Aplex ADP-1154 User Manual
ADP-1154 Display Monitor
User Manual
Release Date Revision
Oct. 2007 V0.1
®2005 Aplex Technology, Inc. All Rights Reserved. Published in Taiwan
Aplex Technology, Inc.
9F-5, No. 2, Jian Pa Road, Chung Ho City, Taipei County, Taiwan
Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: aplex@aplex.com.tw URL: www.aplex.com.tw
ADP-1154 User Manual
1
Warning!___________________________________
This equipment generates, uses and can radiate radio frequency energy and if not installed and
used in accordance with the instructions manual. It may cause interference to radio communications.
It has been tested and found to comply with the limits for a Class A computing device pursuant to
FCC Rules, which are designed to provide reasonable protection against such interference when
operated in a commercial environment. Operation of this equipment in a residential area is likely
to cause interference in which case the user at his own expense will be required to take whatever
measures may be required to correct the interference.
Electric Shock Hazard – Do not operate the machine with its back cover removed. There are
dangerous high voltages inside.
Disclaimer
This information in this document is subject to change without notice. In no event shall Aplex Technology
Inc. be liable for damages of any kind, whether incidental or consequential, arising from either the use or
misuse of information in this document or in any related materials.
ADP-1154 User Manual
2
Table of Contents______________________
Warning!…………………………………………………………………………….……..….2
Disclaimer………………………………………………………………….…………………2
Chapter 1 Getting Started
1.1 Features…...……………………………………………………….…..…..…5
1.2 Specifications…………………………………………. ...……………...….5
1.3 Dimensions…………...………………………...………………………….…6
1.4 Brief Description......................................................................................7
1.5 Display Mode………...……………………………………………………….8
Chapter 2 OSD
2.1 Front Panel Controls……………………………………………….…..…….9
2.2 OSD Controls…………………..……………………………………………..9
2.3 Main Menu…..………..……………………………………………………..10
2.4 AD Board (TB-6020) OSD Functions…….………………………………13
Chapter 3 Control Board
3.1 Introduction to PenMount Control Board………………………………..14
3.2 Features…………………………………………………………………….15
3.3 Electrical Specifications…………………………………………………...15
3.4 Installation of Control Board……………………………………………...16
Chapter 4 Installation
4.1 Windows 2000/XP Driver Installation…………………………………….17
4.2 Configuring PenMount Windows 2000/XP Driver………………………21
4.3 Uninstall PenMount Windows 2000/XP Driver………………………….31
Chapter 5 Software
5.1 Software Functions………………………………………………………..32
5.2 Software Function Descriptions……………………………………….…33
ADP-1154 User Manual
3
Appendix A: Board Description & Specifications………………….40
Appendix B: Controller IC Specifications………………………………42
Figures
Figure 1.1: Dimensions of ADP-1154….……………………………………..6
Figure 1.2: Front View of ADP-1154………………………………………….7
Figure 3.1: Bird Eye’s View of Control Board………………………………14
Figure 3.2: Mechanical Drawing of Control Board…………………………14
Figure A: Panelmounting……………………………………………………43
Figure B: VESA 100 mounting………………………………………….….44
Appendix
Panelmounting…..…………………………………………………………….43
VESA 100 mounting…………………………………………………………..44
ADP-1154 User Manual
4
Chapter 1_____________________________
1.1 Features
● 15” TFT XGA LCD with luminance of 400 cd/m²
● Front panel NEMA 4/IP 65 rated
● Resistive touch screen (optional)
● Panel mount/VESA mount
● DVI, Video or S-Video input
● Supports wide-ranging resolutions from 640x480 to up to 1600x1200
with auto phase and auto position
1.2 Specifications
Display
● Display: 15” color active TFT flat panel display
● Maximum resolution: 1024 x 768 (native mode)
● Maximum colors: 16.2M
● Luminance: 400 cd/m²
● Viewing angle: 140°(H), 125°(V)
● Backlight life: CCFL 4 tubes 50,000 hrs
● OSD controls/indicators: automatic screen, setup (OSD), brightness,
contrast, horizontal/vertical position, image lock, color balance,
video information, power on and sync detection
● Touch screen: resistive antiglare
● OS compatibility: Win 95/98, XP, 2000, NT4.0, QNX, Linux
● Internal Power Adapter: Input: 100~240±10%V AC, full ranging
Output: 12V DC @5A
Mechanical
● Construction: steel chassis and aluminum front panel
● Mounting Options: panel mount/VESA mount
● OSD on the front side
● Dimensions: 409(W) x 309(H) x 64.7mm (D)
● Cutout Dimensions: 390(W) x 290mm (H)
● Weight: 5.32kg
ADP-1154 User Manual
5
Environmental
● Operating temperature: 0 to 50℃ (32 to 122℉)
● Storage temperature: -20 to 60℃ (-4 to 140℉)
● Relative humidity: 10 to 95% @40℃, non-condensing, without touch screen
● Vibration: 1G peak, 5~500Hz (at random)
● Shock: 15G peak acceleration (11 msec.duration)
● EMC: Meet CE, FCC Class A
Ordering Information
ADP-1154 15” industrial display monitor (aluminum bezel & front OSD)
ADP-1154T 15” industrial display monitor (aluminum bezel & front OSD) w/resistive touch screen
1.3 Dimensions
ADP-1154 User Manual
Figure 1.1: Dimensions of the ADP-1154
6
1.4 Brief Description of the ADP-1154
The ADP-1154 features an excellent viewing ability for monitoring and control applications. It is
available with resistive touch screen that is easy to use and maintain.
The front panel of the display monitor is sealed with gasket for NEMA 4/IP 65 rating when it is
panel-mounted in a NEMA rated cabinet or enclosure.
Figure 1.2: Front View of the ADP-1154
ADP-1154 User Manual
7
1.5 Display Mode
Display Mode Hori. Sync (KHz) Vert. Sync. (Hz)
31 60
VGA 640 x 480 38 72
38 75
35 56
SVGA 800 x 600 38 60
48 72
47 75
48 60
XGA 1024 x 768 56 70
60 75
SXGA
1152 x 864 68 75
64 60
1280 x 1024
80 75
ADP-1154 User Manual
8
Chapter 2_____________________________
2.1 Front Panel OSD Functions
Auto Adjust Up/Left Down/Right Power
Menu/Entry Power Indicator
Power switch: To turn ON or OFF the power
Shift the icon to the right side or shift it up
Shift the icon to the left side or shift it down
Menu: To enter OSD menu for related icon and item.
Auto Button: One-touch auto adjustment
1.) Getting into Burn-in Mode
Before setting into a burn-in mode, first disconnect the AC power cord. Then press (don’t let them go)
the
of your screen. Now it can be put into the burn-in mode for changing colors.
2.) Getting Out of Burn-in Mode
buttons until the AC power cord is connected and the “RGB” appears on the top left corner
Before getting out of the burn-in mode, please first disconnect the AC power cord. Then press the
button (If not workable, press the
connected. Please don’t let your fingers go until the AC power cord is connected again and the
wording of “RGB” appears on the top left corner of your screen, and wait for 3 seconds. Under the
non-signal entry situation, if is seen, exit is thus successfully made.
ADP-1154 User Manual
Cable Not Connected
button and don’t let them go) until the AC power cord is
9
2.2 OSD Controls
To make any adjustment, select the following:
1. Press
2. Select the icon that you wish to adjust with the ( / or +/-) key in the menu.
3. Press (Menu) and then choose the item with the ( / or +/-) key.
4. Press (Menu) and then adjust the quality with the ( / or +/-) key.
(Menu) to show the OSD menu or disable the OSD menu.
1.) If the “RGB” is still on the top left corner of the screen, press to enter “Miscellaneous” and
choose “Reset”, and then Yes, and press . When the screen goes black, disconnect power
and repeat the above steps.
2.) If the “RGB” is not found, disconnect the AC power cord first. Then press the buttons
(don’t let them go) until the AC power cord is connected, and wait for 2 to 3 seconds. When
“RGB” appears, repeat the above steps.
3.) Functions of OSD Keys
ADP-1154 User Manual
10
2.3 Main Menu
In the Main menu, there are the following items:
z Color
z Image Setting
z Position
z OSD Menu
z Language
z Misc
z Exit
For Color, check out the following:
z Contrast
z Brightness
z Color Adjust
z Color Temp
z Back
For Image setting, check out the following:
z Clock
z Phase
z Gamma
z Sharpness
z Back
ADP-1154 User Manual
11
In the Position, there are the following:
z H. Position
z V. Position
z Back
In the OSD menu, there are:
z OSD H. Pos.
z OSD V. Pos.
z OSD Timer
z Back
In the Language menu, there are:
z English
z Frances
z Germany
z Spanish
z Traditional Chinese
z Simplified Chinese
z Japanese
In the Misc menu, there are:
z Signal Source
ADP-1154 User Manual
Select VGA: Analogue VGA Input
Select DVI: Digital DVI-D Input
Select AV: Composite Video Input
Select SV: S-Video Video Input
z Reset
z Back
12
2.4 AD Board (TB-6020) OSD Functions
2.) Getting into Burn-in Mode
Before setting into a burn-in mode, first disconnect the AC power cord. Then press (don’t let them go)
the buttons until the AC power cord is connected and the “RGB” appears on the top left corner
of your screen. Now it can be put into the burn-in mode for changing colors.
2.) Getting Out of Burn-in Mode
Before getting out of the burn-in mode, please first disconnect the AC power cord. Then press the
button (If not workable, press the button and don’t let them go) until the AC power cord is
connected. Please don’t let your fingers go until the AC power cord is connected again and the
wording of “RGB” appears on the top left corner of your screen, and wait for 3 second. Under the
non-signal entry situation, if is seen, exit is thus successfully made.
When the Burn-in Mode is Unable to Eradicate…
4.) If the “RGB” is still on the top left corner of the screen, press to enter “Miscellaneous” and
choose “Reset”, and then Yes, and press . When the screen goes black, disconnect power and
repeat the above steps.
5.) If the “RGB” is not found, disconnect the AC power cord first. Then press the
(don’t let them go) until the AC power cord is connected, and wait for 2 to 3 seconds. When
“RGB” appears, repeat the above steps.
6.) Functions of OSD Keys
Cable Not Connected
buttons
Auto Adjust Up/Left Down/Right Power
Menu/Entry Power Indicator
ADP-1154 User Manual
13
Chapter 3_____________________________
3.1 Introduction to the PenMount 9036 Controller Board
The PenMount 9036 control board is configured for use with the RS-232 interface. It connects to the
touch screen, power supply and computer system’s RS-232 port, and supports 4-, 5- and 8-wire touch
screens. The control board has some advanced functions, such as PnP and non-PnP mode adjustable
baud rate, thus making easy for customers to select different touch screens without changing the
control board. The size of the board is 25 by 60mm, and it has two connectors and one dipswitch
on-board.
Figure 3.1: Bird’s Eye View of PenMount 9036
Figure 3.2: Mechanical Drawing of PenMount 9036
ADP-1154 User Manual
14
Loading...