Appleton Instruction Sheet: Contender LED Series Luminaires with Wire Nuts 650583-000 | Appleton Manuals & Guides
650583-000 INSTRUCTION SHEET
Installation Instructions for Appleton™ Contender™ LED Luminaire
FOR PROPER AND SAFE INSTALLATION OF THIS PRODUCT, PLEASE READ THE FOLLOWING INSTRUCTIONS.
Product Safety
Signal Words Defined
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous
situation which, if not avoided, could result in death or serious injury. CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury. NOTICE is used to address practices not related to physical injury.
Safety Instructions for Complete Luminaire
WARNING
• Do not open or remove the luminaire with the circuit energized.
• Do not use this luminaire on ungrounded systems. Failure to ground the luminaire can result in an electric shock, which may be fatal.
• Before installation, ensure that the unit complies with the hazardous area classication. Refer to luminaire nameplate, located on
exterior of housing body, for suitability in specic hazardous locations.
• Do not use on ungrounded 480 volt circuits.
• Do not open when explosive atmospheres are present.
• Beware of electrostatic charges. Use a moist cloth to clean polycarbonate globe.
• Supply wires are to be rated for minimum 90°C.
CAUTION:
• Do not look directly at the LEDs when energized.
• Disconnect the luminaire from the supply circuit before opening to reduce the risk of ignition in hazardous atmospheres.
• It is necessary that the globe and all conduit plugs are tightly secured and all luminaire ttings (mounting hood and optic) are tightly
secured to the LED housing to prevent water and dust entry. The optic should be cleaned periodically to maintain lighting efciency.
NOTICE:
• Do not touch the LEDs; touching could leave oily deposits, causing hot spots and potential premature failure.
• This luminaire is designed for and should be installed with hazardous locations wiring method required in accordance with the
National Electrical Code®/Canadian Electrical Code and all applicable local codes.
• This product must be installed in accordance with the applicable installation code by a person familiar with the construction and
operation of the product and hazards involved.
• Do not use this equipment for anything other than its intended use.
Applications/Intended Use
• To reduce the risk of ignition of hazardous atmosphere, disconnect the luminaire from the supply circuit before opening. Keep
tightly closed when in operation.
• Areas where ammable gases and vapors are present under conditions dened by the ratings below.
• Areas of low clearance, low ceiling heights, or where luminaire weights must be minimized.
• Non-hazardous locations where severe weather conditions, excessive moisture, dirt, dust, corrosive atmospheres, and
high ambient temperatures are encountered.
Agency Ratings j
• Class I, Division 2, Groups A, B, C, D • Wet Locations
• Class II, Division I, Groups E, F, G • Marine Outside Type (Salt Water) for USA only
• Class II, Division 2, Groups F, G • Type 3R, 4, 4X
• Class III • IP66/67
• Simultaneous Exposure
NOTES:
j Refer to product nameplate, located on the exterior of the housing body for details.
To be installed in accordance with CG-259 of American Bureau of Shipping and Coast Guard.
Appleton • 1.800.621.1506 • www.appletonelec.com 650583-000 Rev. C 02/25/19 • Page 1 of 8
Luminaire Dimensions
FIGURE 1: CONTENDER LED LUMINAIRE
650583-000 Rev. C 02/25/19 • Page 2 of 8Appleton • 1.800.621.1506 • www.appletonelec.com
LED Housing Installation
Canadian Electrical Code (Rule 30-500 and Section 10). Verify that ground continuity has been established by using an Ohm meter
or other suitable test equipment before energizing the luminaire. Failure to properly ground the luminaire will create an electric shock
hazard, which can cause serious injury or death.
This product is intended to be used with Eaton Crouse-Hinds Champ series mounting hoods. It is up to the installer to ensure that
the Crouse-Hinds mounting hood that this product is being installed on is in good condition and will mate with the luminaire properly.
Installer must ensure that the gasket is compressed properly against the Crouse-Hinds hood all the way around the luminaire.
Once this product is installed to a compatible Crouse-Hinds mounting hood it may not be removed from the hood as this is a
non-serviceable joint. To service the xture the three captive bolts from the top side of the xture may be removed to access the
electronic driver.
WARNING: The luminaire must be grounded as required by the National Electrical Code (Paragraph 410-21 and Article 250) or
FIGURE 2: WIRING COMPARTMENT
1. Disconnect facility power to the electric power supply leads.
2. Hang the LED housing on the hinge as shown in the gure above.
3. Connect the electric power supply leads to the cord that comes out of the luminaire. 12 inches of cord is provided from the top of
the xture with stripped leads. If less cord is required the installer may cut shorter and re-strip wires.
4. Make sure hood is grounded to the luminaire by attaching ground wire to the cord provided.
5. Once wired, swing luminaire into position and tighten the captive bolt into the Crouse-Hinds hoods until the luminaire and mounting
hood bottoms out.
650583-000 Rev. C 02/25/19 • Page 3 of 8Appleton • 1.800.621.1506 • www.appletonelec.com
Loading...