Aplex ARCDIS-107 User Manual

1

ARCDIS-1xx

User Manual

7”,10.1”, 12.1”, 15” front panel IP65 aluminum die-casting chassis Display

Release Date Revision

Oct. 2014 V1.4

® 2014 Aplex Technology, Inc. All Rights Reserved. Published in Taiwan

Aplex Technology, Inc.
15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan
Tel: [phone] Fax: [phone] E-mail: [e-mail]
URL: www.aplex.com.tw

ARCDIS-1XX User Manual

2

Warning!_______________________________

This equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions manual, it may cause interference to radio
communications. It has been tested and found to comply with the limits for a Class A computing
device pursuant to FCC Rules, which are designed to provide reasonable protection against
such interference when operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference in which case the user at his own expense will be
required to take whatever measures may be required to correct the interference.

Electric Shock Hazard – Do not operate the machine with its back cover removed. There are
dangerous high voltages inside.

Disclaimer

This information in this document is subject to change without notice. In no event shall Aplex
Technology Inc. be liable for damages of any kind, whether incidental or consequential, arising
from either the use or misuse of information in this document or in any related materials.

ARCDIS-1XX User Manual

3

Table of Contents______________________

Warning!…………………………………………………………………………….……..….2
Disclaimer………………………………………………………………….…………………2

Chapter 1 Getting Started

1.1 Features……………………………………………………………………….5

1.2 Specifications…………………………………………. ...……………...….5

1.3 Dimensions…...………………………………...………………………….…7

1.4 Brief Description of ARCDIS-1XX ……………..………………………….11

1.5 Display Mode………………………………………………………………..15

Chapter 2 OSD

2.1 AD Board OSD Functions………………………….…..……………….….16

2.2 OSD Controls………………………………………………………………..17

2.3 OSD Functions…………………………………………………………...…18

2.4 OSD Default Parameter…………………………………………………....18

2.5 Main Menu…………………………………………………………………..19

Chapter 3 Installation

3.1 Introduction to the PenMount 9036 Controller Board.……………….….22

3.2 Features……………………………………………………………………..22

3.3 Electrical Specifications…………………………………………………....22

3.4 Installation of the 9036 Controller Board………………………………....23

3.5 Introduction to Touch Screen Controller Board……………………….…24

3.6 Windows 2000/XP/2003/Vista Universal Driver Installation for PenMount
6000 Series……………………………………………………………….…24

3.6.1 Installing Software………………………………………………………..24

3.6.2 Software Functions…………………………………………………….…28

Appendix A: Board Descriptions & Specifications

Descriptions……………………………………………………………………...39

Specifications…………………………………………………………………....39

Board Dimensions………………………………………………………………40

Appendix B: Panel Mounting and VESA Mounting 41

ARCDIS-1XX User Manual

4

Figures

Figure 1.1: Dimensions of ARCDIS-107….…...……….…………………..…..7
Figure 1.2: Dimensions of ARCDIS-110………………………………………..8
Figure 1.3: Dimensions of ARCDIS-112……………………………………..…9
Figure 1.4: Dimensions of ARCDIS-115………………………………………10

Figure 1.5: Front View of ARCDIS-107(P)…………………………………....11

Figure 1.6: Rear View of ARCDIS-107(P)…………………………………….11
Figure 1.7: Front View of ARCDIS-110(P)………..…………………………..12
Figure 1.8: Rear View of ARCDIS-110(P)………..………………………...…12
Figrue 1.9: Front View of ARCDIS-112(P)……..…………………………..…13
Figure 1.10: Rear View of ARCDIS-112(P)…………………………………...13
Figure 1.11: Front View of ARCDIS-115(P)……………………………….….14
Figure 1.12: Rear View of ARCDIS-115(P)…………………………………...14
Figure A: Dimensions of TB-6027(P)………………………………………….40

Figure B: Panel Mounting and VESA Mounting………………………….......41

ARCDIS-1XX User Manual

5

Chapter 1 Getting Started

ARCDIS-

107(P)

ARCDIS-

110(P)

ARCDIS-

112(P)

ARCDIS-

115(P)

Hardware

Display Type

7” 800x480

TFT LCD

10.1” 1280x800
TFT LCD

12.1” 800x600
TFT LCD

15” 1024x768

TFT LCD

External I/O

Port

Default I/O:

1 x VGA

1 x USB for Touch control

1 x 3 pins terminal block power input 9~36V DC

1 x DVI

1 x Tack switch for VGA / DVI transform

Option I/O:

1 x Line in by phone jack(option)

1 x DB-9 for Resistive Touch control

On Screen

Display Control

On board controller, extendable key pad from connector

Transfer Board OSD Membrane Keypad

LCD

Max.

Resolution

800x480

1280x800

800x600

1024x768

Max. Color

262 K

262K

16.2 M

16.2 M

Luminance

(cd/m²)

350

350

330

350

Contrast

Ratio

400:1

800:1

300:1

800:1

1.1 Features

Solid Aluminum Die-casting chassis
Variety of LCD panel size selections
Front bezel IP65
VGA/DVI input
9~36V DC wide range power input

1.2 Specifications

ARCDIS-1XX User Manual

6

Viewing

Angle (H/V)

140°/110°

160°/160°

160°/140°

160°/145°

Backlight

Lifetime

40,000 hrs

50,000 hrs

Power Input

9~36V DC on board

Touch Screen (ARCDIS-1XX)

Type

Resistive Touch Window

Interface

USB / RS-232 auto detect, when both connected USB is primary

Light

Transmission

Over 80%

Touch Screen (ARCDIS-1XXP)

Type

Projected Capacitive

Interface

USB interface on tail

Light

Transmission

Over 90%

Mechanical

Construction

Aluminum Die-casting chassis

Dimensions

(WxHxD)

202x149x39 mm

285x189x49 mm

319x245x52 mm

410x310x55 mm

Net Weight

1.0 kg

1.9 kg

2.6 kg

4.3 kg

Mounting

Panel / VESA 75x75

Panel / VESA 100x100

Environment Specifications

Operating

Temperature

0 ~ 50 ℃ (32 ~ 122 ℉)

Storage

Temperature

-20 ~ 60 ℃ (-4 ~ 140 ℉)

Storage

Humidity

10 ~ 90% @40℃ Non-condensing

IP Rating

Front Panel IP65

Certificate

CE/FCC Class A

* If you choose different touch interface (such as USB change to RS-232), it is necessary to reset the

power of ARCDIS.(plug on/off power supply)

ARCDIS-1XX User Manual

7

1.3 Dimensions

ARCDIS-1XX User Manual

Figure 1.1: Dimensions of ARCDIS-107

8

ARCDIS-1XX User Manual

Figure 1.2: Dimensions of ARCDIS-110

9

ARCDIS-1XX User Manual

Figure 1.3: Dimensions of ARCDIS-112

10

ARCDIS-1XX User Manual

Figure 1.4: Dimensions of ARCDIS-115

11

1.4 Brief Description of ARCDIS-1XX

ARCDIS-1XX is a total IP65 aluminum front bezel and chassis LCD Display, which comes with a 7
inch (luminance of 350 cd/m²) / 10.1 inch (luminance of 350 cd/m²) / 12.1 inch (luminance of 330 cd/m²)
/ 15 inch (luminance of 350 cd/m²) TFT LCD. ARCDIS-107(P) comes with a viewing angle of 140 (H)
degress and 110 (V) degress. ARCDIS-110(P) comes with a viewing angle of 160 (H) degrees and
160 (V) degress. ARCDIS-112(P) comes with a viewing angle of 160 (H) degrees and 140 (V) degrees.
ARCDIS-115(P) comes with a viewing angle of 160 (H) degrees and 145 (V) degrees. ARCDIS-1XX
has more outstanding features, thus giving the best in monitoring and control applications.
ARCDIS-107 can be VESA-75 mounted. ARCDIS-110, ARCDIS-112 and ARCDIS-115 can be
VESA-100 mounted.

Figure 1.5: Front View of ARCDIS-107(P)

Figure 1.6: Rear View of ARCDIS-107(P)

ARCDIS-1XX User Manual

12

Figure 1.7: Front View of ARCDIS-110(P)

Figure 1.8: Rear View of ARCDIS-110(P)

ARCDIS-1XX User Manual

13

Figure 1.9: Front View of ARCDIS-112(P)

ARCDIS-1XX User Manual

Figure 1.10: Rear View of ARCDIS-112(P)

14

Figure 1.11: Front View of ARCDIS-115(P)

ARCDIS-1XX User Manual

Figure 1.12: Rear View of ARCDIS-115(P)

15

1.5 Display Mode

Item

Resolution

H Freq.(kHz)

V Freq.(Hz)

Remark

1

640x350@70

31.469

70.087

VGA

2

640x400@70

31.469

70.087

VGA

3*

640x480@60

31.469

59.940

VESA

4

640x480@66

35.000

66.667

MAC

5

640x480@72

37.861

72.809

VESA

6*

640x480@75

37.500

75.000

VESA

7

720x400@70

31.469

75.000

TEXT

8

800x600@56

35.156

56.250

VESA

9*

800x600@60

37.879

60.317

VESA

10

800x600@72

48.077

72.188

VESA

11*

800x600@75

46.875

75.000

VESA

12

832x624@75

49.107

75.087

MAC

13

848x480@60

31.020

60.000

VESA

14*

1024x768@60

48.363

60.004

VESA

15*

1024x768@75

60.023

75.029

VESA

17

1152x864@70

63.850

70.000

VESA

18

1152x864@75

67.500

75.000

VESA

19

1152x900@76

71.809

76.149

SUN

20*

1280x768@60

47.730

60.000

VESA

21*

1280x768@75

60.290

74.890

VESA

ARCDIS-1XX User Manual

16

Chapter 2_________________________OSD

Cable Not Connected

2.1 AD Board OSD Functions

Auto Adjust Up/Left Down/Right Power

Menu/Entry Power Indicator

Power switch: To turn ON or OFF the power

Shift the icon to the right side or shift it up

Shift the icon to the left side or shift it down

Menu: To enter OSD menu for related icon and item.

Auto Button: One-touch auto adjustment

1.) Getting into Burn-in Mode

Before setting into a burn-in mode, first disconnect the AC power cord. Then press (don’t let them go)
the buttons until the AC power cord is connected and the “RGB” appears on the top left corner

of your screen. Now it can be put into the burn-in mode for changing colors.

2.) Getting Out of Burn-in Mode

Before getting out of the burn-in mode, please first disconnect the AC power cord. Then press the
button (If not workable, press the button and don’t let them go) until the AC power cord is
connected. Please don’t let your fingers go until the AC power cord is connected again and the
wording of “RGB” appears on the top left corner of your screen, and wait for 3 second. Under the
non-signal entry situation, if is seen, exit is thus successfully made.

When the Burn-in Mode is Unable to Eradicate…

ARCDIS-1XX User Manual

17

1.) If the “RGB” is still on the top left corner of the screen, press to enter “Miscellaneous” and

choose “Reset”, and then Yes, and press . When the screen goes black, disconnect power and
repeat the above steps.

2.) If the “RGB” is not found, disconnect the AC power cord first. Then press the buttons
(don’t let them go) until the AC power cord is connected, and wait for 2 to 3 seconds. When “RGB”

appears, repeat the above steps.

3.) Functions of OSD Keys

2.2 OSD Controls

To make any adjustment, select the following:

1. Press (Menu) to show the OSD menu or disable the OSD menu.

2. Select the icon that you wish to adjust with the ( / or +/-) key in the menu.

3. Press (Menu) and then choose the item with the ( / or +/-) key.

4. Press (Menu) and then adjust the quality with the ( / or +/-) key.

4.) If the “RGB” is still on the top left corner of the screen, press to enter “Miscellaneous” and

choose “Reset”, and then Yes, and press . When the screen goes black, disconnect power
and repeat the above steps.

5.) If the “RGB” is not found, disconnect the AC power cord first. Then press the buttons
(don’t let them go) until the AC power cord is connected, and wait for 2 to 3 seconds. When “RGB”

appears, repeat the above steps.

6.) Functions of OSD Keys

ARCDIS-1XX User Manual

18

2.3 OSD Function

ARCDIS-1XX

1. Luminance

1.1 Brightness

70 (50 for ARCDIS-110)

1.2 Contrast

50

1.3 Sharpness

3

2. Management

2.1 H. Position

auto

2.2 V. Position

auto

2.3 Pixel Clock

auto

2.4 Phase

auto

3. Color

6500

3.1 Red

80

3.2 Green

80

3.3 Blue

80

4.

5. Volume

4.1 Volume

50

4.2 Mute

on

5. OSD

5.1 H. Position

auto

5.2 V. Position

auto

5.3 OSD time

auto

6. Language

6.1 English

1. Power button: Power on/off

2. Down button: Brightness

3. Up button: Volume

4. Menu button: Menu

5. Auto button: Auto adjustment

2.4 OSD Default Parameter

ARCDIS-1XX User Manual

19

2.5 Main Menu

In the Main menu, there are the following items:

 Auto Adjust
 Luminance
 Management
 Color
 Volume
 OSD
 Language
 Recall
 Information
 Exit

For Luminance list, there are the following:

 Brightness
 Contrast
 Sharpness
 Exit

For Management list, there are the following:

 H. Position
 V. Position
 Pixel Clock
 Phase
 Exit

ARCDIS-1XX User Manual

20

For Color list, there are the following:

 9300
 6500
 5400
 User Preset
 Exit

In User Preset, there are the following:

 Red
 Green
 Blue
 Exit

For Volume list, there are the following:

 Volume
 Mute
 Exit

For OSD list, there are the following:

 H. Position
 V. Position
 OSD Time
 Exit

ARCDIS-1XX User Manual

21

For Recall list, there are the following:

 Recall Color
 Recall All
 Exit

For Language list, there are the following:

 English
 Francais
 Deutsch
 Italiano
 Espanol
 日本語
 繁體中文
 简体中文
 Portuguese
 한국의
 Pусский

For Information list, there are the following:

 Display Information
 Exit

ARCDIS-1XX User Manual

22

Chapter 3 Installation

3.1 Introduction to the PenMount 9036 Controller Board

The PenMount 9036 control board is configured for use with the RS-232 interface. It connects to the
touch screen, power supply and computer system’s RS-232 port, and supports 4-, 5- and 8-wire touch
screens. The control board has some advanced functions, such as PnP and non-PnP mode adjustable
baud rate, thus making easy for customers to select different touch screens without changing the
control board. The size of the board is 25 by 60mm, and it has two connectors and one dipswitch
on-board.

3.2 Features

 RS-232 interface
 Touch controller is DMC9000
 Design for the best touch performance and easy configuration
 PnP or Non-PnP mode selectable
 Design for best cost arrangement
 Supporting 2048x2048 pen device resolution
 19200 or 9600 baud rate transmission selectable
 Upgraded noise handling mechanism (3 level scheme)
 Fixed and high-speed sampling rate
 4-, 5- and 8-wire touch screen supported
 Touch screen cable, RS-232 with power cable connectors onboard
 5V to 12V power input
 Circuit protection for input voltage
 Touch-activated LED indicator onboard

3.3 Electrical Specifications

Touch Screen:
4-, 5- and 8-wire analog resistive type

Touch Screen Controller:
DMC9000

Communications:
RS-232
Baud Rate:
19200 and 9600 baud rate selection

ARCDIS-1XX User Manual

23

Resolution:

Switch

Definition

ON

OFF

S1

Baud Rate Adjustment

9600

19200

S2

PnP enable or disable

Disable

Enable

S3

Touch screen type

5-wire

4-, 8-wire

S4

Touch screen type

4-, 8-wire

5-wire

1024x1024 (10-bit A/D converter inside)

Power Input:
5V ~ 12V DC

Power Consumption:
12V: 24mA+ i where (i=v/touch screen sheet R)
5V: 20mA+ i where (i=v/touch screen sheet R)
Board Size:

6.0 x 2.5cm

Portrait:
Support 90∘to 279∘screen rotation

Static Protection:
ESD device (optional)

3.4 Installation of the 9036 Controller Board

Follow the steps below to install the 9036 control board:

1. Power down your computer and display, and open your display or system case. Find space on

your system and attach the control board to your system with screws. The control board has
industry standard 3φ screw holes.

2. Find the white 6-pin right-angle connector (on the left in the image above [see Figure 3.1]). The

power cable is pin 1 and pin 2. Solder the power and ground wire to the system. The RS-232 cable
is for pins 3 to 6. Attach the RS-232 cable’s D-sub connector to a COM port at the back of the
computer.

3. Find the white 9-pin right-angle connector (on the right in the image above [see Figure 3.1]). Attach

the female end of the touch screen cable to this connector. If you attach the cable of a 4-/5-/8-wire
touch screen to pins 1~5/1~6/1~9, attach the male end of the cable to the touch screen tail.

4. Mount your touch screen to the display.

5. Find the onboard DIP switch (on the upper right of the image above [see Figure 3.1]). This switch

selects baud rate, PnP or non-PnP mode, and touch screen type. Set the DIP switch to configure
your control board according to the definitions and settings of the table below:

ARCDIS-1XX User Manual

24

6. Turn on power to the computer and the display.

7. Install the software drivers and utilities and calibrate the touch screen.

This chapter describes how to install drivers and other software that will allow your PenMount 6000
Controller Board to work with different operating systems.

NOTE: PenMount USB drivers support up to 15 USB controllers.

3.5 Introduction to Touch Screen Controller Board

PenMount 6300 USB control board is a touch screen control board designed for USB interface and
specific for 4, 5, 8-wire touch screens. It is designed with USB interface features with multiple devices
supporting function. PenMount 6300 control board using PenMount 6000 controller that has been
designed for those who may like and all-in-one solution with 10-bit A/D converter built-in to make the
total printed circuit board denser, circuit diagram also designed for 12-bit ADC for optional. There are
two connectors on this board, one connector is for 4, 5, 8-wire touch screen cable (optional), and
another is for 4-pin USB A type cable (optional).

3.6 Windows 2000/XP/2003/Vista Universal Driver Installation

for PenMount 6000 Series

Before installing the Windows 2000/XP driver software, you must have the Windows 2000/XP system
installed and running on your computer. You must also have one of the following PenMount 6000
series controller or control boards installed: PM6500, PM6300.

3.6.1 Installing Software

If you have an older version of the PenMount Windows 2000/XP driver installed in your system, please
remove it first. Follow the steps below to install the PenMount DMC6000 Windows 2000/XP driver.

ARCDIS-1XX User Manual

25

Step 1. Please make sure your PenMount 6000 device had plugged in advance. If your device uses
RS232 interface, please plugged in before the machine is turned on. When the system first detects the
controller board, a screen appears that shows “Unknown Device”. Do not use this hardware wizard.
Press Cancel.

Step 2. Insert the product CD install setup.exe. Click touch panel driver

ARCDIS-1XX User Manual

26

Step 3. A License Agreement appears. Click “I Agree…” and “Next”

Step 4. Choose the folder in which to install PenMount Windows Universal Driver. Click Install.

ARCDIS-1XX User Manual

27

Step 5. Wait for installation. Click Next to continue.

Step 6. Click OK.

ARCDIS-1XX User Manual

28

Step 7. Click Finish to complete installation.

3.6.2 Software Functions

Upon rebooting, the computer automatically finds the new 6000 controller board. The touch screen is
connected but not calibrated. Follow the procedures below to carry out calibration.

1. After installation, click the PenMount Monitor icon “PM” in the menu bar.

2. When the PenMount Control Panel appears, select a device to “Calibrate.”

PenMount Control Panel

The functions of the PenMount Control Panel are Device, Multiple Monitors, Tools and About,
which are explained in the following sections.

Device

In this window, you can find out that how many devices are detected on your system.

ARCDIS-1XX User Manual

29

Standard Calibration

Click this button and arrows appear pointing to red
squares. Use your finger or stylus to touch the red
squares in sequence. After the fifth red point

calibration is complete. To skip, press ‘ESC’.

Advanced Calibration

Advanced Calibration uses 4, 9, 16 or 25 points to
effectively calibrate touch panel linearity of aged
touch screens. Click this button and touch the red
squares in sequence with a stylus. To skip, press

ESC’.

Command Calibration

Command call calibration function. Use command
mode call calibration function, this can uses
Standard, 4, 9, 16 or 25 points to calibrate E.g.

Please run ms-dos prompt or command prompt
c:\Program Files\PenMount Universa
Driver\Dmcctrl.exe -calibration 0 ( Standard
Calibration) Dmcctrl.exe - calibration ($) 0= Standard
Calibration 4=Advanced Calibration 4 9=Advanced
Calibration 9 16=Advanced Calibration 16
25=Advanced Calibration 25

Calibrate

This function offers two ways to calibrate your touch screen. ‘Standard Calibration’ adjusts most touch

screens. ‘Advanced Calibration’ adjusts aging touch screens.

ARCDIS-1XX User Manual

30

Step 1. Please select a device then click “Configure”. You can also double click the device too.

Step 2.Click “Standard Calibration” to start calibration procedure

ARCDIS-1XX User Manual

31

NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an
accurate calibration. Use a stylus during Advanced Calibration for greater accuracy. Please follow the
step as below:

Step 3.Come back to “PenMount Control Panel” and select “Tools” then Click “Advanced
Calibration”.

Select “Device” to calibrate, then you can start to do “Advanced Calibration”.

ARCDIS-1XX User Manual

32

Plot Calibration Data

Check this function and a touch panel linearity
comparison graph appears when you have finished
Advanced Calibration. The blue lines show linearity
before calibration and black lines show linearity
after calibration.

Turn off EEPROM storage

The function disable for calibration data to write in
Controller. The default setting is Enable.

NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy.

ARCDIS-1XX User Manual

33

Setting

Touch Mode

This mode enables and disalbes the mouse’s ability to drag
on-screen icons – useful for congifuring POS terminals.
Mouse Emulation – Select this mode and the mouse functions
as normal and allows dragging of icons.
Click on Touch – Select this mode and the mouse only
provides a click function, and dragging is disabled

Beep Sound

Enabled Beep Sound – turns beep function on and off
Beep on Pen Down – beep occurs when pen comes down
Beep on Pen Up – beep occurs when pen comes down
Beep on both – beep occurs when comes down and lifted up
Beep Frequency – modifies sound frequency
Beep Duration – modifies sound duration

Cursor Stabilizer

Enable the function support to prevent cursor shake

Use press and hold
as right click

You can set the time out and area for you need.

ARCDIS-1XX User Manual

34

About

This panel displays information about the PenMount controller and driver version.

Multiple Monitors

Multiple Monitors supports from two to six touch screen displays for one system. The PenMount
drivers for Windows 2000/XP support Multiple Monitors. This function supports from two to six touch
screen displays for one system. Each monitor requires its own PenMount touch screen control board,
either installed inside the display or in a central unit. The PenMount control boards must be connected
to the computer COM ports via the RS-232 interface. Driver installation procedures are the same as
for a single monitor. Multiple Monitors supports the following modes:

Windows Extend Monitor Function
Matrox DualHead Multi-Screen Function
nVidia nView Function

NOTE: The Multiple Monitors function is for use with multiple displays only. Do not use this function if
you have only one touch screen display. Please note once you turn on this function the Rotating
function is disabled.

Enable the multiple display function as follows:
Step 1. Check the Multiple Monitor Support box; then click Map Touch Screens to assign touch

controllers to displays.

ARCDIS-1XX User Manual

35

Step 2. When the mapping screen message appears, click “OK”

Step 3. Touch each screen as it displays Please touch this monitor. Press ‘S’ to skip Following this
sequence and touching each screen is called mapping the touch screens.

ARCDIS-1XX User Manual

36

Draw

Tests or demonstrates the PenMount touch
screen operation.

Advanced Calibration

Enable Advanced Calibration function

Right Button Icon

Enable right button function. The icon can
show on Desktop or System Tray (menu bar).

Step 4. After the setting procedure is finished, maybe you need to calibrate for each panel and

controller

NOTES:

1. If you used a single VGA output for multiple monitors, please do not use the Multiple Monitors

function. Just follow the regular procedure for calibration on each of your desktop monitors.

2. The Rotating function is disabled if you use the Multiple Monitors function.

3. If you change the resolution of display or screen address, you have to redo Map Touch Screens so

the system understands where the displays are.

4. If you more monitor mapping one touch screen, Please press ‘S’ to skip mapping step.

Tools

ARCDIS-1XX User Manual

37

About

You can see how many devices of PenMount controller that are plugged to your system

PenMount Monitor Menu Icon

The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/XP system when you
turn on PenMount Monitor in PenMount Utilities.

ARCDIS-1XX User Manual

38

PenMount Monitor has the following function

Control Panel

Open Control Panel Windows

Beep

Setting Beep function for each device

Right Button

When you select this function, a mouse icon appears in
the right-bottom of the screen.
Click this icon to switch between Right and Left Button
functions.

Exit

Exits the PenMount Monitor function.

PenMount Rotating Functions

The PenMount driver for Windows 2000/XP supports several display rotating software packages.
Windows Me/2000/XP support display rotating software packages such as:

• Portrait’s Pivot Screen Rotation Software

• ATI Display Driver Rotate Function

• nVidia Display Driver Rotate Function

• SMI Display Driver Rotate Function

• Intel 845G/GE Display Driver Rotate Function

Configuring the Rotate Function

1. Install the rotation software package.

2. Choose the rotate function (0°, 90°, 180°, 270°) in the 3rd party software. The calibration screen

appears automatically. Touch this point and rotation is mapped.

NOTE: The Rotate function is disabled if you use Monitor Mapping

ARCDIS-1XX User Manual

39

Appendix A: Board Descriptions & Specifications

Model

Function Descriptions

TB-6027

AD board,VGA /DVI input,LVDS output,Audio

TB-6027T

AD board,VGA/DVI input,LVDS output,Audio,Touch
controller

Specifications

Board Size

113mm x 170mm

Chipset

Mstar TSUMU58NWHJ-LF PQFP128

Input

1 x VGA input Port,DB15 connector

1 x DVI-D input（option）

1 x RS232 input port, DB9 connector (option)
1 x USB 2.0 input port, Single USB connector
1 x Line in port,JACK (option)
1 x 3-pin power input connector (Wide range DC+9V~32V)
1 x SW1 (Select VGA or DVI signal input)
1 x OSD function support
1 x Touch controller

Output

1 x LVDS output

1 x Audio Power Amplifier (Line out)

Resolution

Up to 1920 x1080 for LVDS

Power input

DC9V-36V

Temperature

Operating: -20℃ to 70℃
Storage: -40℃ to 85℃

Humidity

10% - 90%, non-condensing, operating

EMI/EMS

Meet CE/FCC class A

Descriptions

Specifications

ARCDIS-1XX User Manual

40

Board Dimensions

(units :mm)

Figure A: Dimensions of TB-6027(P)

ARCDIS-1XX User Manual

41

Appendix B: Panel Mounting and VESA Mounting

*Notice：

Tighten the mounting clip screws by hand until the gasket seal contacts the

mounting surface uniformly.

Tighten the mounting clips screws to a torque of 8 ~ 10 kgf-cm by using the

specified sequence, making sure not to overtighten.

*Tighten the mounting clips to the specified torque to provide a proper seal and to
prevent damage to the product. Aplex assumes no responsibility for water or
chemical damage to the product or other equipment within the enclosure due to
improper installation.

The ARCDIS-1XX is designed to be panel-mounted and VESA mounted as shown in Picture. Just
carefully place the unit through the hole and tighten the given 10 screws from the rear to secure the
mounting.

Figure B: Panel mounting and VESA mounting

ARCDIS-1XX User Manual