Appleton SD Series Static Discharge Grounding Reelites™ Catalog Page

SD Series Static Discharge Grounding Reelites

CONTROLS: NEC/CEC HAZARDOUS INDICATORS AND GROUNDING DEVICES

NEC/CEC:

Rated for (Unclassied) Locations

Applications

• SD Static Discharge Reelites are used for grounding portable
machines or equipment operating in hazardous atmospheres.
These Reelites safely dissipate static electrical buildup and
reduce the chance of a spark and resulting explosion.

• SD Series Reelites are spring-driven and carry various lengths
of wire cable with grounding clamps. They are applied to:
— Fuel-transfer trucks
— Barges
— Dock side loading facilities
— Grain elevators
— Hazardous maintenance areas

—Whereverammableliquidsorcombustibledustispresent

• Maximum Vdc resistance through Reelite and cable is
approximately one ohm for each 15.2 meters (50 feet) of 2.38
mm (3/32”) steel aviation control cable. On Reelites carrying 14
gauge, stranded, rubber-covered, copper cable, maximum Vdc
resistance is approximately 0.15 ohms per 15.2 meters (50 feet)
of cable.

• SD11 Series
— Lightweight, compact, enclosed, all-steel construction.
— 15.2 meter (50 foot) single or Y-type cable lengths in 3/32”

galvanized steel aviation control cable with or without nylon

jacket.
— 100 Amp universal jaw type grounding clamp.
— Gravity type ratchet.
— Mounts on ceiling, wall or with base down to a clean,

unpainted conductive surface to assure positive electrical

continuity through frame.

• SD50A thru SD100A Series
— Lightweight and compact. Rugged open drum design with all

steel construction.

— Available with cable lengths from 15.2 meters (50 feet) to

30.5 meters (100 feet), single and Y-type construction.

Standard Materials

• SD11, SD50A thru SD100A: all steel construction

Standard Finishes

• SD11 series: red epoxy powder coat

• SD50A thru SD100A Series: yellow epoxy/polyester
powder coat

Options

• An SDG grounding stud and SDP grounding plug, required
by some state regulations, provides positive grounding and
prevents accidental cable severing.

• Stainlesssteelcableisavailable,addsufx-SS

• Withoutratchet,addsufx-LR

™

SD11 Series

SD50A thru SD100A Series

SDG

Permanent grounding stud

for 2.38 mm (13/32”) hole.
Thread 3/8 — 16 UNC-2B.

SDP

Positive grounding plug.

Without cord.

Note:
 An SDG grounding stud and SDP grounding plug, required by some state regulations, provides positive grounding and prevents accidental cable severing. See

next page for part numbers.

344

SD Series Static Discharge Grounding Reelites

CONTROLS: NEC/CEC HAZARDOUS INDICATORS AND GROUNDING DEVICES

NEC/CEC:

Rated for (Unclassied) Locations

™

Description Catalog Number

15.2 meters (50 feet) of 2.38 mm (3/32”) galvanized steel aviation control cable. 1 ohm
D.C. resistance.

15.2 meters (50 feet) of 2.38 mm (3/32”) nylon covered galvanized steel aviation control
cable. 1 ohm D.C. resistance.

15.2 meters (50 feet) total cable length consisting of 10.7 meters (35 feet) of 2.38 mm
(3/32”) galvanized steel aviation control cable branching out to two 4.6 meters (15 feet)
lengths with grounding clamps. 1 ohm D.C. resistance.

15.2 meters (50 feet) of 2.38 mm (3/32”) galvanized steel aviation control cable. 1 ohm
D.C. resistance.

15.2 meters (50 feet) of 2.38 mm (3/32”) galvanized-steel cable with 1/64” nylon jacket.
1 ohm D.C. resistance.

30.5 meters (100 feet ) of 2.38 mm (3/32”) galvanized steel cable with 0.40 mm (1/64”)
nylon jacket. 1.5 ohm D.C. resistance.

30.5 meters (100 feet ) of 2.38 mm (3/32”) galvanized steel aviation control cable. 2
ohms D.C. resistance.

22.9 meters (75 feet) total cable length consisting of 15.2 meters (50 feet) of 2.38 mm
(3/32”) galvanized steel aviation control cable branching out to two 7.6 meters (25 feet)
lengths with grounding clamps. 1.5 ohms D.C. resistance.

SD11

SD11N

SD11Y

SD50A

SD50AN

SD100AN

SD100A

SD75AY

30.5 meters (100 feet) total cable length consisting of 22.9 meters (75 feet) of 2.38 mm
(3/32”) galvanized steel aviation control cable branching out to two 7.6 meters (25 feet)
lengths with grounding clamps. 2.0 ohms D.C. resistance.

Permanent Grounding Stud for 2.38 mm (3/32”) hole. Thread 3/8-16 UNC-2B. SDG

Positive Grounding Plug. Without cord. #14 Type ”S” 0.265 max. SDP

SD100AY

345