TM
iOS
FCC Statement
This device compiles with Part 15 of the FCC rules.
Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
according to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communication. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
Personal
Cloud Storage
reception, which can be determined by turning the
equipment off and on, the user is encourage to try
to correct the interference by one or more of the
following measures:
1.Reorient the receiving antenna.
2.Increase the separation between the equipment
and receiver.
3.Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
4.Consult the dealer or an experienced radio/TV
technician for help.
Caution: Any changes or modifications not
expressly approved by the party responsible for
compliance could void your authority to operate
the equipment.
802.11 b/g/n
Wi-Reader
7
Power bank
(External Battery)
1
2
3
4
5
6
USB Flash Drive
& SD card
Location of Controls
Pro
Android
iOS
Free App
Android
1. Wi-Fi Indicator
2. Card/Drive Indicator
3. Charging Indicator
4. Power Indicator
7
5. SD Card Slot
8
6. USB Port
9
7. RJ-45 Jack
10
8. Micro USB Port
9. Reset Button
10. Function Switch
Charging the Wi-Reader Pro
When the Power indicator is orange, it is time
to charge the battery. To charge this unit, simply
connect the small end of the supplied Micro USB
cable to the Micro USB port on this unit and the
other end to a powered USB port on a computer
or to a USB Power Adapter (Not included). While
charging, the charging indicator will light red.
When fully charged, the charging indicator
will turn off.
Using the Wi-Reader Pro as a Card Reader
iOS (Shown in blue)
Text in blue pertains to the Apple Device only.
Screens may vary slightly depending on the Apple device you are
using.
1.Download the Wi-Reader App from the Apple App Store.
2.Insert an SD Card into the SD card slot or insert a Flash drive into
the USB port.
Charging an Apple or Android Device
To charge an Apple or Android device, simply
plug the cable from the external device’s
charging port to the USB port on the Wi-Reader
Pro. Then slide the Function switch to the Charge
position; the external unit will be charged.
Android (shown in green)
Text in green pertains to the Android only.
Screens may vary slightly depending on the Android device you are using.
1.Download the Wi-Reader Pro App from the Google Play Store.
2.Insert an SD Card into the SD card slot or insert a Flash drive into the USB port.
3.Slide the Function switch to the position; after a short while, the indicator
will blink blue and the Wi-Reader Pro will be available. Enter the Settings on your
device, then Wi-Reader Pro_xxxxxx (x represents random digits).
3.Slide the Function switch to the position; the Power
indicator will light and after a short while, the indicator will
blink blue and the Wi-Reader Pro will be available. Tap the
Settings App on your i-device, then select Wi-Fi. From this Wi-Fi
list, select Wi-Reader Pro_xxxxxx (x represents random digits).
4.Tap the Wi-Reader App to open the App. You will see five
items: Videos, Photos, Music, Documents and Folder View.
Select Folder View to view contents of SD card or Flash drive, or
select one of the options to view the contents. See below for
valid format.
Video: M4V, MP4, MOV
Photos: JPG, BMP, PNG
Music: MP3, WAV, AAC
Documents: PDF, DOC, PPT, TXT, HTM, XLS, KEY, PAGES,
NUMBERS
5.Tap one of the files and it will play/appear in the Wi-Reader
App. If you try to play a non-valid file, “Unable to Open” will
appear on the screen.
6.What Else Can You Do With Files:
While a list (music, photo, etc.) appears, tap on one of the
option, for example Photos, tap Edit, tap on the desired file and
then click the icon. This will bring up buttons which
perform the following functions:
Save to Library (Photos only): Tap to save the photo to your
device’s photo library.
Download: Tap to download the file into your Collections.
Move: Tap to move files.
Export: Tap to export the file into other App.
Rename: Tap to rename the file.
Delete: Tap to delete the file.
Cancel: Tap to cancel.
4. Tap the Wi-Reader Pro App to open the App. You will see five
items: Videos, Photos, Music, Documents and Folder View.
Select Folder View to view contents of SD card or Flash drive, or
select one of the options to view the contents. See below for valid
format.
Video: Please download MX Player or MoboPlayer to watch videos
on this App.
Photos: JPG, BMP, PNG
Music: MP3, WAV, AAC
Documents: PDF, DOC, PPT, TXT, HTM, XLS
Note: For HTC/Samsung Phone, please use the build-in Polaris
Office App. For other Android phones, please download OliveOf-
fice.
5.Tap one of the files and it will play/appear in the Wi-Reader Pro
App. If you try to play a non-valid file, “no app support” will
appear on the screen.
6.What Else Can You Do With Files:
While a list (music, photo, etc.) appears, tap on one of the option,
for example photos, tap the icon (top right), tap on the desired
file and then click the icon (top left). This will bring up
buttons which perform the following functions:
Download: Tap to download the file into your Collections.
Export: Tap to export the file into other App.
Rename: Tap to rename the file.
Move: Tap to move fies.
Delete: Tap to delete the file.
Cancel: Tap to cancel.
Viewing or Uploading Files in Your Collections
iOS
1.Open the Wi-Reader App as previously described. Tap the
Collections icon at the bottom of the screen and the Collections
screen will appear.
2.If any files have been saved to your collection, simply tap on
one to play/view it in the Wi-Reader App.
3.To Upload a file from your photos on your device to an SD
card/flash drive, tap Upload From Camera Roll. Select photo(s)
then tap Done. Select where to upload the files to, then tap
Done and the unit will upload the files.
4.While in the Collection’s list, tap the Edit button at the top
right to bring up the icons at the bottom of the screen.
Select a file, then tap the icon. This will bring up a screen
that will allow you to Upload, Move, Export, Rename, Delete or
Mail the selected file.
Tap to create a new folder.
Tap to select all files.
Tap to sort the files, either by Name, Type or Date.
Android
1.Open the Wi-Reader Pro App as previously described. Tap the
Collections icon at the bottom of the screen and the Collections
screen will appear.
2.If any files have been saved to your collection, simply tap on
one to play/view it in the Wi-Reader Pro App.
3.To Upload a file from your device to an SD card/flash drive,
tap Upload From Smartphone. Select file(s) then tap Choose
target folder then tap Upload and the unit will upload the files.
4.While in the Collection’s list, tap the icon (top right),
tap on the desire file and then click the icon (top left). This
will bring up options which allow you to Upload, Export,
Rename, Move or Delete the selected file.
5.While in the Collection’s list, tap the icons to perform the
following functions:
Tap to create a new folder.
Tap to sort the files, either by Name, Type or Date.
Creating a Wi-Fi Hotspot (Similar procedure for iOS or Android Device)
Illustrations are of the iPhone, but the other iOS and Android screens are very similar.
1.Plug internet cable into RJ-45 jack. It is recommended to
keep the Wi-Reader Pro connected to the computer; or a
USB power adapter.
2.Slide the Function switch to the position; the power
indicator will light and after a short while, the indicator
will blink blue and the Wi-Reader Pro will be available. Tap
the Settings App on your iOS device, then select Wi-Fi (on
Android, go to Wi-Fi setting). From this Wi-Fi list, select
Wi-Reader Pro_xxxxxx (x represents random digits).
3.Open the device’s browser then enter “10.10.1.1” in
the space provided for the URL.
4.Select Settings at the top right of the screen.
6.If connecting through a hotel room’s internet
connection, select DHCP from the WAN Access Type
pull down menu.
If connecting through ASDL modem, select PPPoE
from the WAN Access Type pull down menu and enter
your username/password. Tap Next.
7.At the Wireless Basic Setting screen, you can change
the SSID of Wi-Reader or tap on Next to continue.
8.At the Wireless Security Setup screen, you can set
the password of the Wi-Fi here then tap Finished.
The Wi-Reader Pro will reboot. You may have to
change the Wi-Reader Pro will reboot. You may have
to change the Wi-Fi to the Wi-Reader Pro_xxxxxx
again.
5.Select Gateway and then tap Next. At the next LAN
Interface screen, tap Next again.
Settings
Tap the Settings icon at the bottom right of the screen to
bring up the Setting screen. The items listed on this screen
perform the following:
App Version: This is App version.
About Wi-Reader: If connected to the internet, tap this to
see more info about the Wi-Reader.
Send Feedback: Tap to send feedback about Wi-Reader or
the Wi-Reader app.
Device Setting: Tap to enter the Wi-Fi password and/or
change the Wi-Fi SSID.
Connect Setting (iOS only): Used by iOS, you will not need
this unless instructed.
Clean Thumnail Cache: Tap to clean the Thumbnail Cache
which takes space on your device.
Check storage Space: Tap to view the sda 1 Free Space and
the Collection files Used Space.
Logout (Android only): Tap to log out.
iOS
Android
Wi-Fi Repeater
This unit can also be used as a Wi-Fi Repeater. This feature will allow you to extend
the signal by receiving the signal and then sending it out again, thus extending the
Resetting the Wi-Reader Pro
If you are having trouble or experiencing erratic
operation with the Wi-Reader Pro, the blue light
flash while operating Wi-Reader Pro, follow the
instruction below.
Insert a pin or similar pointed object into the Reset
button, hold 3-4 seconds, until the blue light stop
flashing. This will reset the Wi-Reader Pro.
Contacting Us
If you have any trouble, please try resetting the unit as describe above. If that does
not work, you can contact us using the Send Feedback option in the Setting or
visiting www.carry.com.tw
Loading...