1
APC-3x93P_3X93R
(SBC-7106A – 17” and 19”)
User Manual
Release Date _ Revision
Oct. 2014 V1.0
® 2014 Aplex Technology, Inc. All Rights Reserved. Published in Taiwan
Aplex Technology, Inc.
15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan
Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: aplex@aplex.com.tw URL: www.aplex.com.tw
APC-3x93P_R (SBC-7106A) User Manual
2
Warning!___________________________________
This equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions manual, it may cause interference to radio
communications.
It has been tested and found to comply with the limits for a Class A computing device pursuant
to FCC Rules, which are designed to provide reasonable protection against such interference when
operated in a commercial environment. Operation of this equipment in a residential area is likely to
cause interference in which case the user at his own expense will be required to take whatever
measures may be required to correct the interference.
Electric Shock Hazard – Do not operate the machine with its back cover removed. There are
dangerous high voltages inside.
APC-3x93P_R (SBC-7106A) User Manual
3
Packing List
Accessories (as ticked) included in this package are:
□ Adaptor
□ Driver & manual CD disc
□ Other.___________________(please specify)
Safety Precautions
Follow the messages below to prevent your systems from damage:
◆ Avoid your system from static electricity on all occasions.
◆ Prevent electric shock. Don‘t touch any components of this card when the card is
power-on. Always disconnect power when the system is not in use.
◆ Disconnect power when you change any hardware devices. For instance, when you
connect a jumper or install any cards, a surge of power may damage the electronic
components or the whole system.
APC-3x93P_R (SBC-7106A) User Manual
4
Table of Contents______________________
Warning!…………………………………………………………………………….……..….2
Packing List…………………………………………………………………………………..3
Safety Precautions…………………………………………………………………………..3
Chapter 1 Getting Started
1.1 Features…….……………………………………..….……………………..6
1.2 Specifications……………………………...……………………………......6
1.3 Dimensions……………………………………………………….……....…8
1.4 Brief Description of APC-3x93P/APC-3x93R………………………….…9
Chapter 2 Hardware
2.1 Mainboard Introduction………….…………………………………..…....10
2.2 Specifications………………………………………………………………10
2.3 Jumpers and Connectors Location………………………………………13
2.4 Jumpers Setting and Connectors………………………………………..14
Chapter 3 BIOS Setup
3.1 Operations after POST Screen.............................................................39
3.2 BIOS Setup Utility……..........................................................................39
3.3 Main Settings…....................................................................................40
3.4 Advanced Settings................................................................................41
3.5 Chipset Settings...................................................................................47
3.6 Boot Settings........................................................................................50
3.7 Security Settings...................................................................................52
3.8 Save and Exist Settings........................................................................53
Chapter 4 Installation of Drivers
4.1 Intel Chipset Driver.…………………………...………………………..…60
4.2 Intel Graphics Media Accelerator Driver...……………………………....63
4.3 Intel (R) Network Adapter……..………………………………………….66
4.4 Realtek ALC662 HD Audio Driver Installation…….………….…………69
APC-3x93P_R (SBC-7106A) User Manual
5
Chapter 5 Touch Screen Installation
5.1 Windows 2000/2003/Vista/WIN7 Universal Driver Installation for
PenMount 6000 Series…………………………………………………....67
5.2 Software Functions...............................................................................77
Figures
Figure 1.1: Dimensions of APC-3793P(R)……..………...……………..…......8
Figure 1.2: Dimecsions of APC-3993P(R).………………..…………………...8
Figure 1.3: Front view of APC-3X93P(R).…………………………………...…9
Figure 1.4: Rear view of APC-3X93P(R)..…………………………………...…9
Figure 2.1: Mainboard Dimensions…………………………………..…….....12
Figure 2.2: Jumpers and Connectors Location_ Board Top………………...13
Figure 2.3: Jumpers and Connectors Location_ Board Bottom…………....13
APC-3x93P_R (SBC-7106A) User Manual
6
Chapter 1 Getting Started
APC-3793P(R)
APC-3993P
System
CPU
Intel® Atom Processor D2550(1M Cache, 1.8GHz)
System Chipset
Intel NM10 Express
System Memory
Onboard 4GB DDR3
IO Port
USB
1 x M12 8 pin for USB 1/2
1 x M12 8 pin for USB 3/4
Serial/Parallel
1 x M12 8pin for COM 1/RS-232/422/485 (Default RS-232)
1 x M12 8pin for COM 2/RS-232
Audio
N/A
Membrane control
N/A
LAN
1 x M12 8pin for LAN
Power
1 x M12 3 pin DC power connector
Storage Space
HDD
1 x 2.5” SATA HDD or SSD
Movable device
1 x Internal SD Card slot on board
Expansion
On board expansion
bus
1 x Mini PCIe half size slot
Display
Display Type
17” TFT-LCD
19” TFT-LCD
Max. Resolution
1280x1024
1280 x 1024
1.1 Features
Fanless and Low Power Consumption Stainless Steel Panel PC
Intel® Atom™ Processor D2550 (1M Cache, 1.8GHz)
Onboard 4G DDR3
11~32V DC wide-ranging power input
M12 I/O Connector
Full Flat bezel Design, Total 6 sides IP 65/ IP69K
Projective capacitive touch/ Resistive Type
1.2 Specifications
APC-3x93P_R (SBC-7106A) User Manual
7
Max. Color
16.7M
16.7M
Contrast Ratio
1000 : 1
1000 : 1
Luminance (cd/m²)
350
350
View angle(H°/V°)
170/170
170/165
Touch Screen (for APC-3X93P)
Type
Projective Capacitive
Interface
USB
Light
Transmission(%)
90%
Touch Screen (for APC-3X93R)
Type
Resistive touch window
Interface
USB
Light
Transmission(%)
80%
Power
Power Input
11~32V DC
Power Consumption
Max:21.36W
Max:32W
Mechanical
Construction
Stainless steel
IP Rating
Total IP65 6 sides / IP69 K
Mounting
VESA 75 x 75
VESA 100 x 100
Dimension (mm)
432 x 358 x 56
470 x 388.6 x 60
Net Weight (Kgs)
7.2KG
9.4KG
Environmental
Operating
temperature(°C)
0℃ to 50℃ (with HDD)
-20~60 (with Industrial SSD or CF)
Storage
temperature(°C)
-30~70℃
Storage humidity
10 to 90% @ 40°C, non- condensing
Certification
CE / FCC Class A
Operating System
Support
WES7 32bit, W7PES
APC-3x93P_R (SBC-7106A) User Manual
8
1.3 Dimensions
Figure 1.1: Dimensions of APC-3793P(R)
APC-3x93P_R (SBC-7106A) User Manual
Figure 1.2: Dimensions of APC-3993P
9
1.4 Brief Description of APC-3x93P/3x93R
APC-3x93P/3X93R series comes with IP65 certificated and is powered by Intel Atom D2550 to
provide low power consumption. The stainless steel chassis design makes it exceptionally suitable for
strict hygiene regulations for food/chemical industry, medical, restaurant/kitchen applications, storage
management and outdoor /information segment and so on. APC-3x93P/3X93R series has touch
screen of projective capacitive type and resistive type window for option. The APC-3x93P/3X93R
series has advanced computing performance and lower power consumption thanks to well-equipped
Intel Atom D2550 solution with 4G DDR3 on board. Regarding the storage capability,
APC-3x93P/3X93R series provides 1 x 2.5” SATA HDD, 1 x internal SD Slot and 1x internal mini-PCIe
allowing customers to easily access/backup the data. APC-3x93P/3X93R series supports OS such as
Windows Embedded Standard 7, Windows 7 Pro for Embedded and so on.
Figure 1.3: Front View of APC-3x93P(R)
APC-3x93P_R (SBC-7106A) User Manual
Figure 1.4: Rear View of APC-3x93P(R)
10
Chapter 2 Hardware
Specifications
Board Size
170mm x 113mm
CPU Support
Intel Atom D2550 /1.86GHz (2cores,10W, onboard)
Intel Atom N2600 /1.60GHz (2cores,3.5W, option）
Chipset
Intel NM10 Express
Memory Support
Onboard 4GB DDRIII SDRAM (D2550)
Onboard 2GB DDRIII SDRAM (N2600,option)
Graphics
Integrated Intel GMA 3650 (D2550)
Integrated Intel GMA 3600 (N2600)
Display Mode
1 x CRT Port
1 x HDMI Port
1 x LVDS (18/24-bit dual LVDS)
Support
Resolution
Up to 1920 x 1200 for CRT
Up to 1920 x 1200 for HDMI
Up to 1920 x 1200 for LVDS (PS8625)
Dual Display
CRT+LVDS
CRT+HDMI
LVDS+HDMI
Super I/O
Winbond W83627UHG-E
BIOS
AMIBIOS
Storage
1 x SATA Connector (7P)
1 x SATA Connector (7P+15P)
1 x SD Socket (USB to SD)
Ethernet
2 x PCIe Gbe LAN by Intel 82574L
2.1 Mainboard Introduction
SBC-7106A is a 4" industrial motherboard developed on the basis of Intel Cedarview-M/D Processors
and NM10, which provides abundant peripheral interfaces to meet the needs of different customers.
Also, it features dual GbE ports, 3-COM ports and one Mini PCIE configuration,one VGA port, one
HDMI port, one LVDS interface. To satisfy the special needs of high-end customers, CN1 and CN2
and CN3 richer extension functions. The product is widely used in various sectors of industrial control.
2.2 Specifications
APC-3x93P_R (SBC-7106A) User Manual
11
USB
2 x USB 2.0 (type A)stack ports (USB4/USB5)
2 x USB 2.0 Pin header for CN3 (USB2/USB3)
1 x USB 2.0 Pin header for CN1 (USB0,option)
1 x USB 2.0 Pin header for CN2 (USB1)
1 x USB 2.0 for MPCIE1 (USB7)
Serial
1 x RS232/RS422/RS485 port, DB9 connector for external
COM1)
pin 9 w/5V/12V/Ring select
1 x RS232 port, DB9 connector for external (COM2)
pin 9 w/5V/12V/Ring select
1 x RS422/485 header for CN2 (COM3)
2 x UART for CN3 (COM5,COM6)
Digital I/O
8-bit digital I/O by Pin header (CN2)
4-bit digital Input
4-bit digital Output
4-bit digital I/O by Pin header (CN3)
2-bit digital Input
2-bit digital Output
Battery
Support CR2477 Li battery by 2-pin header
Audio
Support Audio via Realtek ALC662 HD audio codec
Support Line-in, Line-out, MIC by 2x6-pin header
Keyboard /Mouse
1 x PS2 keyboard/mouse by 1x6 box pin header (CN3)
Expansion Bus
1 x mini-PCI-express slot
1 x PCI-express (CN3)
Touch Ctrl
1 x Touch ctrl header for TCH1 (COM4)
Power
Management
Wide Range DC9V~36V input
1 x 3-pin power input connector
Switches and
LED Indicators
1 x Power on/off switch (BT1/BT2/CN2/CN3)
1 x Reset (CN2)
1 x Power LED status (CN1)
1 x HDD LED status (CN2)
1 x Buzzer
External I/O port
2 x COM Ports (COM1/COM2)
2 x USB 2.0 Ports (stack)
2 x RJ45 GbE LAN Ports
1 x HDMI Port
1 x Stack audio Jack (Line out)
APC-3x93P_R (SBC-7106A) User Manual
12
Watchdog Timer
Software programmable 1 – 255 second by Super I/O
Temperature
Operating: -20℃ to 70℃
Storage: -40℃ to 85℃
Humidity
5% - 95%, non-condensing, operating
Power
Consumption
12V /0.95A (Intel Atom N2600 processor with 2GB DDR3
DRAM)
EMI/EMS
Meet CE/FCC class A
TB-528CAN2
2 x CAN bus
1 x SIM Card Socket
1 x mini-PCI-express slot
(units :mm)
Figure 2.1: Mainboard Dimensions
APC-3x93P_R (SBC-7106A) User Manual
13
2.3 Jumpers and Connectors Location
Figure 2.2: Jumpers and Connectors Location- Board Top
Figure 2.3: Jumpers and Connectors Location- Board Bottom
APC-3x93P_R (SBC-7106A) User Manual
14
2.4 Jumpers Setting and Connectors
Model
CPU
SBC-7106A-D25-4G
D2550
SBC-7106A-D25P-4G
D2550（option）
SBC-7106A-N26-2G
N2600（option）
Model
Memory
SBC-7106A-D25-4G
4GB
SBC-7106A-D25P-4G
4GB（option）
SBC-7106A-N26-2G
2GB（option）
JP5
Mode
Open
ATX Power
Close
Auto Power on (option)
S-422
Mode
Pin11-12（Off）
ATX Power
Pin11-12（On）
Auto Power on (Default)
JP3
CMOS
Open
Normal (Default)
Close 1-2
Clear CMOS
1. CPU1:
(FCBGA559), onboard Intel Intel Cedarview-M/D Processors
2. H3/H4/H5/H6:
CPU1 and U53 Heat Sink Screw holes, four screw holes for intel D2550 (or N2600)
and NM10 Heat Sink assemble.
3. U5/U6/U7/U8/U9/U10/U11/U12:
Onboard DDRIII Memory
4. JP5:
(2.0mm Pitch 1x2 box Pin Header), ATX Power and Auto Power on jumper setting.
5. JP3:
(2.0mm Pitch 1x2 Pin Header) CMOS clear jumper, CMOS clear operation will
permanently reset old BIOS settings to factory defaults.
APC-3x93P_R (SBC-7106A) User Manual
15
Procedures of CMOS clear:
Model
JP3
SBC-7106A-N26
No
SBC-7106A-D25
Yes
SBC-7106A-D25P
Yes
Pin#
Signal Name
Pin1
VBAT
PIN2
Ground
Pin#
Power Input
Pin1
DC+9V~32V
Pin2
Ground
Pin3
FG
Model
DC_IN1
SBC-7106A-D25
180°Connector
SBC-7106A-D25P
45°Connector
SBC-7106A-N26
180°Connector
a) Turn off the system and unplug the power cord from the power outlet.
b) To clear the CMOS settings, use the jumper cap to close pins 1 and 2 for about 3
seconds then reinstall the jumper clip back to pins open.
c) Power on the system again.
d) When entering the POST screen, press the <F1> or <DEL> key to enter CMOS Setup
Utility to load optimal defaults.
e) After the above operations, save changes and exit BIOS Setup.
6. BAT1:
(1.25mm Pitch 1x2 box Pin Header) 3.0V Li battery is embedded to provide power for
CMOS.
7. DC_IN1:
(5.08mm Pitch 1x3 Pin Connector),DC9V~32V System power input connector.
8. BT1/BT2:
Power on/off button, They are used to connect power switch button. The two pins are
disconnected under normal condition. You may short them temporarily to realize system
startup & shutdown or awaken the system from sleep state.
APC-3x93P_R (SBC-7106A) User Manual
16
9. CPU_FAN1:
Pin#
Signal Name
1
Ground
2
VCC
3
Rotation detection
Model
CPU_FAN1
SBC-7106A-D25
Yes
SBC-7106A-D25P
Yes
SBC-7106A-N26
No
Signal Name
Pin#
Pin#
Signal Name
CRT_RED
1
2
Ground
CRT_GREEN
3
4
Ground
CRT_BLUE
5
6
VGA_EN
CRT_H_SYNC
7
8
CRT_DDCDATA
CRT_V_SYNC
9
10
CRT_DDCCLK
Ground
11
12
Ground
VGA hot plug setting for Windows XP：
VGA1（Pin Header）
Function
Pin4-Pin6（Close）
VGA Simulation Disabled
Pin4-Pin6（Open）
VGA Simulation Enabled
use the 2.0mm jumper cap to close pin 4 and pin6
(2.54mm Pitch 1x3 Pin Header),Fan connector, cooling fans can be connected directly for
use. You may set the rotation condition of cooling fan in menu of BIOS CMOS Setup.
Note:
Output power of cooling fan must be limited under 5W.
10. VGA1:
(CRT 2.0mm Pitch 2X6 Pin Header), Video Graphic Array Port, Provide 2x6Pin cable to
VGA Port.
11. HDMI1:
(HDMI 19P Connector), High Definition Multimedia Interface connector.
APC-3x93P_R (SBC-7106A) User Manual
17
12. JP6:
JP6
Function (CN1)
Pin1-Pin2（Close）
Single channel LVDS
Pin1-Pin2（Open）
Dual channel LVDS (Default)
Pin3-Pin4（Close）
8/24 bit (Default)
Pin3-Pin4（Open）
6/18 bit
Model
LVDS resolution
SBC-7106A-D25
SBC-7106A-D25P
SBC-7106A-N26
1280*1024 (Default)
800*480（option）
800*600（option）
1024*768（option）
1920*1080（option）
……
Pin#
Signal Name
1
+DC12V
2
+DC12V
3
Ground
4
Ground
5
BKLT_EN_OUT
6
BKLT_CTRL
(2.0mm Pitch 2x2 Pin Header), LVDS jumper setting.
13. U66:
AT24C02-DIP8,The EEPROM IC（U66）is the set of LVDS resolution.
If you need other resolution settings, please update U66 data.
14. INVT1:
(2.0mm Pitch 1x6 wafer Pin Header), Backlight control connector for LVDS.
APC-3x93P_R (SBC-7106A) User Manual
18
Note:
Function
Signal Name
Pin#
Signal Name
Function
LVDS
12V_S0
2 1 12V_S0
LVDS
BKLT_EN_OUT
4 3 BKLT_CTRL
Ground
6 5 Ground
LVDS_VDD5
8 7 LVDS_VDD5
LVDS_VDD3
10 9 LVDS_VDD3
Ground
12
11
Ground
LA_D0_P
14
13
LA_D0_N
LA_D1_P
16
15
LA_D1_N
LA_D2_P
18
17
LA_D2_N
LA_D3_P
20
19
LA_D3_N
LA_CLKP
22
21
LA_CLKN
LB_D0_P
24
23
LB_D0_N
LB_D1_P
26
25
LB_D1_N
LB_D2_P
28
27
LB_D2_N
LB_D3_P
30
29
LB_D3_N
LB_CLKP
32
31
LB_CLKN
Ground
34
33
Ground
USB0
(JP4 open)
USB0
(JP4 open)
USB0_P
36
35
USB0_N
5V_S5_USB
38
37
5V_S5_USB
Power LED
PWR_LED+
40
39
Ground
Power LED
Function
S_232 Pin#
RS232
(Default)
ON:
Pin1, Pin2, Pin3, Pin4
Pin6 is backlight control signal, support DC or PWM mode, mode select at BIOS CMOS
menu.
15. CN1:
(1.25mm Pitch 2x20 Connector, DF13A-40DP-1.25V), For 18/24-bit LVDS2 output
connector, Fully supported by Parad PS8625(DP to LVDS), the interface features dual
channel 24-bit output. Low Voltage Differential Signaling, A high speed, low power data
transmission standard used for display connections to LCD panels.
17. S_232:
(Switch),COM1 jumper setting, it provides selectable RS232 or RS422 or RS485 serial
signal output.
APC-3x93P_R (SBC-7106A) User Manual
19
RS422
(option)
OFF:
Pin1, Pin2, Pin3, Pin4
RS485
(option)
OFF:
Pin1, Pin2, Pin3, Pin4
18. S_422:
Function
S_422 Pin#
RS232
(Default)
OFF:
Pin1, Pin2, Pin3, Pin4
RS422
(option)
ON:
Pin1, Pin2, Pin3, Pin4
RS485
(option)
ON:
Pin1, Pin2, Pin3, Pin4
S-422
Mode
Pin11-12（Off）
ATX Power
Pin11-12（On）
Auto Power on (Default)
RS232 (Default):
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
JP1 select Setting (RI/5V/12V)
BIOS Setup：
Advanced/W83627UHG Super IO
Configuration/Serial Port 1 Configuration【RS-232】
(Switch),COM1 setting, it provides selectable RS232 or RS422 or RS485 serial signal
output.
19. COM1:
(Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a direct
connection to serial devices. COM1 port is controlled by pins No.1~6 of JP1,select
output Signal RI or 5V or 12V, For details, please refer to description of JP1 and S_232
and S_422 setting.
APC-3x93P_R (SBC-7106A) User Manual
20
RS422 (option):
Pin#
Signal Name
1
422_RX+
2
422_RX-
3
422_TX-
4
422_TX+
5
Ground
6
NC
7
NC
8
NC
9
NC
BIOS Setup：
Advanced/W83627UHG Super IO
Configuration/Serial Port 1 Configuration【RS-422】
RS485 (option):
Pin#
Signal Name
1
NC
2
NC
3
485-
4
485+
5
Ground
6
NC
7
NC
8
NC
9
NC
BIOS Setup：
Advanced/W83627UHG Super IO
Configuration/Serial Port 1 Configuration【RS-485】
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
21. COM2:
(Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a direct
connection to serial devices.
APC-3x93P_R (SBC-7106A) User Manual
21
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
JP2 select Setting (RI/5V/12V)
JP4
Function
USB0 (CN1)
Touch(TCH1)
Close 3-4(default)
-
Yes
Open 3-4(option)
Yes
-
Open 1-2(default)
-
Pin#
Signal Name
1
SENSE
2
X+ 3 X- 4 Y+ 5 Y- 6 GND_EARCH
Pin#
Signal Name
1
+DC5V
2
Ground
22. JP4:
(2.0mm Pitch 2x2 wafer Pin Header),USB0(CN1) or Touch jumper setting.
23. TCH1:
(2.0mm Pitch 1x6 wafer Pin Header), internal Touch controller connector.
24. LED1, LED2, LED3 (option):
LED1: LED STATUS. Green LED for Motherboard Power status.
LED2: LED STATUS. Green LED for Motherboard Standby Power Good status.
LED3: LED STATUS. Green LED for Touch Power status.
25. SATA_P:
(2.5mm Pitch 1x2 box Pin Header), One onboard 5V output connector are reserved to
provide power for SATA devices.
APC-3x93P_R (SBC-7106A) User Manual
22
Note:
Signal Name
Pin#
Pin#
Signal Name
+5V 1 2
GND_AUD
LINE-OUT-L
3
4
LINE-OUT-R
FRONT_JD
5
6
LINE1_JD
LINE-IN-L
7
8
LINE-IN-R
MIC-IN-L
9
10
MIC-IN-R
GND_AUD
11
12
MIC1_JD
Output current of the connector must not be above 1A.
26. SATA2:
(SATA 7Pin), SATA Connectors, one SATA connector are provided, with transfer speed
up to 3.0Gb/s.
27. SATA1:
(SATA 7Pin+15Pin), SATA Connectors, one SATA connector are provided, with transfer
speed up to 3.0Gb/s.
28. SD1:
(SD card socket),Secure Digital Memory Card socket.
29. MPCIE1:
(Socket 52Pin),mini PCIe socket, it is located at the top, it supports mini PCIe devices
with USB2.0 and LPC and SMBUS and PCIe signal. MPCIe card size is 30x30mm.
30. H1/H2:
MPCIE1 SCREW HOLES, H1and H2 for mini PCIE card (30mmx30mm) assemble.
31. AUDIO:
(2.0mm Pitch 2X6 Pin Header), Front Audio, An onboard Realtek ALC662 codec is used
to provide high-quality audio I/O ports. Line Out can be connected to a headphone or
amplifier. Line In is used for the connection of external audio source via a Line in cable.
MIC is the port for microphone input audio.
32. LINE_OUT:
(Diameter 3.5mm Jack), HD Audio port, An onboard Realtek ALC662 codec is used to
provide high quality audio I/O ports. Line Out can be connected to a headphone or
amplifier.
APC-3x93P_R (SBC-7106A) User Manual
23
Function
Signal Name
Pin#
Signal Name
Function
5V
5V_S5
2 1 5V_S5
5V
SIO_GPIO61
GPIO_IN2
4 3 GPIO_IN1
SIO_GPIO60
SIO_GPIO63
GPIO_IN4
6 5 GPIO_IN3
SIO_GPIO62
SIO_GPIO21
GPIO_OUT2
8 7 GPIO_OUT1
SIO_GPIO20
SIO_GPIO23
GPIO_OUT4
10 9 GPIO_OUT3
SIO_GPIO22
Ground
12
11
Ground
33. USB45:
USB4/USB5：(Double stack USB type A), Rear USB connector, it provides up to 4
USB2.0 ports, High-speed USB 2.0 allows data transfers up to 480 Mb/s ,support USB
full-speed and low-speed signaling.
Each USB Type A Receptacle (2 Ports) Current limited value is 1.5A.
If the external USB device current exceeds 1.5A, please separate connectors into
different Receptacle.
34. LAN1/LAN2:
LAN1/LAN2: (RJ45 Connector), Rear LAN port, Two standard 10/100/1000M RJ-45
Ethernet ports are provided. Used intel 82574L chipset, LINK LED (green) and ACTIVE
LED (yellow) respectively located at the left-hand and right-hand side of the Ethernet
port indicate the activity and transmission state of LAN.
35. BUZ1:
Onboard buzzer.
36. CN2:
(DF13-30P Connector),For expand output connector, It provides eight GPIO,one RS422
or RS485,one USB2.0,one Power on/off, one Reset.
APC-3x93P_R (SBC-7106A) User Manual
24
485 or 422
485+_422TX+
14
13
485-_422TX-
485 or 422
RS422
422_RX+
16
15
422_RX-
RS422
NC
18
17
NC
NC
20
19
NC
5V
5V_S0
22
21
HDD_LED+
HDD LED
USB2.0
5V_USB01
24
23
5V_USB01
USB2.0
USB1_P
26
25
USB1_N
Ground
28
27
FP_RST-
RESET
Power auto on
PWRBTN_ON
30
29
Ground
COM3 BIOS Setup：
Advanced/W83627UHG Super IO Configuration/Serial Port 3 Configuration
【RS-422】
Advanced/W83627UHG Super IO Configuration/Serial Port 3 Configuration
【RS-485】
Function
Signal Name
Pin#
Signal Name
Function
5V_S5_USB
1 2 5V_S5_USB
5V_S5_USB
3 4 5V_S5_USB
USB23_OC
5 6 CLKREQPSON_ATX-
USB2
USB2_N
7
8
USB2_P
USB2
USB3
USB3_N
9
10
USB3_P
USB3 Ground
11
12
Ground
PS/2 MS
PS2_MSCLK
13
14
PS2_MSDATA
PS/2 MS
PS/2 KB
PS2_KBCLK
15
16
PS2_KBDATA
PS/2 KB
COM6
(UART)
COM6_RI
17
18
COM6_DCD-
COM6
(UART)
COM6_TXD
19
20
COM6_RXD
COM6_DTR
21
22
RICOM6_RTS-
COM6_DSR
23
24
COM6_CTS-
Ground
25
26
Ground
COM5
(UART)
COM5_RI
27
28
COM5_DCD-
COM5
(UART)
COM5_TXD
29
30
COM5_RXD
COM5_DTR
31
32
DSRCOM5_RTS-
COM5_DSR
33
34
DTRCOM5_CTS-
GPIO24
ICH_GPIO24
35
36
ICH_GPIO13
GPIO13
GPIO26
ICH_GPIO26
37
38
ICH_GPIO27
GPIO27
37. CN3:
(1.27mm Pitch 2X30 Pin Header), For expand output connector, It provides four GPIO,
two USB 2.0,one PS/2 mouse，one PS/2 keyboard, two uart,one PCIe x1,one SMbus.
connected to the TB-528 riser Card.
APC-3x93P_R (SBC-7106A) User Manual
25
Ground
39
40
Ground
PCIE
PE1_TX_N0
41
42
PE1_TX_P0
PCIE
PE1_RX_N0
43
44
PE1_RX_P0
Ground
45
46
Ground
CLK_100M_PE1_N
47
48
CLK_100M_PE1_P
PM_PCIE_WAKE
49
50
PLTRST_BUF-
SMBUS
SMB_CLK_S5
51
52
SMB_DATA_S5
SMBUS
PCIE
PE1_CLKREQ
53
54
Ground
3P3V_S5
55
56
PWRBTN_ON-
Power Auto on
3P3V_S5
57
58
3P3V_S5
12V
12V_S0
59
60
12V_S0
12V
Signal Name
Function support
PCIe 1X
Yes
USB2.0 (USB2)
Yes
SMBus
Yes
SIM
Yes
38. TB-528C2ME1 (option):
SBC-7106A Riser Card,TB-528C2ME1 CN3 connect to SBC-7106A CN3 pin Header.
TB-528C2ME1 Top：
CN3：
(1.27mm Pitch 2X30 Pin Header),connect to SBC-7106A CN3 pin Header.
M-PCIE1：
(Socket 52Pin),mini PCIe socket, it is located at the top, it supports mini PCIe devices
with USB2.0(USB2),Smbus,SIM and PCIe signal. MPCIe card size is 30x30mm or
30x50.95mm.
APC-3x93P_R (SBC-7106A) User Manual
26
H1/H2:
Pin#
Signal Name
1
KBDATA
2
MSDATA
3
Ground
4
+5V
5
KBCLK
6
MSCLK
Signal Name
Pin#
Pin#
Signal Name
Ground
1
2
NC
NC
3 4 SMB_DATA_R
SMB_CLK_R
5 6 ICH_GPIO13_IN1
ICH_GPIO24_IN2
7 8 ICH_GPIO26_IN3
ICH_GPIO27_IN4
9
10
+5V
Signal Name
Pin#
Pin#
Signal Name
5V_USB23
1 2 5V_USB23
USB3_N
3
4
USB2_N（option, NC）
USB3_P
5
6
USB2_P（option, NC）
MPCIE1 SCREW HOLES, H2 for mini PCIE card (30mmx30mm) assemble. H1 for mini
PCIE card (30mmx50.95mm) assemble.
LED1：
Mini PCIe devices LED Status.
SIM1：
(SIM Socket 6 Pin), Support SIM Card devices.
PS2：
(2.0mm Pitch 1X6 Pin Wafer), PS/2 keyboard and mouse port, the port can be
connected to PS/2 keyboard or mouse via a dedicated cable for direct used.
GPIO1：
(2.0mm Pitch 2x5 Pin Header),General-purpose input/output port, it provides a group of
self-programming interfaces to customers for flexible use.
USB_23：
(2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides one USB port via a
dedicated USB cable, speed up to 480Mb/s.
APC-3x93P_R (SBC-7106A) User Manual
27
Ground
7
8
Ground
NC
9
10
Ground
Note:
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
NA
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
Before connection, make sure that pinout of the USB Cable is in accordance with that of
the said tables. Any inconformity may cause system down and even hardware damages.
COM5：
(Type DB9),serial port, standard DB9 serial port is provided to make a direct connection
to serial devices. COM5 port is controlled by pins No.1~6 of JP5,select output Signal RI
or 5V or 12v, For details, please refer to description of JP3.
COM6：
(Type DB9),serial port, standard DB9 serial port is provided to make a direct connection
to serial devices. COM6 port is controlled by pins No.1~6 of JP6,select output Signal RI
or 5V or 12v, For details, please refer to description of JP6.
APC-3x93P_R (SBC-7106A) User Manual
28
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
NA
Signal Name
Pin#
Pin#
Signal Name
DCD
1 2 RXD
TXD
3 4 DTR
Ground
5 6 DSR
RTS
7
8
CTS
JP6 Setting: RI/5V/12V
9
10
NC
COM_6（option）：
(2.0mm Pitch 2X5 Pin Header),COM6 Port, up to one standard RS232 port are provided.
They can be used directly via COM cable connection.
39. TB-528C2 (option):
SBC-7106A Riser Card,TB-528C2ME1 CN3 connect to SBC-7106A CN3 pin Header.
TB-528C2ME1 Top：
CN3：
(1.27mm Pitch 2X30 Pin Header),connect to SBC-7106A CN3 pin Header.
LED1：
Mini PCIe devices LED Status.
PS2：
(2.0mm Pitch 1X6 Pin Wafer), PS/2 keyboard and mouse port, the port can be
APC-3x93P_R (SBC-7106A) User Manual
29
connected to PS/2 keyboard or mouse via a dedicated cable for direct used.
Pin#
Signal Name
1
KBDATA
2
MSDATA
3
Ground
4
+5V
5
KBCLK
6
MSCLK
Signal Name
Pin#
Pin#
Signal Name
Ground
1
2
NC
NC
3 4 SMB_DATA_R
SMB_CLK_R
5 6 ICH_GPIO13_IN1
ICH_GPIO24_IN2
7 8 ICH_GPIO26_IN3
ICH_GPIO27_IN4
9
10
+5V
Signal Name
Pin#
Pin#
Signal Name
5V_USB23
1 2 5V_USB23
USB3_N
3 4 USB2_N
USB3_P
5 6 USB2_P
Ground
7 8 Ground
NC
9
10
Ground
GPIO1：
(2.0mm Pitch 2x5 Pin Header),General-purpose input/output port, it provides a group of
self-programming interfaces to customers for flexible use.
USB_23：
(2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides one USB port via a
dedicated USB cable, speed up to 480Mb/s.
Note:
Before connection, make sure that pinout of the USB Cable is in accordance with that of
the said tables. Any inconformity may cause system down and even hardware damages.
COM5：
(Type DB9),serial port, standard DB9 serial port is provided to make a direct connection
to serial devices. COM5 port is controlled by pins No.1~6 of JP5,select output Signal RI
or 5V or 12v, For details, please refer to description of JP3.
APC-3x93P_R (SBC-7106A) User Manual
30
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
NA
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
NA
Signal Name
Pin#
Pin#
Signal Name
DCD
1 2 RXD
TXD
3 4 DTR
COM6：
(Type DB9),serial port, standard DB9 serial port is provided to make a direct connection
to serial devices. COM6 port is controlled by pins No.1~6 of JP6,select output Signal RI
or 5V or 12v, For details, please refer to description of JP6.
COM_6（option）：
(2.0mm Pitch 2X5 Pin Header),COM6 Port, up to one standard RS232 port are
provided. They can be used directly via COM cable connection.
APC-3x93P_R (SBC-7106A) User Manual
31
Ground
5 6 DSR
RTS
7
8
CTS
JP6 Setting: RI/5V/12V
9
10
NC
Signal Name
Function support
PCIe 1X
Yes
USB2.0 (USB2)
NC (option)
SMBus
Yes
SIM
Yes
40. TB-528C1U2P1/TB-528C1U2 (option):
SBC-7106A Riser Card,TB-528C1U2P1 CN3 connect to SBC-7106A CN3 pin Header.
TB-528C1U2P1 Top：
CN3：
(1.27mm Pitch 2X30 Pin Header),connect to SBC-7106A CN3 pin Header.
M-PCIE1：
(Socket 52Pin),mini PCIe socket, it is located at the top, it supports mini PCIe devices
with Smbus,SIM and PCIe signal. MPCIe card size is 30x30mm or 30x50.95mm.
H1/H2:
MPCIE1 SCREW HOLES, H2 for mini PCIE card (30mmx30mm) assemble. H1 for mini
PCIE card (30mmx50.95mm) assemble.
LED1：
Mini PCIe devices LED Status.
APC-3x93P_R (SBC-7106A) User Manual
32
SIM1（option）：
PS_ON
Mode
Close 1-2
Auto Power on (Default)
Open 1-2
ATX Power
PS_ON2
SBC-7106A /JP5
Pin1
Pin1
Pin2
Pin2
Pin#
Signal Name
1
KBDATA
2
MSDATA
3
Ground
4
+5V
5
KBCLK
6
MSCLK
Signal Name
Pin#
Pin#
Signal Name
Ground
1
2
NC
NC
3 4 SMB_DATA_R
SMB_CLK_R
5 6 ICH_GPIO13_IN1
ICH_GPIO24_IN2
7 8 ICH_GPIO26_IN3
ICH_GPIO27_IN4
9
10
+5V
(SIM Socket 6 Pin), Support SIM Card devices.
PS_ON1：
(2.0mm Pitch 1X2 Pin Wafer), ATX Power and Auto Power on jumper setting.
PS_ON2（option）：
(2.0mm Pitch 1X2 Pin Wafer),They can be used directly via cable connection to
SBC-7106A JP5.
PS2：
(2.0mm Pitch 1X6 Pin Wafer), PS/2 keyboard and mouse port, the port can be
connected to PS/2 keyboard or mouse via a dedicated cable for direct used.
GPIO1：
(2.0mm Pitch 2x5 Pin Header),General-purpose input/output port, it provides a group of
self-programming interfaces to customers for flexible use.
APC-3x93P_R (SBC-7106A) User Manual
33
USB23：
Signal Name
Pin#
Pin#
Signal Name
5V_USB23
1 2 5V_USB23
USB3_N
3 4 USB2_N
USB3_P
5 6 USB2_P
Ground
7 8 Ground
NC
9
10
Ground
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
NA
(Double stack USB type A), Rear USB connector, it provides up to 2 USB2.0 ports,
speed up to 480Mb/s.
USB_23（option）：
(2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides one USB port via a
dedicated USB cable, speed up to 480Mb/s.
Note:
Before connection, make sure that pinout of the USB Cable is in accordance with that of
the said tables. Any inconformity may cause system down and even hardware damages.
COM5：
(Type DB9),serial port, standard DB9 serial port is provided to make a direct connection
to serial devices. COM5 port is controlled by pins No.1~6 of JP5,select output Signal RI
or 5V or 12v, For details, please refer to description of JP3.
APC-3x93P_R (SBC-7106A) User Manual
34
COM6：
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
NA
S1
Model
Yes
TB-528C1U2P1
No
TB-528C1U2
(Type DB9),serial port, standard DB9 serial port is provided to make a direct connection
to serial devices. COM6 port is controlled by pins No.1~6 of JP6,select output Signal RI
or 5V or 12v, For details, please refer to description of JP6.
S1：
PWR BT: POWER on/off Button, They are used to connect power switch button. The
two pins are disconnected under normal condition. You may short them temporarily to
realize system startup & shutdown or awaken the system from sleep state.
PWR LED: POWER LED status.
41. TB-528CAN2 R0.10 (option):
SBC-7106A Riser Card,TB-528CAN2 CN3 connect to SBC-7106A CN3 pin Header.
It provides two CAN-bus Interface.
TB-528CAN2 Top：
APC-3x93P_R (SBC-7106A) User Manual
35
Signal Name
Function support
PCIe 1X
Yes
USB2.0 (USB2)
Yes
SMBus
Yes
SIM
Yes
CN3：
(1.27mm Pitch 2X30 Pin Header),connect to SBC-7106A CN3 pin Header.
M-PCIE1：
(Socket 52Pin),mini PCIe socket, it is located at the top, it supports mini PCIe devices
with Smbus,USB2.0,SIM and PCIe signal. MPCIe card size is 30x30mm or
30x50.95mm.
H1/H2:
MPCIE1 SCREW HOLES, H2 for mini PCIE card (30mmx30mm) assemble. H1 for mini
PCIE card (30mmx50.95mm) assemble.
LED1：
Mini PCIe devices LED Status.
SIM1（option）：
(SIM Socket 6 Pin), Support SIM Card devices.
PS2：
(2.0mm Pitch 1X6 Pin Wafer), PS/2 keyboard and mouse port, the port can be
APC-3x93P_R (SBC-7106A) User Manual
36
connected to PS/2 keyboard or mouse via a dedicated cable for direct used.
Pin#
Signal Name
1
KBDATA
2
MSDATA
3
Ground
4
+5V
5
KBCLK
6
MSCLK
Signal Name
Pin#
Pin#
Signal Name
5V_USB23
1 2 5V_USB23
NC (USB3_N)
3 4 NC (USB2_N)
NC (USB3_P)
5 6 NC (USB2_P)
Ground
7 8 Ground
NC
9
10
Ground
Signal Name
Pin#
Pin#
Signal Name
3P3V_S5_USB
1 2 3P3V_S5
3P3V_S5_USB
3 4 3P3V_S5
3P3V_S5_USB
5 6 3P3V_S5
PSON_ATX
7 8 Ground
PSON_ATX
9
10
Ground
Signal Name
Pin#
Pin#
Signal Name
DCD
1 2 RXD
USB_IN（option）：
(2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides two USB port via a
dedicated USB cable, speed up to 480Mb/s.
Note:
Before connection, make sure that pinout of the USB Cable is in accordance with that of
the said tables. Any inconformity may cause system down and even hardware damages.
JP_SET (option):
(2.0mm Pitch 2x5 Pin Header).
COM6：
(2.0mm Pitch 2X5 Pin Header),COM6 Port, up to one standard RS232 port are provided.
They can be used directly via COM cable connection.
APC-3x93P_R (SBC-7106A) User Manual
37
TXD
3 4 DTR
Ground
5 6 DSR
RTS
7
8
CTS
JP6 Setting：RI/5V/12V
9
10
NC
Signal Name
Pin#
Pin#
Signal Name
DCD
1 2 RXD
TXD
3 4 DTR
Ground
5 6 DSR
RTS
7
8
CTS
RI
9
10
NC
Signal Name
Pin#
Pin#
Signal Name
Ground
1
2
NC
NC
3 4 SMB_DATA_R
SMB_CLK_R
5 6 ICH_GPIO13_IN1
ICH_GPIO24_IN2
7 8 ICH_GPIO26_IN3
ICH_GPIO27_IN4
9
10
+5V
COM5:
(2.0mm Pitch 2X5 Pin Header),COM5 Port, up to one standard RS232 port are provided.
They can be used directly via COM cable connection.
GPIO1：
(2.0mm Pitch 2x5 Pin Header),General-purpose input/output port, it provides a group of
self-programming interfaces to customers for flexible use.
JTAG：
(2.0mm Pitch 2x5 Pin Header), Reserve.
JP1：
(2.0mm Pitch 1x2 Pin Header), Reserve.
JP2：
(2.0mm Pitch 1x2 Pin Header), Reserve.
CAN1/CAN2：
(3.5mm Pitch 1x10 Pin connector), it provides two CAN-bus Interface.
APC-3x93P_R (SBC-7106A) User Manual
38
Pin#
Channel
Signal Name
Function
1
CAN2
CANL2
CAN bus Signal L
2
R2-
Terminal resistor R-(internally connected to CANL2)
3
FG
Shield cable (FG)
4
R2+
Terminal resistor R+( internally connected to CANH2)
5
CANH2
CAN bus Signal H
6
CAN1
CANL1
CAN bus Signal L
7
R1-
Terminal resistor R-(internally connected to CANL1)
8
FG
Shield cable (FG)
9
R1+
Terminal resistor R+( internally connected to CANH1)
10
CANH1
CAN bus Signal H
【See TB-528AN2 Manual】
42. TB-528U2 (option):
SBC-7106A Riser Card,TB-528U2 CN3 connect to SBC-7106A CN3 pin Header.
TB-528U2 Top：
CN3：
(1.27mm Pitch 2X30 Pin Header),connect to SBC-7106A CN3 pin Header.
USB23：
(Double stack USB type A), Rear USB connector, it provides up to 2 USB2.0 ports,
speed up to 480Mb/s.
APC-3x93P_R (SBC-7106A) User Manual
39
Chapter 3 BIOS Setup
3.1 Operations after POST Screen
After CMOS discharge or BIOS flashing operation,.Press [Delete] key to enter CMOS Setup.
After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is as follows
and includes basic information on BIOS, CPU, memory, and storage devices.
3.2 BIOS Setup Utility
Press [Delete] key to enter BIOS Setup utility during POST, and then a main menu containing system
summary information will appear.
APC-3x93P_R (SBC-7106A) User Manual
40
3.3 Main Settings
APC-3x93P_R (SBC-7106A) User Manual
41
System Time:
Hour : 0 to 23
Minute : 0 to 59
Second : 0 to 59
Set the system time, the time format is:
System Date:
Set the system date, the date format is:
Day: Note that the ‘Day’ automatically changes when you set the date.
Month: 01 to 12
Date: 01 to 31
Year: 1998 to 2099
3.4 Advanced Settings
3.4.1 PCI Subsystem Settings
PCI Bus Driver Versio V2.05.02
PCI Common Settings:
PCI Latency Timer:
APC-3x93P_R (SBC-7106A) User Manual
42
[32 PCI Bus Clocks]
[64 PCI Bus Clocks]
[96 PCI Bus Clocks]
[128 PCI Bus Clocks]
[160 PCI Bus Clocks]
[192 PCI Bus Clocks]
[224 PCI Bus Clocks]
[248 PCI Bus Clocks]
VGA Palette Snoop:
[Disabled]
[Enabled]
PERR# Generation:
[Disabled]
[Enabled]
SERR# Generation:
[Disabled]
[Enabled]
3.4.2 ACPI Settings
Enable ACPI Auto Conf:
[Disabled]
[Enabled]
Enable Hibernation:
[Enabled]
[Disabled]
ACPI Sleep State:
[Both S1 and S3 available for OS to choose from ]
[Suspend Disabled]
[S1 only(CPU Stop Clock) ]
[S3 only (Suspend to RAM) ]
Lock Legacy Resources:
[Disabled]
[Enabled]
APC-3x93P_R (SBC-7106A) User Manual
43
S3 Video Repost:
Processer Type
Intel(R) Atom™ CPU D2550
EMT64
Supported
Processor Speed
1865 MHz
System Bus Speed
533MHz
Ratio Status
14
Actual Ratio
14
System Bus Speed
533 MHz
Processor Stepping
30661
Microcode Revision
269
L1 Cache RAM
2x56 k
L2 Cache RAM
2x512 k
Processor Core
Dual
Hyper-Threading
Supported
[Disabled]
[Enabled]
3.4.3 CPU Configuration
Hyper-Threading:
[Enabled]
[Disabled]
Execute Disable Bit:
[Enabled]
[Disabled]
Limit CPUID Maximum:
[Disabled]
[Enabled]
3.4.4 Thermal Configuration
CPU Thermal Configuration
DTS SMM
[Disabled]
[Enabled]
Platform Thermal Configuration
Critical Trip Point [POR]
Active Trip Point Lo [55 C]
APC-3x93P_R (SBC-7106A) User Manual
44
Active Trip Point Hi [71C]
Passive Trip Point [95]
Passive TC1 Value 1
Passive TC2 Value 5
Passive TSP Value 10
3.4.5 IDE Configuration
SATA Port0 Not Present
SATA Port1 Not Present
SATA Controller(S):
[Enabled]
[Disabled]
Configure SATA as:
[IDE]
[AHCI]
Misc Configuration for hard disk
3.4.6 USB Configuration
USB Configuration
USB Devices:
1 keyboard, 1 Mouse，1 Point
Legacy USB Support:
[Enabled]
[Disabled]
EHCI Hand-off:
[Disabled]
[Enabled]
USB hardware delays a
USB transfer time-out:
[20 sec]
[10 sec]
[5 sec]
[1 sec]
Device reset time-out:
[20 sec]
[10 sec]
[30 sec]
[40 sec]
Device power-up delay
APC-3x93P_R (SBC-7106A) User Manual
45
[Auto]
System temperature1
: +38
SystemFan Speed
: N/A
CPUFan Speed
: N/A
VCORE
: +1.224V
+12V
: +12.512V
+3.3V
: +3.2888V
+1.5V
: +1.528V
AVCC
: +5.203V
VCC5V
: +5.216V
VSB5
: +5.203V
VBAT
: +3.334V
[Manual]
3.4.7 W83627UHG Super IO Configuration
W83627UHG Super IO ch W83627UHG
Serial Port 1 Configuration
UART Mode Selection：
[RS-232]
[RS-485]
[RS-422]
Serial Port 2 Configuration
Serial Port 3 Configuration
UART Mode Selection：
[RS-485]
[RS-422]
Serial Port 4 Configuration
Serial Port 5 Configuration
Serial Port 6 Configuration
3.4.8 W83627UHG HW Monitor
PC Health Status
3.4.9 Serial Port Console Redirection
COM0
Console Redirection
APC-3x93P_R (SBC-7106A) User Manual
[Enabled]
46
[Disabled]
Console Redirection Settings
Serial Port for Out-of-Band Management/
Windows Emergency Management Services (EMS)
Console Redirection
[Disabled]
[Enabled]
Console Redirection Settings
3.4.10 PPM Configuration
PPM Configuration
EIST:
[Enabled]
[Disabled]
CPU C state Report
[Enabled]
[Disabled]
Enhanced C state
[Enabled]
[Disabled]
CPU Hard C4E
[Enabled]
[Disabled]
CPU C6 state
[Enabled]
[Disabled]
C4 Exit Timing
[Fast]
[Default]
[Slow]
C-state POPDOWN
[Enabled]
[Disabled]
C-state POPUP
[Enabled]
[Disabled]
APC-3x93P_R (SBC-7106A) User Manual
47
3.5 Chipset Settings
3.5.1 Host Bridge
►Memory Frequency and Timing
►Intel IGD Configuration
******* Memory Information *******
Memory Frequency 1067 MHz(DDR3)
Total Memory 4096 MB
DIMM#0 Not Present
DIMM#1 4096 MB
Memory Frequency and Timing
MRC Fast Boot
[Enabled]
[Disabled]
Max TOLUD
[1GB]
[1.25GB]
APC-3x93P_R (SBC-7106A) User Manual
[Dynamic]
48
[1.5GB]
[1.75GB]
[2GB]
[2.25GB]
[2.5GB]
[2.75GB]
[3GB]
[3.25GB]
Intel IGD Configuration
IGFX – Boot Type
[VBIOS Default]
[VGA]
[HDMI]
[LVDS]
LCD Panel Type
Panel Scaling
Active LFP
IGD Clock Source
Fixed Graphics Memory
ALS Support
[VBIOS Default]
[Auto]
[Force Scaling]
[off]
[Maintain Aspect Ratio]
[LVDS]
[No LVDS]
[External Clock]
[Internal Clock]
[128MB]
[256MB]
[Enabled]
Back light Control
Back light Logic
APC-3x93P_R (SBC-7106A) User Manual
[Disabled]
[DC]
[PWM]
[Positive]
49
Back light Control Lev
[Negative]
[Level 8]
[Level 1]
[Level 2]
[Level 3]
[Level 4]
[Level 5]
[Level 6]
[Level 7]
[Level 9]
[Level 10]
[Level 11]
[Level 12]
[Level 13]
[Level 14]
[Level 15]
3.5.2 South Bridge
TPT Devices
PCI Express Root Port 0
PCI Express Root Port 1
PCI Express Root Port 2
PCI Express Root Port 3
DMI Link ASPM Control
[Enabled]
[Disabled]
PCI-Exp. High Priorit
[Disabled]
[Enabled]
High Precision Event Timer Configuration
High Precision Timer
[Enabled]
[Disabled]
SLP_S4 Assertion Widt
APC-3x93P_R (SBC-7106A) User Manual
[1-2 Seconds]
[2-3 Seconds]
[3-4 Seconds]
[4-5 Seconds]
50
3.6 Boot Settings
Setup Prompt Timeout [1]
Bootup Numlock State
[On]
[off]
Quiet Boot
[Disabled]
[Enabled]
Fast Boot
[Enabled]
[Disabled]
Skip VGA
APC-3x93P_R (SBC-7106A) User Manual
51
[Enabled]
[Disabled]
Skip USB
[Disabled]
[Enabled]
Skip PS2
[Disabled]
[Enabled]
CSM16 Module Version 07.69
Gatea20 Active
[Upon Request]
[Always]
Option ROM Messages
[Force BIOS]
[Keep Current]
Interrupt 19 Capture
[Immediate]
[Postponed]
Boot Option #1
Boot Option #2
……
Sets the system boot order
Hard Drive BBS Priorities [SATA PM:*** … ]
Boot Option #1
SATA PM:***…
******
Disabled
CSM Parameters
Launch CSM
[Always]
[Never]
Boot option filter
[UEFI and Legacy]
[Legacy only]
[UEFI only]
Launch PXE OpROM poli
[Do not Launch]
[UEFI only]
[Legacy only]
Launch Storage OpROM
[Legacy only]
APC-3x93P_R (SBC-7106A) User Manual
52
[Do not Launch]
[UEFI only]
Launch Video OpROM po
[Legacy only]
[Do not Launch]
[UEFI only]
Other PCI device ROM
[UEFI OpROM]
[Legacy OpROM]
3.7 Security Settings
3.7.1 Administrator Password
3.7.2 User Password
APC-3x93P_R (SBC-7106A) User Manual
53
Type the password with up to 20 characters and then press Enter key. This will clear all
previously typed CMOS passwords. You will be requested to confirm the password. Type the
password again and press Enter key. You may press Esc key to abandon password
entry operation.
To clear the password, just press Enter key when password input window pops up. A
confirmation message will be shown on the screen as to whether the password will be
disabled. You will have direct access to BIOS setup without typing any password after system
reboot once the password is disabled.
Once the password feature is used, you will be requested to type the password each time you
enter BIOS setup. This will prevent unauthorized persons from changing your system
configurations.
Also, the feature is capable of requesting users to enter the password prior to system boot to
control unauthorized access to your computer. Users may enable the feature in Security
Option of Advanced BIOS Features. If Security Option is set to System, you will be requested
to enter the password before system boot and when entering BIOS setup; if Security Option is
set to Setup, you will be requested for password for entering BIOS setup.
3.8 Save & Exit Settings
APC-3x93P_R (SBC-7106A) User Manual
54
Save Changes and Exit
Save & Exit Setup save Configuration and exit ?
[Yes]
[No]
Discard Changes and Ext
Exit Without Saving Quit without saving?
[Yes]
[No]
Save Changes and Reset
Save & reset Save Configuration and reset?
[Yes]
[No]
Discard Changes and Reset
Reset Without Saving Reset without saving?
[Yes]
[No]
Save Changes
Save Setup Values Save configuration?
[Yes]
[No]
Discard Changes
Load Previous Values Load Previous Values?
[Yes]
[No]
Restore Defaults
Load Optimized Defaults Load optimized Defaults?
[Yes]
[No]
Save user Defaults
Save Values as User Defaults Save configuration?
[Yes]
[No]
Restore user Defaults
Restore User Defaults Restore User Defaults?
[Yes]
Launch EFI Shell from filesystem device
WARNING Not Found
[ok]
APC-3x93P_R (SBC-7106A) User Manual
[No]
55
Chapter 4 Installation of Drivers
Important Note:
After installing your Windows operating system, you must install first the Intel
Chipset Software Installation Utility before proceeding with the installation of
drivers.
This chapter describes the installation procedures for software and drivers under the windows 7. The
software and drivers are included with the motherboard. The contents include Intel chipset driver,
VGA driver, LAN drivers, Audio driver Installation instructions are given below.
I
APC-3x93P_R (SBC-7106A) User Manual
56
4.1 Intel Chipset Driver
To install the Intel chipset driver, please follow the steps below.
Step 1. Select Intel (R) Chipset NM10 Express from the list
Step 2. Click Next to setup program.
APC-3x93P_R (SBC-7106A) User Manual
57
Step 3. Read the license agreement. Click Yes to accept all of the terms of the license agreement.
Step 4. Click Next to continue.
APC-3x93P_R (SBC-7106A) User Manual
58
Step 5. Click Next.
Step 6. Select Yes, I want to restart this computer now. Click Finish, then remove any installation
media from the drives.
APC-3x93P_R (SBC-7106A) User Manual
59
4.2 Intel Graphics Media Accelerator Driver
To install the VGA drivers, follow the steps below to proceed with the installation.
Step 1.Select Intel(R) VGA Chipset Driver.
Step 2. Tick Automatically run WinSAT and enable the Windows Aero desktop theme(if
supported). Click Next.
APC-3x93P_R (SBC-7106A) User Manual
60
Step 3. Read license agreement. Click Yes.
Step 4. Click Next.
APC-3x93P_R (SBC-7106A) User Manual
61
Step 5. Click Next.
Step 6. To restart the computer, select Yes, I want to restart this computer now. Then click
Finish.
APC-3x93P_R (SBC-7106A) User Manual
62
4.3 Intel (R) Network Adapter
To install the Intel (R) Network Adapter device driver, please follow the steps below.
Step 1. Select LAN Driver.
Step 2. Select 17”~19”.
APC-3x93P_R (SBC-7106A) User Manual
63
Step 3. Click Next to Continue.
Step 4. Read license agreement. Click I accept the terms in the license agreement.
Click Next
APC-3x93P_R (SBC-7106A) User Manual
64
Step 5. Click Advanced Network Services. Then click Next to Continue.
Step 6. Click Install to begin the installation.
APC-3x93P_R (SBC-7106A) User Manual
65
Step 7. Click Finish to exit the wizard.
4.4 Realtek ALC662 HD Audio Codec Driver Installation
To install the Realtek ALC662 HD Audio Codec Driver, please follow the steps below.
Step 1. Select Realtek AL662 Audio Codec Driver from the list
APC-3x93P_R (SBC-7106A) User Manual
66
Step 2. Click Next to continue.
Step 3. Click Yes, I want to restart my computer now. Click Finish to complete the installation.
APC-3x93P_R (SBC-7106A) User Manual
67
Chapter 5 Touch Screen Installation
This chapter describes how to install drivers and other software that will allow your touch screen work
with different operating systems.
5.1 Windows 2000/2003/Vista/WIN7 Universal Driver
Installation for PenMount 6000 Series
Before installing the Windows 2000/WIN7 driver software, you must have the Windows 2000/WIN 7
system installed and running on your computer. You must also have one of the following PenMount
6000 series controller or control boards installed: PM6500, PM6300.
5.1.1 Installing Software(Resistive Touch)
If you have an older version of the PenMount Windows 2000/WIN7 driver installed in your system,
please remove it first. Follow the steps below to install the PenMount DMC6000 Windows 2000/WIN7
driver.
Step 1. Insert the product CD, the screen below would appear. Click touch panel driver.
APC-3x93P_R (SBC-7106A) User Manual
68
Step 2. Select Resistive Touch.
Step 3. Click Next to continue.
APC-3x93P_R (SBC-7106A) User Manual
69
Step 4. Read the license agreement. Click I Agree to agree the license agreement.
Step 5. Choose the folder in which to install PenMount Windows Universal Driver. Click Install to
start the installation.
APC-3x93P_R (SBC-7106A) User Manual
70
Step 6. Wait for installation. Then click Next to continue.
Step 7. Click Continue Anyway.
APC-3x93P_R (SBC-7106A) User Manual
71
Step 8. Click Finish to complete installation.
5.1.2 Installing Software (Projected Capacitive)
Step 1. Insert the product CD, the screen below would appear. Click touch panel driver.
APC-3x93P_R (SBC-7106A) User Manual
72
Step 2. Select Projected Capacitive.
Step 3. Click Next to continue.
APC-3x93P_R (SBC-7106A) User Manual
73
Step 4. Select I accept the terms of the license agreement. Click Next.
Step 5. Tick Install RS232 interface driver. Click Next.
APC-3x93P_R (SBC-7106A) User Manual
74
Step 6. Select None. Click Next.
Step 7. Click OK.
Step 8. Tick Support Muti-Monitor System. Click Next.
APC-3x93P_R (SBC-7106A) User Manual
75
Step 9. Go to C:\Program Files\eGalaxTouch. Click Next.
Step 10. Click Next.
APC-3x93P_R (SBC-7106A) User Manual
76
Step 11. Tick Create a eGalaxTouch Utility shortcut on desktop. Click Next.
Step 12. Wait for installation.
APC-3x93P_R (SBC-7106A) User Manual
77
Step 13. Click Yes to do 4 point calibration.
5.2 Software Functions
5.2.1 Software Functions(Resistive Touch)
Upon rebooting, the computer automatically finds the new 6000 controller board. The touch screen is
connected but not calibrated. Follow the procedures below to carry out calibration.
1. After installation, click the PenMount Monitor icon “PM” in the menu bar.
2. When the PenMount Control Panel appears, select a device to “Calibrate.”
PenMount Control Panel(Resistive Touch)
The functions of the PenMount Control Panel are Device, Multiple Monitors ,Tools and About,
which are explained in the following sections.
Device
In this window, you can find out that how many devices be detected on your system.
Calibrate
This function offers two ways to calibrate your touch screen. ‘Standard Calibration’ adjusts most touch
screens. ‘Advanced Calibration’ adjusts aging touch screens.
APC-3x93P_R (SBC-7106A) User Manual
78
Standard Calibration
Click this button and arrows appear pointing to
red squares. Use your finger or stylus to touch
the red squares in sequence. After the fifth red
point calibration is complete. To skip, press
‘ESC’.
Advanced Calibration
Advanced Calibration uses 4, 9, 16 or 25 points
to effectively calibrate touch panel linearity of
aged touch screens. Click this button and
touch the red squares in sequence with a
stylus. To skip, press ESC’.
Command Calibration
Command call calibration function. Use
command mode call calibration function, this
can uses Standard, 4, 9, 16 or 25 points to
calibrate E.g. Please run ms-dos prompt or
command prompt c:\Program Files\PenMount
Universa Driver\Dmcctrl.exe -calibration 0
( Standard Calibration) Dmcctrl.exe - calibration
($) 0= Standard Calibration 4=Advanced
Calibration 4 9=Advanced Calibration 9
16=Advanced Calibration 16 25=Advanced
Calibration 25
Step 1. Please select a device then click “Configure”. You can also double click the device too.
APC-3x93P_R (SBC-7106A) User Manual
79
Step 2.Click “Standard Calibration” to start calibration procedure
NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an
accurate calibration. Use a stylus during Advanced Calibration for greater accuracy. Please follow the
step as below:
APC-3x93P_R (SBC-7106A) User Manual
80
Step 3.Come back to “PenMount Control Panel” and select Tools then click Advanced
Calibration.
Step 4. Select Device to calibrate, then you can start to do Advanced Calibration.
NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy.
APC-3x93P_R (SBC-7106A) User Manual
81
Plot Calibration Data
Check this function and a touch panel linearity
comparison graph appears when you have finished
Advanced Calibration. The blue lines show linearity
before calibration and black lines show linearity
after calibration.
Turn off EEPROM storage
The function disable for calibration data to write in
Controller. The default setting is Enable.
Setting
Touch Mode
This mode enables and disables the mouse’s ability to drag
on-screen icons – useful for configuring POS terminals.
Mouse Emulation – Select this mode and the mouse
functions as normal and allows dragging of icons.
Click on Touch – Select this mode and mouse only provides
a click function, and dragging is disables.
Beep Sound
Enable Beep Sound – turns beep function on and off
Beep on Pen Down – beep occurs when pen comes down
Beep on Pen Up – beep occurs when pen is lifted up
Beep on both – beep occurs when comes down and lifted up
Beep Frequency – modifies sound frequency
Beep Duration – modifies sound duration
Cursor Stabilizer
Enable the function support to prevent cursor shake.
Use press and hold
as right click
You can set the time out and area for you need.
APC-3x93P_R (SBC-7106A) User Manual
82
About
This panel displays information about the PenMount controller and driver version.
APC-3x93P_R (SBC-7106A) User Manual
83
Multiple Monitors
Multiple Monitors support from two to six touch screen displays for one system. The PenMount drivers
for Windows 2000/WIN 7 support Multiple Monitors. This function supports from two to six touch
screen displays for one system. Each monitor requires its own PenMount touch screen control board,
either installed inside the display or in a central unit. The PenMount control boards must be connected
to the computer COM ports via the RS-232 interface. Driver installation procedures are the same as
for a single monitor. Multiple Monitors support the following modes:
Windows Extends Monitor Function
Matrox DualHead Multi-Screen Function
nVidia nView Function
NOTE: The Multiple Monitor function is for use with multiple displays only. Do not use this function if
you have only one touch screen display. Please note once you turn on this function the rotating
function is disabled.
Enable the multiple display function as follows:
1. Check the Enable Multiple Monitor Support box; then click Map Touch Screens to assign touch
controllers to displays.
APC-3x93P_R (SBC-7106A) User Manual
84
2. When the mapping screen message appears, click OK.
3. Touch each screen as it displays “Please touch this monitor”. Following this sequence and
touching each screen is called mapping the touch screens.
4. Touching all screens completes the mapping and the desktop reappears on the monitors.
5. Select a display and execute the “Calibration” function. A message to start calibration appears.
Click OK.
APC-3x93P_R (SBC-7106A) User Manual
85
6. “Touch this screen to start its calibration” appears on one of the screens. Touch the screen.
7. “Touch the red square” messages appear. Touch the red squares in sequence.
8. Continue calibration for each monitor by clicking Standard Calibration and touching the red
squares.
NOTES: 1. If you use a single VGA output for multiple monitors, please do not use the Multiple
Monitor function. Just follow the regular procedure for calibration on each of your
desktop monitors.
2. The Rotating function is disabled if you use the Multiple Monitor function.
3. If you change the resolution of display or screen address, you have to redo Map Touch
Screens, so the system understands where the displays are.
About
This panel displays information about the PenMount controller and this driver version.
PenMount Monitor Menu Icon
The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/WIN7 system when you
turn on PenMount Monitor in PenMount Utilities.
PenMount Monitor has the following function
APC-3x93P_R (SBC-7106A) User Manual
86
Control Panel
Open Control Panel Windows
Beep
Setting Beep function for each device
Right Button
When you select this function, a mouse icon appears in
the right-bottom of the screen.
Click this icon to switch between Right and Left Button
functions.
Exit
Exits the PenMount Monitor function.
PenMount Rotating Functions
The PenMount driver for Windows 2000/WIN7 supports several display rotating software packages.
Windows Me/2000/WIN7 support display rotating software packages such as:
• Portrait’s Pivot Screen Rotation Software
• ATI Display Driver Rotate Function
• nVidia Display Driver Rotate Function
• SMI Display Driver Rotate Function
• Intel 845G/GE Display Driver Rotate Function
Configuring the Rotate Function
1. Install the rotation software package.
2. Choose the rotate function (0°, 90°, 180°, 270°) in the 3rd party software. The calibration screen
appears automatically. Touch this point and rotation is mapped.
NOTE: The Rotate function is disabled if you use Monitor Mapping
APC-3x93P_R (SBC-7106A) User Manual
87
5.2.2 Software Functions(Projected Capacitive)
General
In this window, you can see there is USB Controller. Click OK to continue.
Monitor Mapping
to adjust touch panel
Add
to search for device
APC-3x93P_R (SBC-7106A) User Manual
88
Setting
Beep
Beep On Touch
Beep On Release
Beep From System Beep
Beep From Sound Card
Linearization Style
9 points
25 points
Double Click Time
Shorter
Longer
Double Click Area
Smaller
Bigger
APC-3x93P_R (SBC-7106A) User Manual
Normal mode
Simulate the mouse mode
89
Option
Function
Enable Constant Touch
Enable Auto Right Click
Enable Touch
Enable Cursor Stabilization
Constant Touch Area
Auto Right Click Time
APC-3x93P_R (SBC-7106A) User Manual
90
Tools
Click OK to continue the settings.
4 Points Calibration
Do 4 points alignment to match display.
Clear and Calibrate
Clear linearization parameter and do 4 points alignment.
Linearization
Do 9 points linearization for better touchscreen linearity.
Draw Test
Do draw test to verify the touch accuracy.
APC-3x93P_R (SBC-7106A) User Manual
91
Display
In this window, it shows the mode of display.
Enable Multiple Monitors.
Map to main display if system has only one display monitor
Full Screen
Lower Screen
Left Screen
Upper Screen
Right Screen
APC-3x93P_R (SBC-7106A) User Manual
92
Other
Other mode of display. Quarter1~4 and Customized area.
Active Area
Drag active area to enable Active Area Function.
APC-3x93P_R (SBC-7106A) User Manual
93
Hardware
Saturn Hardware Configuration
APC-3x93P_R (SBC-7106A) User Manual
94
About
To display information about eGalaxTouch and its version.
APC-3x93P_R (SBC-7106A) User Manual
Loading...