API 4590, 4590R User Manual

SERIES
High Current Filter Inductors
Actual Size (Max.)
Physical Parameters
Inches Millimeters Length 0.900 Max. 22.86 Max. Diameter 0.455 Max. 11.55 Max. Lead Size
AWG #20 TCW 0.032 ± 0.002 0.813 ± 0.05
Lead Length 1.10 Min. 27.94 Min.
Operating Temperature
–55°C to +125°C –55°C to +85°C @ full rated current
Current Rating at 85°C Ambient 40°C Rise
Maximum Power Dissipation at 85°C 0.70 W
Dielectric Withstanding Voltage 2500 V RMS
Incremental Current The current which will decrease the
inductance by approximately 5%.
Inductance Measurement Inductance is measured @ 1 kHz with 1 VAC open circuit and 0 dc bias.
Inductance Tolerance Tolerance is specified by suffixing an alpha character to the part number as follows: J = 5%, K = 10%, and L = 15%. Units are normally supplied to the tolerance indicated in table.
High Saturation Bobbin allows for high inductance with low DCR.
High Resistivity Core offers very high parallel resistance, resulting in maximum coil performance.
4590 Marking DELEVAN; inductance; tolerance.
4590R Marking DELEVAN; 4590R; dash number with
tolerance letter.
Example: 4590-393K
DELEVAN 39 uH ±10%
Example: 4590R-393K
DELEVAN 4590R 393K
Packaging Bulk only
4590
4590R
D
A
S
H
N
U
N
MB
E
R
*
-392K
-472K
-562K
-682K
-822K
-103K
-123K
-153K
-183K
-223K
-273K
-333K
-393K
-473K
-563K
-683K
-823K
-104K
-124K
-154K
-184K
-224K
-274K
-334K
-394K
-474K
-564K
-684K
-824K
-105K
-125K
-155K
-185K
-225K
-275K
-335K
-395K
-475K
-565K
-685K
-825K
-106K
-126K
-156K
-186K
-226K
-276K
-336K
-396K
-476K
-566K
-686K
-826K
-107K
O
MIN
D
U
C
)
±1
0
MA
D
C
XIMU
R
ESIST
A
N
%
3.9
4.7
5.6
6.8
8.2
10.0
12.0
15.0
18.0
22.0
27.0
33.0
39.0
47.0
56.0
68.0
82.0 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 18000 22000 27000 33000 39000 47000 56000 68000 82000 100000
M (
O
H
C
E
SERIES 4590 FERRITE CORE
MS)
A
IN
(
µ
H
MA
XIMU
A
N
C
E
0.007
0.008
0.011
0.011
0.013
0.016
0.018
0.020
0.022
0.024
0.025
0.028
0.031
0.034
0.043
0.059
0.066
0.084
0.113
0.129
0.150
0.162
0.226
0.257
0.288
0.393
0.504
0.570
0.643
0.844
0.977
1.18
1.50
1.76
2.13
2.53
2.84
3.79
4.24
5.75
6.44
7.30
9.34
10.7
14.8
18.0
22.7
25.7
29.7
33.7
38.0
52.8
67.3
76.0
C
U
C
U
R
R
EN
M (
R
A
AT
MPS)
IN
G
9.75
9.11
7.77
7.60
7.15
6.44
6.07
5.76
5.49
5.26
5.15
4.87
4.63
4.45
3.93
3.355
3.175
2.815
2.43
2.27
2.105
2.025
1.715
1.61
1.52
1.30
1.15
1.08
1.015
0.89
0.825
0.75
0.665
0.615
0.56
0.51
0.48
0.415
0.395
0.34
0.32
0.30
0.265
0.25
0.21
0.19
0.17
0.16
0.15
0.14
0.13
0.11
0.10
0.09
Optional Tolerances: J = 5% L = 15%
*Complete part # must include series # PLUS the dash #
For surface finish information, refer to www.delevanfinishes.com
R
R
EN
INCREMENTAL
T DC (AMPS)
Power Inductors
8.2
7.5
6.9
6.3
5.7
5.2
4.7
4.3
3.9
3.5
3.2
2.9
2.7
2.5
2.3
2.1
1.9
1.7
1.6
1.4
1.3
1.2
1.1
0.95
0.88
0.80
0.74
0.67
0.61
0.56
0.51
0.46
0.42
0.38
0.34
0.31
0.29
0.26
0.24
0.22
0.20
0.18
0.17
0.15
0.14
0.12
0.11
0.10
0.09
0.09
0.08
0.07
0.07
0.06
270 Quaker Rd., East Aurora NY 14052 • Phone 716-652-3600 • Fax 716-652-4814 • E-mail: apisales@delevan.com • www.delevan.com
1/2009
Loading...