Apex PA16A, PA16 Datasheet

MICROTECHNOLOGY

–IN +IN

OUT

+V

–R

CL

+R

CL

S

–V

S

1 2 3 4 5 6 7 8 9 10 11 12

HTTP://WWW.APEXMICROTECH.COM (800) 546-APEX [phone]

FEATURES

• HIGH POWER BANDWIDTH — 350kHz

• HIGH SLEW RATE — 20V/µs

• FAST SETTLING TIME — 600ns

• LOW CROSSOVER DISTORTION — Class A/B

• LOW INTERNAL LOSSES — 1.2V at 2A

• HIGH OUTPUT CURRENT — ±5A PEAK

• LOW INPUT BIAS CURRENT — FET Input

• ISOLATED CASE — 300 VDC

APPLICATIONS

• MOTOR, VALVE AND ACTUATOR CONTROL

• MAGNETIC DEFLECTION CIRCUITS UP TO 5A

• POWER TRANSDUCERS UP TO 350 kHz

• AUDIO AMPLIFIERS UP TO 44W RMS

POWER OPERATIONAL AMPLIFIERS

PA16 • PA16A

TYPICAL APPLICATION

DESCRIPTION

The PA16 and PA16A are wideband, high output current
operational amplifiers designed to drive resistive, inductive
and capacitive loads. Their complementary “collector output”
stage can swing close to the supply rails and is protected
against inductive kickback. For optimum linearity, the output
stage is biased for class A/B operation. The safe operating
area (SOA) can be observed for all operating conditions by
selection of user programmable, current limiting resistors
(down to 10mA). Both amplifiers are internally compensated
but are not recommended for use as unity gain followers. For
continuous operation under load, mounting on a heatsink of
proper rating is recommended.

These hybrid integrated circuits utilize thick film (cermet)
resistors, ceramic capacitors and semiconductor chips to
maximize reliability, minimize size and give top performance.
Ultrasonically bonded aluminum wires provide reliable inter­connections at all operating temperatures.

EQUIVALENT SCHEMATIC

4

R1

R2 R3

R4

2

A1

1

R8

R9 R10

R11

6

R5

Q2

Q7

R12

Q1

R6

Q4

R15

Q5

R13

Q8

R7

Q3

Q6

R14

D1

D2

10
12

100K

+12

R

PA16

.27

R
.27

CL+

CL–

Ω

3.2

Ω

16W

Ω

.47µF

16K

1K

IN

.001µF

.47µF

LOW INTERNAL LOSS MAXIMIZES EFFICIENCY

16K

–12

Vehicular Sound System Power Stage

When system voltages are low and power is at a premium,
the PA16 is a natural choice. The circuit above utilizes not only
the feature of low internal loss of the PA16, but also its very low
distortion level to implement a crystal clear audio amplifier
suitable even for airborne applications. This circuit uses AC
coupling of both the input signal and the gain circuit to render
DC voltage across the speaker insignificant. The resistor and
capacitor across the inputs form a stability enhancement
network. The 0.27 ohm current limit resistors provide protec­tion in the event of an output short circuit.

EXTERNAL CONNECTIONS Package: SIP03

8

APEX MICROTECHNOLOGY CORPORATION • TELEPHONE [phone] • FAX [phone] • ORDERS [phone] • EMAIL [e-mail]

PA16 • PA16A

ABSOLUTE MAXIMUM RATINGS

SPECIFICATIONS

ABSOLUTE MAXIMUM RATINGS

SUPPLY VOLTAGE, +VS to –V
OUTPUT CURRENT, within SOA 5A
POWER DISSIPATION, internal

S

1

38V

62.5W
INPUT VOLTAGE, differential ±VS –5V
INPUT VOLTAGE, common mode ±VS –2V
TEMPERATURE, pin solder - 10s 300°C
TEMPERATURE, junction

1

150°C
TEMPERATURE RANGE, storage –65 to +150°C
OPERATING TEMPERATURE RANGE, case –55 to +125°C

SPECIFICATIONS

PARAMETER TEST CONDITIONS

PA16

2, 6

MIN TYP MAX MIN TYP MAX UNITS

PA16A

INPUT

OFFSET VOLTAGE, initial T
OFFSET VOLTAGE, vs. temperature Full temperature range ±10 ±50 * ±25 µV/°C
OFFSET VOLTAGE, vs. supply T
OFFSET VOLTAGE, vs. power TC = 25°C ±6*µV/W

= 25°C ±5 ±10 ±1 ±3mV

C

= 25°C ±10 * µV/V

C

BIAS CURRENT, initial TC = 25°C 50 200 25 100 pA
BIAS CURRENT, vs. temperature TC = 85°C 200 * pA/°C
BIAS CURRENT, vs. supply TC = 25°C .01 * pA/V
OFFSET CURRENT, initial TC = 25°C 25 100 15 50 pA
OFFSET CURRENT, vs. temperature TC = 85°C 100 * pA/°C
INPUT IMPEDANCE, DC TC = 25°C 1000 * GΩ
INPUT CAPACITANCE TC = 25°C3*pF
COMMON MODE VOLT. RANGE5, Pos. Full temperature range +VS –6+VS –3** V
COMMON MODE VOLT. RANGE5, Neg. Full temperature range –VS +6 –VS +5 * * V
COMMON MODE REJECTION, DC Full temperature range 70 100 * * dB

GAIN

OPEN LOOP GAIN at 10Hz TC = 25°C, 1kΩ load 103 * dB
OPEN LOOP GAIN at 10Hz Full temp. range, 10kΩ load 86 100 * * dB
GAIN BANDWIDTH PRODUCT at 1MHz TC = 25°C, 10Ω load 4.5 * MHz
POWER BANDWIDTH TC = 25°C, 10Ω load 350 * kHz
PHASE MARGIN Full temp. range, 10Ω load 30 * °

OUTPUT

VOLTAGE SWING
VOLTAGE SWING

3
3

TC = 25°C, IO = 5A, R
Full temp. range, IO = 2A ±VS –2 ±VS –1.2 ±VS –1.2 * V

= .08Ω±VS –4 ±VS –3 ±VS –3* V

CL

CURRENT, peak TC = 25°C5*A
SETTLING TIME to .1% TC = 25°C, 2V step .6 * µs
SLEW RATE TC = 25°C1320**V/µs
CAPACITIVE LOAD Full temp. range, AV > 10 SOA *
HARMONIC DISTORTION PO = 5W, F = 1kHz, RL = 4Ω .028 * %
SMALL SIGNAL rise/fall time RL = 10Ω, AV = 1 100 * ns
SMALL SIGNAL overshoot RL = 10Ω, AV = 1 10 * %

POWER SUPPLY

VOLTAGE Full temperature range ±7 ±15 ±19 * * * V
CURRENT, quiescent TC = 25°C2740**mA

THERMAL

RESISTANCE, AC junction to case

4

F > 60Hz 1.4 1.6 * * °C/W
RESISTANCE, DC junction to case F < 60Hz 1.8 2.0 * * °C/W
RESISTANCE, junction to air 30 * °C/W
TEMPERATURE RANGE, case Meets full range specifications –25 +85 * * °C

NOTES: * The specification of PA16A is identical to the specification for PA16 in applicable column to the left.

1. Long term operation at the maximum junction temperature will result in reduced product life. Derate internal power dissipation
to achieve high MTTF.

2. The power supply voltage for all specifications is the TYP rating unless otherwise noted as a test condition.

3. +VS and –VS denote the positive and negative supply rail respectively. Total VS is measured from +VS to –VS.

4. Rating applies if the output current alternates between both output transistors at a rate faster than 60Hz.

5. Exceeding CMV range can cause the output to latch.

6. Full temperature specifications are guaranteed but not 100% tested.

CAUTION

The exposed substrate contains beryllia (BeO). Do not crush, machine, or subject to temperatures in excess of 850°C to
avoid generating toxic fumes.

APEX MICROTECHNOLOGY CORPORATION • 5980 NORTH SHANNON ROAD • TUCSON, ARIZONA 85741 • USA • APPLICATIONS HOTLINE: [phone]