RE Series Recessed and Surface Mounting Fluorescent Luminaires
Standard and Emergency Back-Up. Increased Safety
ATEX/IECEx:
Zone 1 and 2 - 21 and 22
II 2 GD
IP66 - IK09/10
Applications
• Designed for ush or surface mounting; most specically
clean room environments where a seamless smooth ceiling is
mandatory.
• Typical applications include: the food industry, chemical plants,
pharmaceuticals and delicate electronic manufacturing such as
the aerospace industry.
• Ideal for use in rigorous corrosive environments, involving water,
dust and extreme temperature variations.
• Can be installed in hazardous areas designated as Zone 1 and
2 – 21 and 22.
Features
• One piece welded steel housing with integral frame to seal out
contaminants.
• Allows recessed mounting in permanent ceilings from 55 mm to
130 mm (2.17 to 5.12 in).
• Frameless tempered 5 mm (1/4 in) thick lens. Lens secured to
housing by internal metallic hinges and secured with captive
316L stainless steel screws, allowing for easy lamp replacement
and xture maintenance.
• Positive safety switch and Ex e battery with plug-in connector
for safety and easy maintenance in hazardous locations.
• Designed for ease of installation and maintenance.
• Bi-pin G13 lampholder.
• Also available as surface mounting version.
• New ballast:
— EOL (End Of Life) protection in accordance to the latest EN
60079-7 standard
— Multi-tap 110 to 254 Vac/Vdc +/-10% 50/60 Hz
— Two channel standard ballast (if one lamp fails the second
lamp remains in operation)
— Ex e plug-in connector for rapid and error free maintenance
— Self test on 3 hours duration emergency version
— High power factor electronic ballast (>0.95)
• Cable entries:
— Three clearance holes for M20 cable gland supplied with M20
polyamide cable gland — cable diameter 6.5 to 14.5 mm
(0.26 to 0.57 in) — and M20 polyamide blanking plug. See Standard Cable Entry Accessories on following pages.
— One M6 earth stud.
Standard Materials
• Housing and integral frame: one piece, welded steel
• Safety lens: 5 mm (0.20 in) thick tempered
• Gasket: silicone, 4 lips, completely sealed and contained in the
xture
• Internal reector: white polycarbonate multi-parabolic
• Cable gland and blanking plug: polyamide
Standard Finishes
• Housing and integral frame: white powder epoxy paint
Options
• 3 hours emergency version - Battery 6 V - 4 Ah. Add sufx -E.
RE Series Recessed and Surface Mounting Fluorescent Luminaires
Standard and Emergency Back-Up. Increased Safety
ATEX/IECEx:
Zone 1 and 2 - 21 and 22
II 2 GD
IP66 - IK09/10
Recessed — 110/254 Vac/Vdc, 50/60 Hz — Front Access — White Painted Steel Housing
VersionReflectorWiring
Standard Version — Bi-pin Lamps (G13)
2 x 18 WPolycarbonate
4 x 18 WWhite Painted Steel
2 x 36 WPolycarbonate
4 x 36 WWhite Painted Steel
2 x 58 WPolycarbonate
4 x 58 WWhite Painted Steel
3 Hours Emergency Version — Bi-pin Lamps (G13)
2 x 18 WPolycarbonate
4 x 18 WWhite Painted Steel
2 x 36 WPolycarbonate
4 x 36 WWhite Painted Steel
2 x 58 WPolycarbonate
4 x 58 WWhite Painted Steel
Loop14 (30.86)64 (3905.52)REB218BUFL
Through14 (30.86)64 (3905.52)REB218BUFT
Loop21 (46.30)93 (5675.21)REB418BUFLP
Through21 (46.30)93 (5675.21)REB418BUFTP
Loop19 (41.89)108 (6590.56)REB236BUFL
Through19 (41.89)108 (6590.56)REB236BUFT
Loop29 (63.93)158 (9641.75)REB436BUFLP
Through29 (63.93)158 (9641.75)REB436BUFTP
Loop22 (48.50)130 (7933.09)REB258BUFL
Through22 (48.50)130 (7933.09)REB258BUFT
Loop32 (70.55)190 (11594.51)REB458BUFLP
Through32 (70.55)190 (11594.51)REB458BUFTP
Loop14 (30.86)64 (3905.52)REB218BUFLEP
Through14 (30.86)64 (3905.52)REB218BUFTEP
Loop21 (46.30)93 (5675.21)REB418BUFLEP
Through21 (46.30)93 (5675.21)REB418BUFTEP
Loop19 (41.89)108 (6590.56)REB236BUFLE
Through19 (41.89)108 (6590.56)REB236BUFTE
Loop29 (63.93)158 (9641.75)REB436BUFLEP
Through29 (63.93)158 (9641.75)REB436BUFTEP
Loop22 (48.50)130 (7933.09)REB258BUFLE
Through22 (48.50)130 (7933.09)REB258BUFTE
Loop32 (70.55)190 (11594.51)REB458BUFLEP
Through32 (70.55)190 (11594.51)REB458BUFTEP
Weight
kg (lb)
Volume
3
dm
(in3)
Catalog Number
For surface mounting lighting, replace letter F with letter M in the 9th position; example: REB218BUML.
For 3 hours emergency version - Battery 6 V - 4 Ah, add suffix E to the end of the catalog number; example: REB218BUFLE.
For 1 hour 30 emergency (combined) - Battery 6 V - 7 Ah, add suffix E1 to the end of the catalog number; example: REB218BUFLE1.
For 3H Emergency (combined) - Battery 6 V - 7 Ah, add suffix E7 to the end of the catalog number; example: REB218BUFLE7.
For fixture without a safety switch, add suffix N to the end of the catalog number; example: REB218BUFLN.
For fixture with a white painted steel internal reflector, add suffix P to the end of the catalog number; example: REB218BUFLP.
For fixture with 316L stainless steel housing and integral frame and natural finish, add suffix S to the end of the catalog number; example: REB218BUFLS.
538
Page 5
™
FLUORESCENT/AREA: ATEX/IECEx STANDARD AND EMERGENCY BACK-UP