Applied Energy HBT301IS User Manual

Tumble Dryer
Instruction Book
Contents
Safety Advice 3-4 Electrical Requirements 4 Features - Get to know the main parts of your Dryer 5 Where to put and vent your Dryer 5 How to use your Dryer 6 Sorting your laundry 7 Wash Care Labels 8 Items requiring special attention 9 The Controls 10 Guide to Drying Times 11 How to Remove and Clean the Fluff Filter 12 Caring for your Dryer 12 If something goes wrong 13 If it still won’t work 14
Retention of this Instruction Book
This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use of the appliance.
If you sell or pass the appliance to someone else, or move house and leave it behind,make sure this Book is also provided so the new owner can become familiar with the appliance and safety warnings.
2
For your safety
IMPORTANT
Using your Tumble Dryer is easy.
Nevertheless, for your own safety and to get the best results it is important to know your Dryer by reading right through this handbook before using your dryer for the first time.
NEVER Allow children to play with or otherwise interfere with the dryer. NEVER Allow the air inlet at the back of the dryer,the air outlet or vent hose
to be obstructed.
NEVER ● Direct the vent hose outlet towards the air intake at the back of the
machine.
NEVER Allow the tumble dryer to recycle exhaust air. NEVER Switch the machine off leaving a hot load in the drum. NEVER Tumble dry without the filter in position. NEVER Exceed the maximum load capacity recommended or place
dripping wet items in the drum.
NEVER ● Use the dryer on a carpeted floor where the pile height would
prevent air from entering the dryer from the base.
NEVER Allow lint to collect around the dryer. NEVER Add liquid or sheet fabric conditioner to the dryer,use liquid
conditioner in the final rinse of your wash.
NEVER ● Use the dryer for commercial drying,the dryer is only suitable for
domestic use.
NEVER Dry Acrylics on the high heat setting. NEVER Tumble dry articles that have NOT been well washed in water and
detergent then well rinsed and spun.
NEVER Tumble dry articles that have had chemicals used for cleaning. NEVER Dry articles that are contaminated with flammable substances such
as: petrol,oil, paint,hair lacquer, creams, cooking fat or oil.
NEVER ● Tumble dry: rubber,foam rubber,plastic, plastic foam,nappy pants
or liners,polythene or paper. Large,very bulky items including duvets and sleeping bags.
NEVER ● Never attempt to stand on top of your dryer, it is not designed for
such use and you could injure yourself or damage the dryer by such abuse.
NEVER Switch electricity On or Off with wet hands.
IMPORTANT
A CHILD COULD CLIMB INTO OR TAMPER WITH AN UNATTENDED TUMBLE DRYER. WHEN THE MACHINE IS NOT IN USE SWITCH OFF,REMOVE THE PLUG AND CLOSE THE DOOR.
3
For your safety
ALWAYS When the dryer is not in use,switch off, remove plug,and
ALWAYS Comply with the specified electrical requirements. ALWAYS Ensure that your dryer is installed correctly and has adequate
ALWAYS Use the vent hose for optimum drying performance. ALWAYS Finish every programme with the cool tumble cycle provided on
ALWAYS Clean the filter,it is essential that the filter is kept clear of fluff
ALWAYS Observe the rules for drying garments:
ALWAYS Buy genuine accessories and spares.
close the door.
ventilation.(see “Where to put and vent your dryer”)
the control.
at all times.
In particular woollen articles should not be dried in a tumble dryer unless they are labelled ‘Superwash’, ‘Machine washable’or have the ‘May be tumble dried’ symbol: If in any doubt do not dry wool in the machine. Unlike other materials,the mechanism of wool shrinkage is irreversible,i.e. it will not stretch back to the original size and shape.
CAUTION: When the dryer is in use avoid touching the rear of the dryer as it may be hot!
Electrical Requirements
WARNING:This appliance must be earthed!
REFER TO THE RATING PLATE FOR VOLTAGE AND CURRENT REQUIREMENTS. (See diagram for location.)
The dryer should be connected to the mains supply via a suitable socket which is accessible after installing your dryer. The wires in the mains lead are coloured in accordance with the following: GREEN/YELLOW - EARTH BLUE - NEUTRAL BROWN - LIVE If a replacement plug is to be fitted, the appropriate wire must be connected to the correct terminal,the cut-off plug must be disposed of safely. DO NOT leave where it can be inserted into a socket and create a shock hazard.
Changing the mains cable
4
Should the mains lead ever require replacing at any time please contact your nearest Service Centre. A charge will be made for the replacement of the mains lead or if you require a longer lead.
The mains lead must only be replaced by a specially prepared cable obtainable from your Spares Stockist and fitted by a qualified electrician.
NOTE: IF IN DOUBT ABOUT ANY OF THE ABOVE CONSULT A QUALIFIED ELECTRICIAN.
Features - Get to know the main parts of your dryer
Mains On/Off
Heat Selector Switch
Filter Assembly
(on inside of the door)
Exhaust Air Grille
Indicator Light
(if fitted)
Timer Knob
Door Release
Where to put and vent your dryer
Your tumble dryer should NOT be located adjacent to a gas hob,cook-
er, heater, or eye level grill as flames from the burners could cause damage to your machine. The dryer should be placed where air can freely circulate around it,
preferably near a window that can be opened to reduce the possibili­ty of condensation occuring while the dryer is in use. When operating the dryer, there has to be adequate ventilation to
avoid the back flow of gases into the room from appliances burning other fuels,including open fires. A vent hose is recommended for optimum performance.
DO NOT operate the dryer in an enclosed environment, ensure
the dryer is adequately ventilated. DO NOT allow clothes, towels etc., to hang down the front of the
dryer into the airstream. This obstructs the airflow and may dam­age the dryer. Ensure that the end of the hose is not directed towards the air
intake grille at the rear of the dryer. NOTE:The vent hose should not exceed 2.4 metres in length,and
should be kept free of any possible accumulation of fluff lint (and water) by frequently shaking it out. Always ensure that the hose is not squashed.
Window Vent Kit
Wall Hanging Kit
A venting kit is available as an optional extra, which will take the moist air directly from the dryer and out through an open window. The venting kit is fitted to the front of the door.
This allows the dryer to be mounted on a wall of suitable strength to take the weight. Alternatively it should be used when the dryer is mounted on top of a work surface to secure the dryer to the wall.
WARNING:
DO NOT DISCHARGE THE EXHAUST AIR INTO A FLUE WHICH IS USED FOR EXHAUSTING FUMES FROM OTHER APPLIANCES BURNING GAS OR OTHER FUELS.
5
How to use your dryer
1. Plug in, switch on electricity.
3. Open the door. Check that the fluff filter is clean (see section How to remove and clean the fluff filter).
5. Select the relevant heat setting (see section “Sorting your Laundry”).
Push IN for full heat,for cottons, linens and syn­thetics. Low setting - button OUT for acrylics and acrylic mixtures.
6. Turn the Timer clock­wise to select the required drying time. (See Section “The Controls”.) The dryer will start
WARNING:WHEN SWITCHING ON OR OFF, PLEASE ENSURE THAT YOUR HANDS ARE DRY
2. Sort your laundry (see section “Sorting Your Laundry”)
4. Load the dryer placing the clothes carefully in the drum, pushing them well towards the back and away from the door seal. Close the door.
Button OUT
LOW HEAT
Button IN
HIGH HEAT
7. When finished open the door and take out the laundry.
Clean and replace the fluff filter.
You must terminate every programme with the Cool Tumble Phase.
6
8. Switch off electricity and remove plug from socket.
Never switch the dryer off with a hot load in the drum.
WARNING:WHEN SWITCHING ON OR OFF, PLEASE ENSURE THAT YOUR HANDS ARE DRY
Sorting your laundry
1. Always separate laundry into the correct fabric groups before washing and drying.
2. See that all zips are closed,hooks and eyes are fastened and belt, strings etc.are tied loosely in bows, you will normally have done this for each item before the washing stage.
3. It is important to extract as much water as possible from each item before drying.This saves you time and money.
WARNING:CLOTHES SHOULD NEVER BE LOADED DRIPPING WET
4. Make sure that the items to be dried are suitable for tumble drying, or are not of a type requiring ‘special attention’(see“Wash Care Labels”section).
Maximum load size
Typical load
Your dryer will hold a load of 3kg (6.6lb) dry weight of natural fabrics. if you are drying items of man-made fibres (synthetic or acrylics), the maximum load should not exceed 2kg (4.4lb) dry weight. This difference is that man-made fibres require more space to tumble-dry without creasing.
WARNING: DO NOT OVERLOAD AS THIS COULD RESULT IN REDUCED DRYING PERFORMANCE AND A POSSIBLE FIRE HAZARD.
To help you estimate how many items it takes to make up a drying load, the charts below show the approximate weights of some everyday washing items.
Clothes
Blouse Cotton 150g 5oz
Other 100g 3
Dress Cotton 500g 1lb 2oz
Other 350g 12oz Jeans 700g 1lb 6oz 10 Nappies 1000g 2lb 3oz Shirt Cotton 300g 10
Other 200g 7oz T-Shirt 125g 4
1
1
/2oz
1
/2oz
/2oz
Household Items
Duvet cover Cotton 1500g 3lb 5oz (Double)
Large Tablecloth 700g 1lb 6oz Small Tablecloth 250g 9oz Tea Towel 100g 3
Bath Towel 700g 1lb 8oz Hand Towel 350g 12oz Double Sheet 500g 1lb 2oz Single Sheet 350g 12oz
Other 1000g 2lb 3oz
1
/2oz
If you group small cotton or terry-towelling items with a synthetic fabric load they could be damp at the end of the drying cycle. If this happens simply give them an additional short period of drying to finish them off.
7
Wash Care Labels
Most of today’s fabrics can be tumble dried in your Dryer with no trouble at all, but there are certain fabric finishes which should be dried away from direct heat.
The majority of garments now have wash-care labels on them, giving full washing and drying instructions. These should always be followed carefully especially when you are drying something for the first time.
Typical symbols are:
May be tumble dried
Do not tumble dry
Or:
Tumble dry at high heat setting
Tumble dry at low heat setting
Items not suitable for tumble drying
• Those containing foam rubber or rubber-like materials or plastic
film (e.g.pillows, cushions, PVC rainwear),or any other articles which are inflammable or contain inflammable substances (e.g.towels contaminated with hair lacquer
• Fibreglass (e.g.some types of curtains)
• Items which have been dry cleaned
• Woollens.Woollen items need as much care in drying as they do
in washing.The movement of the tumble-drying action causes the woollen fibre to shrink and distort.
• Garments with the ITCL Code (see ‘Items Requiring Special
Attention’).
Do not tumble dry.
• Large bulky items e.g.continental quilts,sleeping bags, pillows,
cushions,double blankets and large bedspreads.These expand when drying and would prevent airflow through the Dryer.
WARNING: THE DRYER IS INTENDED FOR USE ONLY WHERE WATER SOLUTION IS USED FOR THE CLEANING PROCESS. MISUSE OF A TUMBLE DRYER MAY CREATE A FIRE HAZARD.
8
Items requiring special attention
Blankets and Bedspreads
Permanently pleated or creased garments
Starched articles
Fabric conditioner
The drying requirements of blankets and bedspreads will, of course, vary tremendously according to size and weight. Some, however are simply too big.if you have difficulty getting them into the Dryer,the machine will have difficulty drying them properly. Blankets (and Garments) made from Acrylic fibres (e.g. Acilan, Courtelle, Orion and Dralon) must be dried with special care on Low heat setting.Overdrying should be avoided to ensure heat creasing does not occur.
Your dryer will cope with such clothes very well, but you should always read the manufacturer’s drying instructions attached to the garment before you begin.
Starched articles should be dried together in the same load to avoid the distribution of starch to non-starched items. You should use a slightly heavier starch solution than you would when drying the items on the washing line. Make sure that as much of the solution is removed from the load as possible before placing it in the Dryer. Remove the items from the dryer as soon as they reach ironing dampness. If they are overdried the starch will powder, leaving the fabric limp - which rather defeats the purpose of the exercise!
To make sure all your tumble dried clothes come out really fresh and soft we recommend you use a liquid fabric conditioner in the final rinse of your wash. A liquid fabric conditioner restores bounce and softness and helps eliminate static cling.
Home Dry Cleaning
WARNING:ON NO ACCOUNT SHOULD LIQUID FABRIC
CONDITIONER BE ADDED TO THE DRYER ITSELF.
Garments with the ITCL Code may be cleaned using one of the Home Dry Cleaning Kits available. The instructions supplied with the Home Dry Cleaning Kit must be strictly followed.
9
The Controls
Setting the timer
Door Release
Heat Selection
Mains Light (if fitted)
Turn the Timer clockwise to select the required drying time. The drying time for both heat settings is controlled by the timer. All you have to do is turn the Timer Control clockwise slightly past the required time and then back to the required time. Do not rotate the knob beyond 120 (maximum drying time) or past the zero stop. If you have selected more time than you require turn the knob anti-clockwise to select the correct time required. This operation also starts the dryer, provided the door is closed and the machine is plugged in.The “Guide to Drying Times” section will tell you how much time you’ll need for various loads.
To open door, grip the handle and pull towards you. If the door is opened while the Dryer is in use, the drying programme cuts out automatically and the machine stops. When the door is closed the Dryer will restart but you will not need to reset the Timer Control. You can however reset the Timer Control at any stage, should you wish.
WARNING:CHILDREN HAVE BEEN KNOWN TO CLIMB INTO TUMBLE DRYERS AND INJURE THEMSELVES. ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF AT THE MAINS WHEN THE DRYER IS NOT BEING USED.
Select the appropriate button for low heat or for high heat.
With the switch IN High Heat is selected With the switch OUT Low Heat is selected
The choice of FULL HEAT or LOW HEAT depends upon the fabric you wish to dry (see section “Sorting your Laundry”)
This light indicates that there is power being supplied to the dryer when plugged into a suitable socket.
10
Guide to Drying Times
Please note that the Drying Times stated below and on appliance control panel are a GUIDE only and drying times are affected by:
The amount of water remaining in the clothes after
Items such as towelling retain a lot of water after spinning, also the suggested wash programme for small items such as T-Shirts may sometimes incorporate a low spin speed which has the same effect.
spinning
The type of fabric
Your drying load may contain the same type of fabric but of different thicknesses. Thinner items will take less time to dry. Some fabrics, such as those used for jeans are of closer texture than others and although light when dry will be heavy after washing and spinning.
The quantity of clothes to be dried
How dry you want the clothes
Single items of clothes or small loads may take disproportionally longer to dry.It is more energy efficient to dry larger loads.
As it takes longer to fully dry clothes than to have them ready for ironing, you may wish to remove some clothes when they are slightly damp,ready for ironing and then continue to dry the remainder until they are fully dry.
The heat setting you have selected
The temperature of the room
Bulky items
The label on the garment should tell you the correct heat setting to select. See ‘Wash Care Labels’.
If the room in which the dryer is situated is cold, your clothes will take longer to dry than if the room is warm.
Some bulky items such as padded jackets can be dried, with care, and we do advise that you remove these items several times, shake them and return them to the dryer. THERE ARE HOWEVER SOME ITEMS THAT WE
DO NOT ADVISE YOU TO DRY. SEE ‘ITEMS NOT SUITABLE FOR TUMBLE DRYING’
Drying Guide - approximate drying time in minutes (weights specified are when dry)
Be careful not to overdry
COTTONS SYNTHETICS ACRYLICS
High Heat High Heat Gentle Heat
Drying times 800 - 1000rpm in washing machine
Half load
1 kg
30 - 45
2 kg
45 - 55
3 kg
60 - 70
Drying times on reduced spin in washing machine
Half load
1 kg
25 - 45
Full
load
2 kg
45 - 60
Drying times on reduced spin in washing machine
Half load
1 kg
30 - 55
Full
load
2 kg
55 - 75
All fabrics contain a little natural moisture even when ‘dry’and this natural moisture should not be lost if the clothes are to remain soft and fluffy. Clothes that are dried for too long tend to wrinkle and will need more ironing than usual giving you extra work that the dryer was designed to remove.
11
How to remove and clean the fluff filter
To remove the filter
Wash or vacuum clean the filter occasionally. Don’t be alarmed by the amount of fluff you may find on the filter. It’s part of the wearing, washing and drying process.
WARNING:DO NOT OPERATE THE DRYER WITHOUT THE FILTER IN POSITION.
A very important part of your dryer is the fluff filter at the front edge of the drum. It’s there to trap the particles of lint and fluff which are normally blown away when clothes are dried on the washing-line. if the filter is allowed to become blocked, the passage of warm air through the drum will be severely restricted.This means your clothes will take much longer than normal to dry and the cost of drying them will be increased. it may also damage your dryer.
WARNING:DO NOT OPERATE THE DRYER WITHOUT CLEANING THE FILTER AFTER EACH DRYING CYCLE.
FAILURE TO CLEAN THE FILTER MAY RESULT IN A
FIRE HAZARD.
Caring for your Dryer
Your tumble dryer needs very little attention.The following simple steps will keep it performing well.
When finished
After each load
Switch off electricity and remove plug.
Always clean the filter and turn the drum by hand to check that small items like handkerchiefs do not get missed.
As necessary
Lubrication
12
Clean exterior metal and plastic surfaces with a damp cloth or silicon pol­ish only.Regularly check and clean if necessary,the vent hose and any per­manent venting fixture to ensure that there has been no accumulation of fluff or lint during the drying process. Clean fluff from the area below the fluff filter and the rear vent tube.
Do not use abrasive cleaners, scouring agents, acids, chlorine bleach or metal polish to clean any part of the machine. These could damage the machine.
Your tumble dryer uses special bearing components. Lubrication by the user is not necessary and must not be attempted.
We strongly recommend that all appliances are regularly checked for elec­trical and mechanical safety.
If something goes wrong
First, don’t panic! There may be nothing wrong at all. Look for your problem below, then check the things we suggest. More often than not, this will give you the answer to your problem, and you’ll be able to carry on without having to telephone your Service Office.
If after this you still cannot get your machine to work, follow the advice given on the next page.
Problem
‘It won’t start’
‘It is taking a long time to dry’
Any other problem
Check these things first
1. Is the machine plugged in and switched on at the socket?
2. Is the Timer Control set to required time?
3. Is the door securely closed?
4. Has the fuse blown? (Try plugging in another appliance to check)
5. Have you used an extension lead? Many are not suitable.Try
plugging the dryer directly into a socket to check.
1. Have you forgotten to clean the filter? It should be cleaned after
each load.
2. Have you selected the correct Heat setting for the type of fabric
you are drying?
3. Is the flexible Vent Hose blocked or kinked? Check it for foreign
objects or condensate (water).
4. Is the air inlet obstructed in any way?
5. Permanent venting - is flap on the storm cover obstructed?
6. Were the clothes ‘excessively wet’ when they were put in?
7. Was the correct time selected?
8. Have you overloaded the dryer?
Have you re-read this instruction book?
13
If it still won’t work...
Contact the Service Office
if something is still wrong with your machine after you’ve been through the check-list on the previous page:
1. Switch off and unplug your machine from the mains.
2. Call your nearest Service Office or local importer (outside the UK).
When you contact us we will want to know the following:
1. Your name,address and postcode.
2. Your telephone number.
3. Clear and concise details of the fault.
4. The model number and the serial number of your dryer.
5. The date of purchase enter the date here.
Please make sure you have all these details ready when you call.
Spare parts
Please remember your new appliance is a complex piece of equipment. ‘DIY” repairs or unqualified and untrained service people may put you in danger, could damage the appliance, and might mean you lose cover under the Parts Guarantee. If you do experience a problem with the appliance don’t take risks,call in our Service Engineer. Our Spare Parts are designed exclusively to fit your appliance. Do not use them for any other purpose as you may create a safety hazard.
Disposal of your product
To minimise the risk of injury to children please dispose of your product safely.The door and lid should be removed and mains cable cut off flush with the appliance ensuring that the mains plug can no longer be plugged into a mains socket.The items must then be disposed of safely.
This appliance conforms to the following EEC Directives. Low Voltage Equipment 72/23/EEC 93/68/EEC Electromagnetic Compatibility 89/336/EEC 92/31/EEC 93/68/EEC
14
PRINTED BY SIMLEX.FOUR ASHES,WOLVERHAMPTON. October 2002 Part No. 0366200003-01
Loading...