Appleton Instruction Sheet: Mercmaster LED Low Profile Luminaires to Crouse-Hinds Champ Series Mounting Hoods | Appleton Manuals & Guides

650518-000 INSTRUCTION SHEET

Installation Instructions for Mercmaster™ LED Low Profile Luminaires
to Crouse-Hinds Champ Series Mounting Hoods

FOR PROPER & SAFE INSTALLATION OF THESE PRODUCTS, PLEASE READ
THE FOLLOWING INSTRUCTIONS.

Applications

• Marine and wet locations.

• Areas where ammable gases and vapors are present under conditions dened by the ratings below.

• Areas of low clearance, low ceiling heights, or where luminaire weights must be minimized.

• Non-hazardous locations where severe weather conditions, excessive moisture, dirt, dust, corrosive atmospheres and
high ambient temperatures are encountered.

Agency Ratings

• Class I, Div. 2, Groups A, B, C and D

• Class I, Zone 2, Group IIC

• Class II, Div. 2, Groups F & G

• Class III

• Type 3R, 4 and 4X

• Wet Locations

• Marine outside type (salt water) NOTE: For U.S. applications only.

Product Safety

Signal Words Defined

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous

situation which, if not avoided, could result in death or serious injury. CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury. NOTICE is used to address practices not related to physical injury.

Safety Instructions

WARNING: Do not open or remove the luminaire with the circuit energized.

WARNING: Do not use this luminaire on ungrounded systems. Failure to ground the luminaire can result in an electric shock,

which may be fatal.

WARNING: Do not use on ungrounded 480 Volt circuits.

CAUTION: Do not look directly at the LEDs when energized.

NOTICE: Do not touch the LEDs; touching could leave oily deposits, causing hot spots and potential premature failure.

NOTICE: When installing in a hazardous location, it is necessary that the globe and all conduit plugs are tightly secured and all

luminaire ttings (mounting hood, adaptor hood and luminaire) are tightly secured together to prevent water and dust entry. The
globe should be cleaned periodically to maintain lighting efciency.

NOTICE: This luminaire is designed for and should be installed in accordance with the National Electrical Code®/Canadian

Electrical Code and all local codes.

Appleton • 1.800.621.1506 • www.appletonelec.com 650518-000 Rev. B 08/16 • Page 1 of 4

Application:

The Mercmaster LED Low Prole adaptors are designed for use where Crouse-Hinds Champ Luminaire mounting hoods are installed
and where Appleton Electric Mercmaster LED Low Prole Luminaires are needed. The MMAD-CHVS and MMAD-CHVA adaptors
make for a simple conversion to the Appleton Mercmaster LED Low Prole Luminaire family without opening the conduit system. The
MMAD-CHVS and MMAD-CHVA mounting hood adaptors will accept the following Appleton Electric Company Luminaires:

• MLLED Series 2, 3 or 4.

The MMAD-CHVS adaptor is compatible with the following Crouse-Hinds Champs Series mounting hoods from the Champ Series
product lineup:

• DMV Series:
Ceiling Hoods - Cat. No.’s CM2, CM3
Pendant & Flexible Pendant Hoods – Cat. No.’s APM2, APMS, HPM2
Quad Hoods – Cat. No. QM25

The MMAD-CHVA adaptor is compatible with the following Crouse-Hinds Champs Series mounting hoods from the
Champ Series product lineup:

• DMV Series:
25° Stanchion Hoods - Cat. No. JM5
90° Stanchion Hoods – Cat. No. PM5
Wall Hoods – Cat. No.’s TWM2, TWM3

NOTE: The MMAD-CHVS and MMAD-CHVA Appleton mounting adaptors are not to be used with Crouse-Hinds Champs Series
mounting hoods provided with fuses and fuseholders.

Installation:

1. Make certain that the Crouse-Hinds Champ Series luminaire has been de-energized before any changes are made to the system.

2. Remove the Crouse-Hinds Champ Series luminaire from its mounting hood according to the Crouse-Hinds removal instructions

provided with the original xture assembly. Questions concerning the removal of the Crouse-Hinds products should be directed
towards Crouse-Hinds customer service. Inspect the Crouse-Hinds mounting hood sealing surfaces for any damage.

3. Ensure that the sealing surfaces are clean and free of debris. Wipe with a damp cloth and then dry fully before installation.

4. Refer to Figure 1 showing Crouse-Hinds Champ Series hoods. Install the Appleton MMAD-CHVS or MMAD-CHVA mounting

adaptor onto the Crouse-Hinds Champ Series hood by capturing the hood’s hinge and bringing the Appleton mounting adaptor
carefully up to the sealing surface of the hood. Make sure to allow the xture wiring to safely come through the adaptor hood large
hole when the luminaire housing sets against. Make sure the wiring includes a ground wire. Tighten down the adaptor hood screw
securely to lock in place.

FIGURE 1 - CROUSE-HINDS CHAMP SERIES HOODS

650518-000 Rev. B 08/16 • Page 2 of 4Appleton • 1.800.621.1506 • www.appletonelec.com