Apex SA13 Datasheet

SA13

USA BeO

∆

TE949311

PULSE WIDTH MODULATION AMPLIFIER

MICROTECHNOLOGY

HTTP://WWW.APEXMICROTECH.COM (800) 546-APEX [phone]

FEATURES

• HALF BRIDGE OUTPUT

• WIDE SUPPLY RANGE—16-100V

• 30A CONTINUOUS TO 60°C CASE

• 3 PROTECTION CIRCUITS

• ANALOG OR DIGITAL INPUTS

• SYNCHRONIZED OR EXTERNAL OSCILLATOR

• FLEXIBLE FREQUENCY CONTROL

APPLICATIONS

• MOTORS TO 4HP

• REACTIVE LOADS

• LOW FREQUENCY SONAR

• LARGE PIEZO ELEMENTS

• OFF-LINE DRIVERS

• C-D WELD CONTROLLER

DESCRIPTION

The SA13 is a half bridge pulse width modulation amplifier
that can supply 3000W to the load. Flexible frequency control
is provided. An internal 45kHz oscillator requires no external
components and can be used to synchronize multiple ampli­fiers. The oscillator output may be divided down and con­nected to the clock input to lower the switching frequency . The
clock input stage divides by two and determines the output
switching rate (normally 22.5 kHz). A shutdown input turns off
both output drivers. High side current sensing protects the
amplifier from shorts to ground. In addition, the half bridge
output MOSFETs are protected from thermal overloads by
directly sensing the temperature of the die. The 12-pin her­metic MO-127 power package occupies only 3 square inches
of board space.

BLOCK DIAGRAM AND TYPICAL APPLICATION
PROGRAMMABLE POWER SUPPLY

SA13

EXTERNAL CONNECTIONS

NC

CLK IN

CLK OUT

+PWM

–PWM/RAMP

SIG GND

1
2
3

TOP

TOP

VIEW

VIEW

4
5
6

SHDN

Case tied to pin 5. Allow no current in case. Bypassing of supplies
is required. Package is Apex MO-127 (STD). See Outline
Dimensions/Packages in Apex data book.

If +PWM < RAMP/–PWM then OUT = HIGH.
*See text.

12
11
10

9
8
7

NC

*

VCC

*

+VS

OUT
PWR GND

Vcc

10

+PWM

3

–PWM/RAMP

CONTROL

SIGNAL

3/7V

APEX MICROTECHNOLOGY CORPORATION • TELEPHONE [phone] • FAX [phone] • ORDERS [phone] • EMAIL [e-mail]

5V

4

470pF

56K

CLK OUT

2

CLK IN

1

5

SIG GND

÷2OSC

10V

P-P

CURRENT

LIMIT

PWM

OUTPUT

DRIVERS

SHUTDOWN

CONTROL

5V

9

+V

OUT

8

12

NC

NC

11

6

SHDN

7

PWR GND

S

LOAD

5K

.01µF

RSENSE

SA13

ABSOLUTE MAXIMUM RATINGS

SPECIFICATIONS

ABSOLUTE MAXIMUM RATINGS

SUPPLY VOLTAGE, +V
SUPPLY VOLTAGE, V
POWER DISSIPATION, internal 150W
TEMPERATURE, pin solder - 10s 300°C
TEMPERATURE, junction

S

CC

2

100V
16V

150°C
TEMPERATURE, storage –65 to +150°C
OPERATING TEMPERATURE RANGE, case –55 to +125°C
INPUT VOLTAGE, +PWM 0 to +11V
INPUT VOLTAGE, –PWM 0 to +11V
INPUT VOLTAGE, I

LIM

0 to +10V

SPECIFICATIONS

PARAMETER TEST CONDITIONS
CLOCK (CLK)

CLK OUT, high level
CLK OUT, low level
FREQUENCY 44 45 46 kHz

4

4

I

≤ 1mA 4.8 5.3 V

OUT

I

≤ 1mA 0 .4 V

OUT

RAMP, center voltage 5V
RAMP, P-P voltage 4V
CLK IN, low level
CLK IN, high level

4

4

OUTPUT

R

ON

EFFICIENCY, 10A output VS = 100V 97 %
SWITCHING FREQUENCY OSC in ÷ 2 22.05 22.5 22.95 kHz
CURRENT, continuous
CURRENT, peak

4

4

Each output driver .08 Ω

60°C case 30 A

POWER SUPPLY

VOLTAGE, V
VOLTAGE, V
CURRENT, V
CURRENT, V
CURRENT, V

I

/SHUTDOWN

LIM

S
CC

CC

shutdown 50 mA

CC,
S

Full temperature range 16
Full temperature range 14 15 16 V
I

= 0 80 mA

OUT

No Load 50 mA

TRIP POINT 90 110 mV
INPUT CURRENT 100 nA

THERMAL

3

RESISTANCE, junction to case Full temperature range, for each die .83 °C/W
RESISTANCE, junction to air Full temperature range 12 °C/W
TEMPERATURE RANGE, case Meets full range specifications –25 +85 °C

2

MIN TYP MAX UNITS

0.9V

3.7 5.4 V

40 A

5

60 100 V

NOTES: 1. Each of the two output transistors can dissipate 150W.

2. Unless otherwise noted: TC = 25°C, VS, VCC at typical specification.

3. Long term operation at the maximum junction temperature will result in reduced product life. Derate internal power
dissipation to achieve high MTTF. For guidance, refer to the heatsink data sheet.

4. Guaranteed but not tested.

5. If 100% duty cycle is not required V

CAUTION

The SA13 is constructed from MOSFET transistors. ESD handling procedures must be observed.

S(MIN)

= 0V.

The internal substrate contains beryllia (BeO). Do not break the seal. If accidentally broken, do not crush,
machine, or subject to temperatures in excess of 850°C to avoid generating toxic fumes.

APEX MICROTECHNOLOGY CORPORATION • 5980 NORTH SHANNON ROAD • TUCSON, ARIZONA 85741 • USA • APPLICATIONS HOTLINE: [phone]