Appleton Instruction Sheet: Stylmaster Strobe Luminaires, 650400001 | Appleton Manuals & Guides

Description

The Stylmaster signaling appliances are intended
for general utility signaling use. The strobes are
available in pendant, bracket or ceiling mount
configurations and in 120V 60 Hz and 240V 60
Hz. The beacons are UL and cUL Listed for use
in Class I, Division 2, Group A, B. C and D haz­ardous locations; pendant-mount versions are
also Listed for Class II, Division 1, Group E, F
and G; Class II, Division 2 Group F and G; and
Class lIl Division 1 and 2 hazardous locations.
Operating Temperature Codes are per the follow­ing chart.

Temperature Codes

NOTE: Class II and Class III Listings

only apply to Pendant Mount

wire leads through the 3/4" (19 mm) NPT threaded
conduit (not supplied). Secure the 3/4" (19 mm)
threaded conduit to the mounting hood.

Ground the unit in accordance with National
Electrical Code (NFPA 70) and local requirements.

Connect red positive (+) wire lead to incoming
positive (+) and connect black negative (-) wire
lead to incoming negative using wire nuts (not
supplied).

Secure the 3/4" (19 mm) threaded conduit to the
outlet box.

2. Bracket Mount Models (Figure 2): Remove
the outlet box from the end of the mounting
bracket. Install the outlet box using appropriate
hardware (not supplied) for the mounting sur­face. Pull the field wiring through the outlet box.

Ground the unit in accordance with National
Electrical Code (NFPA 70) and local requirements.

Connect red positive (+) wire lead to incoming
positive (+) and connect black negative (-) wire
lead to incoming negative using wire nuts (not
supplied).

Mount the wall bracket back onto the outlet box.

3. Ceiling Mount Models (Figures 3 and 4):
Unscrew and remove the clear outer globe.
Remove the two screws holding the circuit
assembly to the bottom of the fixture. To separate
the ceiling junction box from the fixture housing,
remove the remaining two screws at the bottom
of the fixture.

Mount the ceiling junction box using appropriate
hardware. Pull power source wiring through the
ceiling junction box.

Ground the unit in accordance with National
Electrical Code (NFPA 70) and local requirements.

Connect the positive (+) power source wire to the
positive (+) terminal and the negative (-) power
source wire to the negative (-) terminal.

They are UL and cUL listed as Type 3R and 4.
AC rated strobes are also UL and cUL Listed
and Marine Rated.

The strobe flashes a 360-degree beam of light
approximately 65 times per minute.

EGS Electrical Group • 7770 N. Frontage Rd. • Skokie, IL 60077 Rev. A 650400-001 9/7/00 Page 1

Install this unit in accordance with the applicable
requirements in the latest edition of the National
Electrical Code or Canadian Electrical Code,
using supply wire rated per Table 2.

1. Pendant Mount Models (Figure 1): Install explo­sion-proof hanger box (not supplied). Pull the unit's

650400-001

Installation Instructions for Stylmaster Strobe Light

for Use in Hazardous Locations

Ambient Class I, Div. 2 Class II, Div. 1 & 2

Temp. Groups A, B, C & D Class III, Div. 1 & 2

40˚C 280˚C (T2A) 120˚C (T4A)

55˚C 300˚C (T2) 135˚C (T4)

65˚C 300˚C (T2) 135˚C (T4)

WARNING

To reduce the risk of ignition of hazardous
atmospheres and shock, do not apply power
to the unit until installation has been complet­ed and unit is tightly assembled and secured.

!

4. Where applicable, install the optional guard
assembly over the clear outer globe and secure
using three screws (provided).

Maintenance

Disassemble the unit as follows (Figure 4):

1. Where applicable, remove the guard by

rotating counterclockwise

2. Unscrew and remove the clear outer globe.

3. To replace the strobe tube, remove the inner

lens and replace the appropriate tube as listed in
Ta ble 1.

4. Reinstall the inner lens. Screw the clear outer
globe back onto the fixture housing.

5. Where applicable, install the guard assembly
over the clear outer globe by rotating clockwise
until it snaps into place.

Figure 2. Detail of Bracket Mounting.

Page 2 Rev. A 650400-001 9/7/00 EGS Electrical Group • 7770 N. Frontage Rd. • Skokie, IL 60077

Figure 3. Detail of Ceiling Mounting.

Figure 1. Detail of Pendant Mounting.

Secure the fixture housing on the junction box
by replacing the two screws removed above.
Reinstall the circuit assembly to the bottom of
the fixture using the two screws removed above.

Screw the clear outer globe back on the fixture
housing.

WARNING

To reduce the risk of ignition of hazardous
atmospheres and shock, keep assembly tight­ly closed when circuits are energized.

!

WARNING

To reduce the risk of ignition of hazardous
atmospheres and shock, keep assembly tight­ly closed when circuits are energized.

To reduce the risk of ignition of hazardous
atmospheres and shock, disconnect from the
supply and circuit and allow five (5) minutes
for stored energy to dissipate before disas­sembling the unit.

!