Aplex ADP-1158P User Manual

1
ADP-1XX8P Display
User Manual
Release Date Revision
Nov. 2013 V1.1
® 2013 Aplex Technology, Inc. All Rights Reserved. Published in Taiwan
Aplex Technology, Inc. 15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: aplex@aplex.com.tw URL: www.aplex.com.tw
ADP-1XX8P User Manual
2
Warning!___________________________________
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, it may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
Electric Shock Hazard – Do not operate the machine with its back cover removed. There are dangerous high voltages inside.
Disclaimer
This information in this document is subject to change without notice. In no event shall Aplex Technology Inc. be liable for damages of any kind, whether incidental or consequential, arising from either the use or misuse of information in this document or in any related materials.
ADP-1XX8P User Manual
3
Table of Contents______________________
Warning!…………………………………………………………………………….……...2 Disclaimer………………………………………………………………….…………………2
Chapter 1 Getting Started
1.1 Features………………………………………………..………….………….5
1.2 Specifications…………………………………………. ...……………...….5
1.3 Dimensions…………………………………...………………………….6
1.4 Brief Description...................................................................................8
1.5 Display Mode……………………………………………………………….9
Chapter 2 OSD
2.1 Front Panel OSD Functions.…………………………………...10
2.2 OSD Controls…………………..…………………………………………..11
2.3 Main Menu..………..……………………………………………………..12
2.4 AD Board (VA-3600) OSD Functions…….………………………………14
Chapter 3 Control Board
3.1 Introduction to Control Board……………….……………………………..15
3.4 Installation of Control Board……………………………………………...15
Chapter 4 Installation
4.1 Windows 2000/XP Driver Installation…………………………………….16
4.2 Configuring eGalax Windows 2000/XP Driver………………………17
Chapter 5 Software
5.1 Software Functions………………………………………………………..22
ADP-1XX8P User Manual
4
Figures
Figure 1.1: Dimensions of ADP-1158P………………………..………………..6 Figure 1.2: Dimensions of ADP-1198P……………………..…………………..7 Figure 1.3: Front View of ADP-1XX8P………………………………………….8 Figure 1.4: Rear View of ADP-1XX8P………………………………………….8 Figure 3.1: Bird Eyes View of Control Board………………………………15
ADP-1XX8P User Manual
5
Chapter 1_____________________________
Environment
Model No.
ADP-1158P
ADP-1198P
Operating
Temperature
-20~60˚C
0~50˚C
Storage
Temperature
-20~70˚C
-20~60˚C
Storage Humidity
10~90% @40˚C non-condensing
Vibration
1G peak, 5~500Hz (at random)
Certifications
CE/FCC Class A
Shock
15G peak acceleration (11msec. duration)/operation
Display
Model No.
ADP-1158P
ADP-1198P
Display
15” 1024x768 color TFT LCD
19” 1280x1024 color TFT LCD
Luminance
400 nits
350 nits
1000 nits(optional)
Touch point feature
2 fingers touch
Viewing Angle
H: 160 / V: 145
H: 170 / V: 160
Resolution
1024x768
1280x1024
Backlight
Lifetime
50,000 hrs
Touch Screen
Projected Capacitive touch
Light Transmission
90%
OSD
On rear side default, on front side optional
Power Input
11~32V/DC
Outside I/O port
VGA X1 DVI X1 AV X1 S-Video X1 3 pins Terminal block power input 1XUSB for touch
1.1 Features
Flat Panel Design
Aluminum front Bezel and Steel Chassis
Projected Capacitive Touch
OSD Keypad Control at rear side, front side for option
Wide Range 11~32V DC Power Input
1.2 Specifications
ADP-1XX8P User Manual
6
Mechanical
Model No.
ADP-1158P
ADP-1198P
Construction
Aluminum Sliver front/Steel Black Back
Dimensions
410x333.6x42
484x416.07x42
IP Rating
Front Panel IP65
Mounting
Panel Mount / VESA Mount 75x75
Panel Mount / VESA Mount 100x100
1.3 Dimensions
Figure 1.1: Dimensions of ADP-1158P
ADP-1XX8P User Manual
7
Figure 1.2: Dimensions of ADP-1198P
ADP-1XX8P User Manual
8
1.4 Brief Description of ADP-1xx8 P
ADP-1XX8P is a TFT LCD monitor and more outstanding features, thus giving you the best in monitoring and control applications. The front panel of the display monitor is sealed with IP 65 rating when it is panel-mounted in a NEMA rated cabinet or enclosure. It can also be VESA 75-mounted for ADP-1158P or VESA 100-mounted for ADP-1198P. It is to be equipped with a projected capacitive touch screen.
Figure 1.3: Front View of ADP-1XX8P
Figure 1.4: Rear View of ADP-1XX8P
ADP-1XX8P User Manual
9
1.5 Display Mode
Display Mode
Hori. Sync (KHz)
Vert. Sync. (Hz)
31
60
VGA 640 x 480
38
72 38
75 35
56
SVGA 800 x 600
38
60 48
72 47
75 48
60
XGA 1024 x 768
56
70 60
75
SXGA
1152 x 864
68
75
1280 x 1024
64
60
80
75
Full HD 1920 x 1080
75
60
ADP-1XX8P User Manual
10
Chapter 2_____________________________
Cable Not Connected
2.1 Front Panel OSD Functions
Auto Adjust Up/Left Down/Right Power
Menu/Entry Power Indicator
Power switch: To turn ON or OFF the power
Shift the icon to the right side or shift it up
Shift the icon to the left side or shift it down
Menu: To enter OSD menu for related icon and item.
Auto Button: One-touch auto adjustment
1.) Getting into Burn-in Mode
Before setting into a burn-in mode, first disconnect the AC power cord. Then press (dont let them go) the buttons until the AC power cord is connected and the “RGB” appears on the top left corner
of your screen. Now it can be put into the burn-in mode for changing colors.
2.) Getting Out of Burn-in Mode
Before getting out of the burn-in mode, please first disconnect the AC power cord. Then press the button (If not workable, press the button and dont let them go) until the AC power cord is connected. Please dont let your fingers go until the AC power cord is connected again and the wording of RGB appears on the top left corner of your screen, and wait for 3 seconds. Under the non-signal entry situation, if is seen, exit is thus successfully made.
ADP-1XX8P User Manual
11
2.2 OSD Controls
To make any adjustment, select the following:
1. Press (Menu) to show the OSD menu or disable the OSD menu.
2. Select the icon that you wish to adjust with the ( / or +/-) key in the menu.
3. Press (Menu) and then choose the item with the ( / or +/-) key.
4. Press (Menu) and then adjust the quality with the ( / or +/-) key.
1.) If the RGB is still on the top left corner of the screen, press to enter Miscellaneous and
choose Reset, and then Yes, and press . When the screen goes black, disconnect power and repeat the above steps.
2.) If the RGB is not found, disconnect the AC power cord first. Then press the buttons (dont let them go) until the AC power cord is connected, and wait for 2 to 3 seconds. When
RGB appears, repeat the above steps.
3.) Functions of OSD Keys
ADP-1XX8P User Manual
12
2.3 Main Menu
In the Main menu, there are the following items:
Color Image Setting Position OSD Menu Language Misc Exit
For Color, check out the following:
Contrast Brightness Color Adjust Color Temp Back
For Image setting, check out the following:
Clock Phase Gamma Sharpness Back
ADP-1XX8P User Manual
13
In the Position, there are the following:
H. Position V. Position Back
In the OSD menu, there are:
OSD H. Pos. OSD V. Pos. OSD Timer Back
In the Language menu, there are:
English Frances Germany Spanish Traditional Chinese Simplified Chinese Japanese
In the Misc menu, there are:
Signal Source
Select VGA: Analogue VGA Input Select DVI: Digital DVI-D Input Select AV: Composite Video Input Select SV: S-Video Video Input
Reset Back
ADP-1XX8P User Manual
14
2.4 AD Board (VA-3600) OSD Functions
Cable Not Connected
2.) Getting into Burn-in Mode
Before setting into a burn-in mode, first disconnect the AC power cord. Then press (dont let them go) the buttons until the AC power cord is connected and the “RGB” appears on the top left corner
of your screen. Now it can be put into the burn-in mode for changing colors.
2.) Getting Out of Burn-in Mode
Before getting out of the burn-in mode, please first disconnect the AC power cord. Then press the button (If not workable, press the button and dont let them go) until the AC power cord is connected. Please dont let your fingers go until the AC power cord is connected again and the wording of RGB appears on the top left corner of your screen, and wait for 3 second. Under the non-signal entry situation, if is seen, exit is thus successfully made.
When the Burn-in Mode is Unable to Eradicate
4.) If the RGB is still on the top left corner of the screen, press to enter Miscellaneous and
choose Reset, and then Yes, and press . When the screen goes black, disconnect power and repeat the above steps.
5.) If the RGB is not found, disconnect the AC power cord first. Then press the buttons (dont let them go) until the AC power cord is connected, and wait for 2 to 3 seconds. When
RGB appears, repeat the above steps.
6.) Functions of OSD Keys
Auto Adjust Up/Left Down/Right Power
Menu/Entry Power Indicator
ADP-1XX8P User Manual
15
Chapter 3_____________________________
3.1 Introduction to Control Board
This chapter describes how to install drivers and other software that will allow your Touch Screen Controller Board to work with different operating systems. eGalaxy touch panel control board is a touch screen control board designed for USB interface and specific for touch screens. It is designed with USB interface features with multiple devices supporting function. It is designed for Projected Capacitive Touch Panel (PCAP) application; through glass touch sensing is ready for products that require a complete flat surface. It also can drive the touch panel to get two fingers touch function that based on the Windows 7 support.
Figure 3.1: Birds Eye View of control board
3.2 Installation of Control Board
Before installing the Windows 2000/XP driver software, you must have the Windows 2000/XP system installed and running on your computer.
ADP-1XX8P User Manual
16
Chapter 4_____________________________
4.1 Windows 2000/XP Driver Installation for eGalaxy Control
Board
Before installing the Windows 2000/XP driver software, you must have the Windows 2000/XP system installed and running on your computer. You must also have eGalaxy Interface controller board installed.
Follow the steps below to install eGalaxy Windows 2000/XP driver.
Step 1. Insert the CD-ROM. Go to Driver folder. Click Driver.
Step 2. There is eGalaxTouch, double click the folder.
ADP-1XX8P User Manual
17
Step 3. Click setup.
4.2 Configuring eGalaxTouch Windows 2000/XP Driver
After click setup, InstallShield Wizard screen appears click Next to continue.
ADP-1XX8P User Manual
18
Step 1. Tick Install RS232 interface driver. Then click Next.
Step 2. Select None. Then click Next to continue.
ADP-1XX8P User Manual
19
Step 3. Please make sure your touch monitor or touch controllers USB cable is plugged into the computer now. Click OK to continue the installation.
Step 4. If you want to use Multi-Monitor, check Support Multi-Monitor System. Then, click Next to continue the installation.
Step 5. Click Browse to create a new folder. Click Next to setup eGalaxTouch in the destination folder you want to install. Click Next to continue the installation.
ADP-1XX8P User Manual
20
Step 6. Under eGalaxTouch, select Accessories.
Step 7. Check Create a eGalaxTouch Utility shortcut on desktop. Click Next to continue.
ADP-1XX8P User Manual
21
Step 8. The installation files are extracted.
Step 9. eGalaxTouch driver has been installed. To do 4 point calibration, click Yes to continue.
ADP-1XX8P User Manual
22
Chapter 5_____________________________
5.1 Software Functions
General
In this window, you can see there is a USB Controller. Click OK to continue.
ADP-1XX8P User Manual
Monitor Mapping
to adjust touch panel
Add
to search for device
23
Setting Check Beep On Touch and Beep from System Beep, click OK to continue.
Beep
Beep On Touch: when you touch, it will beep. Beep On Release: when you release, it will beep. Beep From System Beep Beep From Sound Card
Linearization Style
9 points 25 points
Double Click Time
Shorter
Longer
Double Click Area
Smaller Bigger
ADP-1XX8P User Manual
24
Normal mode
Simulate the mouse mode
Check Enable Constant Touch, Enable Auto Right Click, Enable Touch, Enable Cursor
Stabilization. Click OK to continue.
Option
Function
Enable Constant Touch Enable Auto Right Click Enable Touch Enable Cursor Stabilization Constant Touch Area Auto Right Click Time
ADP-1XX8P User Manual
25
Tools
Click OK to continue the settings.
4 Points Calibration Do 4 points alignment to match display.
Clear and Calibrate Clear linearization parameter and do 4 points alignment.
Linearization Do 9 points linearization for better touchscreen linearity.
Draw Test Do draw test to verify the touch accuracy.
ADP-1XX8P User Manual
26
Display
In this window, it shows the mode of display. Select Full Screen, click OK to continue.
Enable Multiple Monitors.
Map to main display if system has only one display monitor
Full Screen
Lower Screen Left Screen Upper Screen Right Screen
ADP-1XX8P User Manual
27
Other
Other mode of display. Quarter1~4 and Customized area.
Active Area
Drag active area to enable Active Area Function.
ADP-1XX8P User Manual
28
Hardware Click OK.
Hardware Configuration Click OK to continue.
ADP-1XX8P User Manual
29
About
To display information about eGalaxTouch and its version.
ADP-1XX8P User Manual
Loading...