BEAB approved
•
• Overall dimensions W x H x D
A separate kit shall be available for the
•
remote operated versions consisting of a
hermostat and means of isolation. For
t
safety the heater shall have an automatic
thermal cutout
• The fan shall be of axial design with a
maintenance free motor having sealed for
life bearings and safety thermal overload
protection
• Overall dimensions: W x H x D
• Hole dimensions shall be 95 x 440mm
* Requires remote thermostatic control kit
consisting of wall mounted single stage
variable thermostat, fused double pole
switch, two gang box and cable wall clamp.
Ref. 87100
505 x 265 x 110mm
470 x 120 x 240mm
Xpelair ScreenHeat
The unit is to be supplied from the Xpelair
ScreenHeat range by Applied Energy Products
Ltd. Morley Way, Peterborough PE2 9JJ.
Tel. +44 (0)1733 456789
Model
1.5 - 3kW
2.25 - 4.5kW
Ref
91469AW
91470AW
• The hot air curtain shall be suitable for wall
or ceiling mounting using the brackets
provided. The units shall be in standard
600mm modular widths for side by side
mounting over larger width doorways
• The brackets shall have key hole slots for
easy installation
• Motor shall be shaded pole, maintenance
free, with sealed for life bearings and safety
thermal overload protection
• The fan shall be tangential and balanced to
provide quiet vibration free operation
• The element shall be of open coil
construction and supported by ceramic
insulators
• The casing shall be manufactured in zinc
coated steel, externally powder coated in a
white finish
Overall dimensions:
•
www.xpelair.co.uk
W x H x D
610 x 185 x 105mm
173
Xpelair Typical Specification
Page 15
Xpelair Typical Specification
Xpelair Whispair
he unit is to be supplied from the Xpelair
T
hispair range by Applied Energy Products
W
Ltd. Morley Way, Peterborough PE2 9JJ.
Tel. +44 (0)1733 456789
Model Ref
NWAN36 900mm 90409AW
NWAN48 1200mm 90410AW
NWAN56 1400mm 90411AW
NWAN60 1500mm 90412AW
The unit shall be suitable for suspension
•
from a ceiling using the ceiling anchor and
suspension rod with integral anti-vibration
bobbin provided
Two lengths of rods shall be provided
•
namely 375mm and 750mm
• The fan blades shall be powder coated
teel and suitable for high humidity
s
nvironments
e
Air delivery shall be:
•
3
lade dia. m
B
00mm 8761
9
1200mm 10890
400mm 12474
1
500mm 13959
1
The motor shall be a continuously rated,
•
capacitor start and run, external rotor motor
design. It shall be maintenance free and
ncorporate two sets of caged ball bearings
i
or long life. The motor shall be suitable for
f
ot and humid conditions up to 40ºC
h
• Colour: White
Supply Voltage: 220-240V 50/60Hz
•
Xpelair Single Whispair Controller WAC1
Ref. 21852AW
Two slide switches provides On/Off
•
peration and 5 speed settings. Complete
o
ith transformer controller for quiet
w
operation and ‘fan running’ indicator light
Xpelair Group Whispair Controller WAC6
ef. 21853AW
R
For the simultaneous speed control of 1 to
•
6 Whispair units. Two slide switches
provides On/Off operation and infinitely
vailable speed settings
a
• Complete with ‘fan running’ indicator light
h
/
pelair Group Whispair Reversing
X
ontroller WAC6R
C
Ref. 21878AW
• For the simultaneous speed control of 1 to
Whispair units. Two slide switches
6
rovides On/Off operation and infinitely
p
ariable speed settings. Complete with
v
fan running’ indicator light and choice of
‘
winter/summer upwards or
downwards airflow
pelair Whispair Auto Temperature
X
ontroller AWC
C
Ref. 21857AW
• De-stratification controller supplied with two
thermo sensors at high / low level
onitoring between preset minimum and
m
aximum values. For the simultaneous
m
speed control of 1 to 10 Whispair units.
Three slide switches provides On/Off
operation and upwards or downwards
otation, manual override
r
Complete with fan running light
•
• w210 x h86 x d45mm
Xpelair Electrostatic Air Cleaners
The unit is to be supplied from the Xpelair EAC
range by Applied Energy Products Ltd. Morley
Way, Peterborough PE2 9JJ.
Tel. +44 (0)1733 456789
Model Ref
Surface mounted
Airflow: 400 to 1000m3/h
EAC400W White 89861AW
EAC400K Black/woodgrain 89869AK
Airflow: 1000 to 2000 m3/h
EAC700W White 89862AW
EAC700K Black/woodgrain
ecess mounted
R
Airflow: 420 to 780m3/h
EACF400W Off White 90015AW
Airflow: 1080 to 1500m3/h
89870AK
• The electrostatic filtration unit shall be
suitable for surface, and recess mounting,
on ceilings
• The unit shall be supplied with a remote
control to provide On/Off operation and
variation in fan speed
The electrostatic cell shall be manufactured
•
in aluminium having filtration effective to
0.01 microns. There shall additionally be a
pre-filter to capture general airborne
particles
• The unit shall have a status indicator panel
and a 'wash' indicator panel LED shall
illuminate when the electrostatic cell and
pre-filter require cleaning
• The casing of the surface models shall be
manufactured in a polymeric material
The flush model shall be of G.S.M.
•
construction with a pressed steel fascia
louvre coated studio finish off white, ready
for painting to tone with ceiling décor
• The grille pattern shall provide a wide
coverage
• Overall dimensions:
EAC 400 485 x 273 x 739
EAC 700 739 x 320 x 739
EACF 400 570 x 343 x 572
Class 1 Earthed appliance
•
• Supply voltage: 220-240V 50Hz
W x H x D
174
Page 16
Xpelair Scimitar XPMS
The unit is to be supplied from the Xpelair
XPMS range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ.
Tel. +44 (0)1733 456789
Model Ref
XPMS315-12 91526AA
XPMS315-14 91527AA
XPMS355-14 91529AA
XPMS400-14 91530AA
XPMS400-16 91531AA
XPMS450-14 91532AA
XPMS450-16 91533AA
XPMS500-14 91534AA
XPMS500-16 91535AA
XPMS560-14 91536AA
XPMS560-16 91537AA
XPMS630-16 91539AA
Xpelair Scimitar XSCS
The unit is to be supplied from the Xpelair
range by Applied Energy Products Ltd.
XSCS
orley Way, Peterborough PE2 9JJ.
M
Tel. +44 (0)1733 456789
Model Ref
XSCS315-12 91570AA
XSCS315-14 91571AA
XSCS355-14 91573AA
XSCS400-14 91574AA
XSCS400-16 91575AA
XSCS450-14 91576AA
XSCS450-16 91577AA
XSCS500-14 91578AA
XSCS500-16 91579AA
XSCS560-14 91580AA
XSCS560-16 91581AA
XSCS630-16 91583AA
• The fan shall be suitable for reverse operation
The fan plate shall be manufactured from a
•
ingle steel pressing to ensure perfect form
s
f the inlet bell mouth and uniformity of
o
mpeller tip clearance
i
• The fan body, impeller and motor housing
shall be further protected from deterioration
by coating with corrosion resistant powder
oat finish
c
The motor shall be IP44 and IP54 rated
•
xternal rotor type, AC capacitor start and
e
un and have sealed for life ball bearings.
r
Terminals will be provided for connection to
an external thermal/overload protection device
• Insulation is to be rated to class F
Impellers shall be high efficiency, low noise
•
ressed steel sickle blade design. Rotors and
p
mpellers are to be dynamically balanced to
I
ISO 1940-1:1986 Grade G 6.3
• The fan housing shall be manufactured from
galvanised steel. Drilled flanges shall be
provided at either end of the case
• The fan body, impeller and motor housing
shall be further protected from deterioration
by two coats of corrosion resistant powder
coat finish
• Motor mounting shall be via rigid welded
steel rod construction and support the
motor at four points
• The unit shall be capable of mounting at
any angle or in any plane
• The motor shall be IPX4 rated external rotor
type, AC capacitor start and run and have
sealed for life ball bearings and inbuilt
thermal protection. Insulation is to class F
Impellers shall be high efficiency
•
pressed steel sickle blade design
, low noise
• Customer connection shall be conveniently
located in an IP54 rated terminal box
ocated on the rear of the motor
l
The fans shall be suitable for use in ambient
•
emperatures ranging from -30°C to +60°C
t
nd higher on selected models
a
• All fans shall be supplied with an integral
inlet guard to EN294
The fan shall be fully speed controllable
•
sing the appropriate speed controller or 5
u
tep auto transformer (available as an
s
ncillary)
a
Must be suitable for 220-240V IPH 50Hz
•
electrical supply
• Rotors and impellers are to be dynamically
balanced to ISO 1940-1:1986 Grade G 6.3
ustomer connection shall be conveniently
• C
located in an IPX4 rated terminal box
attached to the body of the fan
• Terminals shall be provided within the
terminal box for connection to an external
thermal overload protection device
• The fans shall be suitable for use in ambient
temperatures ranging from –30°C to +60°C
minimum and higher on selected models
• The fan shall be fully speed controllable
using the appropriate speed controller or 5
step auto transformer (available as an
ancillary)
Must be suitable for 220-240V IPH 50Hz
•
electrical supply
Xpelair Rapier XPMA
The unit is to be supplied from the Xpelair
XPMA range by Applied Energy Products Ltd.
eterborough PE2 9JJ.
, P
ay
Morley W
Tel. +44 (0)1733 456789
Model Ref
XPMA315-12
XPMA315-14
XPMA355-14
XPMA400-14 91545AA
XPMA400-16 91546AA
XPMA450-14 91547AA
XPMA450-16 91548AA
XPMA500-14 91040AA
XPMA500-16 91549AA
XPMA560-16
XPMA630-16 91050AA
XPMA710-16 91055AA
91540AA
91541AA
91543AA
91550AA
• The fan shall be suitable for reverse operation
The fan plate shall be manufactured from a
•
single steel pressing to ensure perfect form
of the inlet bell mouth and uniformity of
impeller tip clearance
• The fan body, impeller and motor housing
shall be further protected from deterioration
by coating with corrosion resistant powder
coat finish
The motor shall be IP44 and IP54 rated
•
external rotor type, AC capacitor start and
run and have sealed for life ball bearings.
erminals will be provided for connection to
T
an external thermal/overload protection device
• Insulation is to be rated to class F
• Impellers shall be high efficiency, low noise
pressed steel sickle blade design
• Rotors and impellers are to be dynamically
balanced to ISO 1940-1:1986 Grade G 6.3
•
Customer connection shall be conveniently
located in an IP54 rated terminal box
located on the rear of the motor
• The fans shall be suitable for use in ambient
temperatures ranging from -30
and higher on selected models
• All fans shall be supplied with an integral
inlet guard to EN294
The fan shall be fully speed controllable
•
using the appropriate speed controller or 5
step auto transformer (available as an
ancillary)
Must be suitable for 220-240V IPH 50Hz
•
electrical supply
°
www.xpelair.co.uk
C to +60
°C
175
Xpelair Typical Specification
Page 17
Xpelair Typical Specification
Xpelair Rapier XSCA
The unit is to be supplied from the Xpelair
XSCA range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ.
Tel. +44 (0)1733 456789
Model Ref
XSCA315-12 91584AA
XSCA315-14 91585AA
XSCA355-14 91587AA
XSCA400-14 91589AA
XSCA400-16 91590AA
XSCA450-14 91591AA
XSCA450-16 91592AA
XSCA500-14 91078AA
XSCA500-16 91593AA
XSCA560-16
91594AA
XSCA630-16 91595AA
XSCA710-16 91597AA
Xpelair Rapier Roof XRA
The unit is to be supplied from the Xpelair XRA
ange by Applied Energy Products Ltd. Morley
r
Way, Peterborough PE2 9JJ.
Tel. +44 (0)1733 456789
Model Ref
XRA315-12 91997AA
XRA350-14 91998AA
XRA400-14 91999AA
XRA450-14 92000AA
XRA500-16 92001AA
XRA630-16 91340AA
• The fan housing shall be manufactured from
alvanised steel. Drilled flanges shall be
g
rovided at either end of the case
p
The fan body, impeller and motor housing
•
shall be further protected from deterioration
by two coats of corrosion resistant powder
oat finish
c
Motor mounting shall be via rigid welded
•
teel rod construction and support the
s
motor at four points
• The unit shall be capable of mounting at
any angle or in any plane
The motor shall be IPX4 rated external rotor
•
ype, AC capacitor start and run and have
t
ealed for life ball bearings and inbuilt
s
thermal protection. Insulation is to class F
• Impellers shall be high efficiency, low noise
ressed steel sickle blade design
p
Rotors and impellers are to be dynamically
•
balanced to ISO 1940-1:1986 Grade G 6.3
• The roof cowl assembly shall be
anufactured in glassfibre with a UV
m
stabilised external finish
• The assembly shall include a birdguard and
holes for fixing to the roof upstand
(constructed by others)
• The fan plate and bellmouth assembly shall
be manufactured from a single steel
pressing to ensure perfect form and
uniformity of impeller tip clearance
• The fan body, impeller and motor housing
shall be further protected from deterioration
by coating with corrosion resistant powder
coat finish
The motor shall be IP54 rated on sizes 500
•
and 630mm and IP44 rated on 315 - 450mm.
external rotor motor type, AC capacitor start
and run and have sealed for life bearings
• Terminals shall be provided for connection to
an external thermal overload protection device
• Customer connection shall be conveniently
ocated in an IPX4 rated terminal box
l
ttached to the body of the fan
a
Terminals shall be provided within the
•
erminal box for connection to an external
t
thermal overload protection device
• The fans shall be suitable for use in ambient
temperatures ranging from –30°C to +60°C
inimum and higher on selected models
m
• The fan shall be fully speed controllable
sing the appropriate speed controller or 5
u
tep auto transformer (available as an
s
ncillary)
a
• Suitable for 220-240V
• Insulation rating shall be class F. Impellers
hall be high efficiency, low noise pressed
s
steel sickle design for sizes 315 to 450mm
and die cast aluminium aerofoil section for
sizes 500 and 630mm
• Rotors and impellers shall be dynamically
balanced to ISO 1940 - 1.1986 Grade G 6.3
• Customer connection shall be conveniently
positioned in a IPX4 terminal box
• The fan shall be suitable for use in ambient
temperatures ranging from -30ºC to +60ºC
and higher on selected models
• The fan section shall have an integral inlet
guard to EN294
• The fan shall be fully speed controllable
using the appropriate optional electronic
speed controller or 5 step auto transformer
• Suitable for 220-240V
Xpelair XMV
The unit is to be supplied from the Xpelair XMV
range by Applied Energy Products Ltd. Morley
, Peterborough PE2 9JJ.
ay
W
Tel. +44 (0)1733 456789
The unit shall be designed for installation in
•
the horizontal plane on a suitable roof curb
or purlin box (supplied by others)
The unit shall be designed for the extraction
•
of air with temperatures up to 100ºC
The motor shall be located out of the
•
airstream and be suitable for external
ambient temperatures from -30ºC to +40ºC
176
• The motor shall be speed controllable using
a five step transformer and DOL starter
• The models shall be available for single or
three phase operation and in 4 and 6 pole
A service isolator shall be provided on
•
the unit
The impeller shall be of aluminium
•
construction with polyamide blades
A discharge birdguard shall be provided
•
• The casing and twin wall body assembly
shall be manufactured in high density
Polyethylene and coloured RAL 9002 beige
• The unit shall be 100% recyclable
A full range of optional five step
•
transformers and starters shall be available
for all models
• Suitable for 220-240V
Page 18
Xpelair XID
The unit is to be supplied from the Xpelair XID
range by Applied Energy Products Ltd. Morley
Way, Peterborough PE2 9JJ.
Tel. +44 (0)1733 456789
Model Ref
XID100 90101AA
XID125 90102AA
XID150 90103AA
ID200 90104AA
X
XID250 90208AA
XID315 90106AA
Xpelair XIDP
he unit is to be supplied from the Xpelair XIDP
T
ange by Applied Energy Products Ltd. Morley
r
terborough PE2 9JJ.
y, Pe
Wa
el. +44 (0)1733 456789
T
Model Ref
XIDP100 91383AA
XIDP125 91384AA
XIDP150 91385AA
XIDP200 91386AA
XIDP250 91387AA
XIDP315 91388AA
• The fan housing shall be manufactured from
inc coated sheet steel with integral bell
z
outh inlet & down stream guidevanes
m
The duct connection spigot shall be 30mm
•
eep minimum to facilitate secure connection
d
of the ductwork
The fan shall be supplied complete with a
•
niversal mounting bracket
u
• The unit shall be capable of mounting at any
angle or in any plane
Motors shall be IP44 rated external rotor type,
•
C capacitor start and run and have sealed
A
or life ball bearings and inbuilt thermal
f
rotection. Insulation is to be rated to class F
p
• Impellers are to be backward curved
centrifugal and dynamically balanced to ISO
1940-1:1986 Grade G 6.3
The fan shall be suitable for use with rigid or
•
flexible ductwork
• The housing shall be manufactured in a an
impact resistant and fire retardant polymer
with integral bell mouth entry, guidevanes
and terminal connection box
• The fan shall be supplied with universal
mounting bracket. The unit shall be capable
of being mounted at any angle and in any
plane
• Motors shall be IP44 rated external rotor type,
AC capacitor start and run and have sealed
for life ball bearings and inbuilt thermal
protection. Insulation is to be rated to class F
• Impellers shall be backward curved
centrifugal, dynamically balanced to ISO
1940:1986 Grade G 6.3
• External terminal connection box
The capacitor shall be mounted out of the
•
irstream and housed within the customer
a
onnection terminal box located on the
c
an body
f
• The fans shall be suitable for use in ambient
emperatures ranging from –30°C to +50°C
t
The fan shall be fully speed controllable
•
using the XIC1 speed controller (available as
an ancillary Ref. 21858AW)
Must be suitable for 220V-240V
•
The capacitor shall be mounted out of the
•
airstream and located on the fan body
• The fan shall be suitable for use in ambient
temperatures from -30ºC to +50ºC
• The fan unit shall be fully speed controllable
using XIC1 speed controller available as
an ancillary
• Must be suitable for 220V-240V
Xpelair Xpress XPRS
The unit is to be supplied from the Xpelair
Xpress range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ. Tel. +44
(0)1733 456789
Model Ref
XPRS250 91498AA
XPRS315 91499AA
XPRS355 91500AA
XPRS355+ 91501AA
The inline fan shall have a pressure
•
characteristic up to 250% higher than a
conventional unit
• The fan shall have a steel housing with
a contoured bellmouth entry and
integrated foot
• The mixed flow fan blade shall be fabricated
and balanced on the hub assembly to G 2.5
ISO 1940. There shall be matching aerofoil
section guidevanes
The motor shall be a continuously rated
•
capacitor start and run motor with integrated
thermal overload protection
iring to the outside of the unit shall to to a
W
•
terminal box rated at IP44
The fan diameter shall be no bigger than the
•
duct in which it will be installed
• The fan shall be speed controllable using a
Five step auto transformer
• Must be suitable for 220V-240V
www.xpelair.co.uk
177
Xpelair Typical Specification
Page 19
Xpelair Typical Specification
Xpelair MinimX C XCDF
he unit is to be supplied from the Xpelair
T
inimX C range by Applied Energy Products
M
td. Morley Way, Peterborough PE2 9JJ. Tel.
L
44 (0)1733 456789
+
Model Ref
XCDF100 91502AA
XCDF125 91503AA
XCDF150 91504AA
XCDF200 91505AA
XCDF250 91506AA
XCDF315 91507AA
Xpelair LoSound C LQTC
The unit is to be supplied from the Xpelair
LoSound range by Applied Energy Products
td. Morley Way, Peterborough PE2 9JJ.
L
Tel. +44 (0)1733 456789
Model Ref
LQTC125 91989AA
LQTC150 91990AA
LQTC200 91991AA
LQTC250 91992AA
LQTC315 91993AA
LQTC355 91994AA
Pressure developing low profile inline fans
•
ith hinged ‘swing out’ motor/impeller panel
w
or periodic inspection and service access
f
Casing shall be manufactured in galvanised
•
heet metal with 20mm spigot flanges and
s
ntegral first-fit key hole mounting slots
i
• Motor shall be continuously rated two pole of
external rotor motor / fan assembly design
balanced in two planes to DIN ISO 1940.
Insulation shall be IP44 Class F with thermal
verload protection
o
• The casing shall be manufactured in
galvanised sheet metal with integral keyhole
ixing points
f
• The casing shall be lined on four sides with
40mm faced attenuation material
• The unit shall be provided with a removable
cover with quick release catches for periodic
inspection and cleaning
• External rotor motor and forward curved
centrifugal fan assembly shall be balanced in
two planes to DINISO 1940
• The motor shall be maintenance free with
sealed for life bearings, and integral thermal
overload protection
Bearings shall be lubricated for life.
•
P44 protection
I
The fan shall be fitted with a terminal box
•
ncorporating knock outs and one cable entry
i
land rated IP44
g
Must be suitable for 220V-240V
•
• The IP44 Class F capacitor start and run
motor shall be rated for continuous running
A 3m three core flexible cord shall be
•
provided with the unit
Xpelair CubeX CMAX CBXC
The unit is to be supplied from the Xpelair
CBXC range by Applied Energy Products Ltd.
Morley Way, Peterborough PE2 9JJ.
Tel. +44 (0)1733 456789
ef
Model
CBXC280S315
CBXC280S355 91509AA
CBXC315S315 91510AA
CBXC315S355 91512AA
CBXC355S315
CBXC355S355 91514AA
CBXC400S400 91515AA
CBXC400S450 91516AA
178
R
91508AA
91513AA
Unit casings shall be constructed from
•
galvanised sheet metal using a frameless
construction method. The casing shall be
double skin with the addition of 40mm of
sound attenuating insulation, the casing shall
be available with a choice of two spigot sizes
for adaption to site ductwork
an shall he high efficiency backward curved
F
•
with matched external rotor. The motor shall
be fitted with sealed for life bearings and be
fitted with Thermal overload protection to the
terminal block with full motor protection
through an external tripping device
Speed control shall be through an optional
•
variable voltage device
• Centrifugal impeller motor rating IP55 Class F
Page 20
Xpelair HiFlo CMAX XSFA
he unit is to be supplied from the Xpelair XSFA
T
ange by Applied Energy Products Ltd. Morley
r
ay, Peterborough PE2 9JJ.
W
el. +44 (0)1733 456789
T
Model Ref
XSFA100 91389AA
XSFA125 91390AA
XSFA150 91391AA
XSFA200 91392AA
XSFA250 91393AA
XSFA315 91394AA
XSFA315+ 91395AA
XSFA400 91396AA
XSFA400+ 91397AA
Xpelair ManCoolers
Unit casings shall be manufactured from best
•
uality galvanised sheet steel with access
q
rom top or bottom
f
• Reinforced slotted safety fixing points shall
be incorporated to facilitate drop-rods or
mounting bolts within overall unit width
All permanent fixings shall be rivetted and all
•
emovable items shall be retained via
r
etscrews and nutserts
s
Acoustic insulation shall be self adhesive
•
oam construction meeting Class 0 rating
f
to BS476 Parts 6 and 7 to minimise
noise breakout
• Fans shall be single-inlet, single width, or
ouble-inlet, double-width, centrifugal type
d
ith high efficiency, low noise, forward-
w
urved, multiblade galvanised sheet steel
c
mpellers housed within galvanised steel scrolls
i
• Motor/impeller assemblies shall be statically
nd dynamically balanced, in two planes, in
a
ccordance with BS 5265, Part 1, 1979 to G2.5
a
Fans shall be mounted individually onto fan
•
ecks to facilitate easy removal
d
Motors shall be totally enclosed, high-
•
efficiency, split-capacitor type with power
factors of better than 0.9. Maximum ambient
operating temp. 40°C
Bearings shall be sealed-for-life,
•
aintenance-free, ball bearing type with a
m
inimum life expectancy of 50,000 hours
m
nder design operating conditions
u
Insulation shall be to Class ‘B’ or ‘F’ with
•
enclosure to IP44
• The fan shall be fully speed controllable using
the appropriate optional electronic speed
ontroller or 5 step auto transformer
c
Single fan unit
•
Must be suitable for 220V-240V
•
The unit is to be supplied from the Xpelair
ManCooler range by Applied Energy Products
Ltd. Morley Way, Peterborough PE2 9JJ.
Tel. +44 (0)1733 456789
Model Ref
ManCooler
MC350
91408AA
MC400 91409AA
MC400 110V 92309AA
MC450 91410AA
MC560 91411AA
rapeze
T
TP450 91412AA
• The floor standing units shall be supplied
complete with robust tubular stand for fast
set up on site
• The casing shall be adjustable and capable
of being locked at the desired angle of
operation
• The motor shall be totally enclosed with
maintenance free sealed for life bearings
and safety thermal overload protection
• The impeller shall comprise of a central hub
with fully adjustable high performance
blades aerofoil blades
• Finger guards to DIN24167 (UNE 20-359-
74) shall be fitted to each end of the casing
with bolted fixings
• The terminal box shall be no less than IP55
• The Trapeze model shall additionally be
available for suspension at high level using
four steel suspension eyes provided
www.xpelair.co.uk
179
Xpelair Typical Specification
Loading...