Aperio K100-622H-PA-B2 Installation Instructions

Download

Page 1

K100-622 Aperio Series

Wireless Cabinet Lock

Package Contents

Recommended Tools

Optional Addit ional Tools:

Drill, Drill bits: 1/16”, 3/16”, 1/2”

Flathead drivers 3/32”, 3/16”

Wireless Frequency: 2.4 GHz, IEEE 802.15.4, using AES 128-bit encryption

Product Specifications

For technical support please call 1-800-626-7590

QR codes can be scanned

K100-622

QR Codes

Strike Plate

Shaft Extension

2-56 x 1-1/4”

Energizer L91 Ultimate

Double door bracket

Lock Body

8-32 x 1 1/4”

8-32 x 2 1/2”

8-32 x 2 3/4”

6-32 x 5/16”

6 x 1/2”

2-56 x 7/16”

Key Override

Key Override Paddle

Template

Screws

Reader

8-32 x 5/16”

Hub Bracket

Wireless Hub

Installation Instructions

NOTE: The wireless hub and hub brack et a r e included with the K100-622H model.

HES, Inc. Phoenix, A Z

1.800.626.7590

www.hesinnovations.com

Breakaway

Lithium Batteries

Cam

Approved iCLASS or Prox ID credential.

Hub Power Requirement: 8–24 Volts Dir ect C urrent (V DC ), 25 0 millia mp s (mA) Lock Battery Type: Lithium AA Cell, 1.5 Volts (V) (Energizer L91 Ultim ate Lithium ) Battery Life: 50,000 cycles

Operating Temperatur e: 32 °F to 122 °F (0 °C to 50 °C) FCC Part 15 Compliant, IC Compliant

Credentials Supported: (-PA) Low Frequency model: HID PROX, EM PROX

(-SE) High Frequency model: iCLASS, iCLASS SEOS , iCLASS SE, ISO14443B UID Mifare, Mifare Plus, Desfire SE, Desfire EV1, NFC

3080076.004, Rev. B 1

Phillips drivers P 0, P2

Pencil, Wire Stripper, Level, Square, Pliers

Gang box to mount hub

Cam Lock for Key Override

Tips and Videos

with a smart phone app

Page 2

System Overview

access control to a c a b inet or drawer without the complexity and

Testing the Lock

Connecting the Hub Mounting the Lock

Locating and Mounting the Hub (K100-622H only)

The K100-622 series wireless cabinet lock provides expense of running wires to the cabinet or drawer. The K100-622 series lock connects to an access control through a communication hub (included with the K100-622H). The communication hub connects to the access control system with Wiega nd wiring typical of a Wiegand Reader.

When a credential card is presen ted t o the reader on the lock the reques t for access is sent wirelessly to t he communication hub. The communica tion hub then communicates through Wiegand wiring to the access control system where the decision is made to grant or deny access.

Installation Process

(K100-622H only)

3080076.004, Rev. B 2

Page 3

Choosing the hub location

Mounting the Hub

NOTE: The following applies primarily

to the K100-622H Model with included hub.

It is recommended that the hub be mounted near th e top of a wall, on the ceiling or above th e c e iling to reduce potential for interference, and be facin g toward the lock for be s t p erformance.

For a stable and relia ble radio link, it is recommended that the hub is located within fifty ( 50 ) feet of the lock. A maximum of two interior walls between the hub and lock is recommended

Recommended locations:

A: Wall Mount B: Ceiling Mount C: Wall Mount, Adja c ent Room

NOTE: The hub is not rated for use in

plenum air spaces.

Mounting the Hub

NOTE: The following applies primarily to th e K 1 00-622H Model with included hub.

The included adapter plate c a n be used to mount the hub on a single or double gang box.

3080076.004, Rev. B 3

Page 4

Connecting the Hub

If the RED LED sign a l is not connected, the lock will

1. CONNECT the Wiegand D1, D0, red and green LED signals.

3. CONNECT Latchbolt Position, Low

Form C relays.

2. CONNECT 8–24 VDC and ground (250 mA).

Connecting the hub

NOTE: The following applies primarily to th e K 1 00 -622H Model with included hub.

The Aperio (250mA). The hub includes th r ee Form C relays tha t can be used to transmit latch bolt position s ta tus, low battery signal, and a tamper signal. The hub connects to the cabinet lock wirelessly.

NOTE 1: The Green LED input is used to grant access to the c a b inet lock. If the G r e en LED signal is not av a ila b le

NOTE 2: The Red LED input is used to indicate a c c es s denied.

Hub connects to the Access Control system via Wiegand wiring. The hub requires 8–24 VDC power

Battery, and Tamper Switch Detection

to indicate approved access, the a p pr oval input can be activ ated by a relay with “NO” attached to Green LED and “C” to GND.

flash RED three times when a non-approved card is presented indicating loss of connection to the hub rather than access denied. Any other codes may be reference on the LED r eference card.

3080076.004, Rev. B 4

Page 5

Testing the Lock with the Access Control System

1. REMOVE the battery cover from the

2. PASS the wire and shaft fro m the

3. CONNECT the wire (the wire is

4. INSTALL the batteries and ENSURE

5. PRESENT a

6. IF a green LED, indicating

8. REMOVE the batteries, UNPLUG

Testing the lock

NOTE: With the hub connected to power and the access control sys tem , the lock is tested w ith a known good

credential to confirm it will open as desired when ins talled.

3080076.004, Rev. B 5

lock body.

keyed) from the reader to the socket in the lock battery compartment.

credential known to the access control system.

access is granted, is lit; THEN TWIST the knob to retract the latch.

7. REFER to the LED reference card for any other c0des.

reader through the lock body.

correct orientation; the lock will self test and beep once.

the cable carefully, and SEPARATE the lock and reader to prepare for installation.

Page 6

***CAUTION***

Latch centerline notch

Mounting the Lock

MAC identification

The Installer mus t e nsure the lock can be opened before closing the cabinet at the end of these installation instructions.

Mounting the Lock

NOTE: The K100-622 reader and lock body c a n be

oriented in several ways to accommod a te various cabinets and drawers.

1. ESTABLISH the horizontal centerline of the latch.

1a. HOLD the lock body to the ins ide of the door and POSITION it generally where

you would like it to mount.

1b. LOCATE the lock centerline notch on the latch and MARK this point on the inside

of the cabinet door using a pencil.

1c. DRAW the horizontal latch centerline from this m ark on the inside of the cabinet

door and TRANSFER it to the outside of the cabinet door.

1d. TRANSFER this centerline to the inside of the cabinet or the second door on a

double-door cabinet.

1e. RECORD the M AC id entification nu m b er for transfer to Aperio

number on back side

software.

3080076.004, Rev. B 6

Page 7

2. TRANSFER the location of the inside wall of the cabinet to the door.

Cabinet/door front view

Door edge 2a

3b, 3c, 3d

2a. MEASURE the horizontal distance between the inside edge of the cabinet a nd the door edge.

NOTE: The drawn line depic ts the location of the strike mounting s urface.

2b. DRAW a line on the outside surface of the door, using the same distance away from the door edge.

3. PLACE and USE the Lock/Reader Template.

NOTE: Orientation will be r eversed for a right hand door.

3a. CUT through line to s ep a rate the Strike Plate Template.

3b. PEEL OFF the protective layer of the Lock Template, ALIGN it to both the latch

centerline and th e line depicting the ins id e wall of cabinet, and PRESS to secure.

NOTE: Two of the holes in the f ollowing step are 3/16” diameter a nd two are

1/2” diameter. The two pilot holes ar e 1/16”.

3c. DRILL four holes a nd two pilot holes through the cabinet, as shown

in the figure below.

3d. DRILL only on e 3/16” hole depending on the desired

Antenna/Reader orientation.

3e. IF the optional K ey Override will be installed,

THEN GO TO Step 5.

3f. REMOVE the lock template from the door.

3080076.004, Rev. B 7

Page 8

4. INSTALL the Shaft Extension.

Shaft Extension

2-56 X 1-¼” screw (provided)

Table 1

6b. INSTALL the optional Cam Lock with

figure.

4a. IF the cabinet door thickn ess is greater than ½ ”,

THEN INSTALL the Shaft Extension to the A ntenna/Reader to ens ure proper engagem ent into the lock.

4b. INSTALL the Shaft Extension to the shaft as shown

in the figure and fi r mly TIGHTEN the screw.

Door Thickness

1/16” – ½” No > ½” – 1 ½” Yes

Extension

Shaft Used?

5. IF a Cam Lock Key Override will be used, AND the orientation allows for installation, THEN INSTALL the Key Override Paddle.

5a. INSERT the Paddle’s arm into the opening shown, and ALIGN the r ails of the paddle to the one s on the

lock.

5b. SLIDE the paddle

gently until it stop s .

6. PREPARE the Key Override Door.

NOTE: The Cam Lock is optional and mus t

be obtained by others.

6a. IF a Key Override is used,

THEN USE template to mark and dr ill a hole for a 3/4” Cam Lock in the door.

the cabinet lock as shown in the

3080076.004, Rev. B 8

Page 9

7. INSTALL the Antenna/Reader.

Reader mounting screw.

Table 2

Cable is threaded

Used only for door s less

***CAUTION***

Pinching the wires may prevent the Re a der and Lock from properl y functioning.

7a. PLACE and HOLD the antenna/reader to the outside

of cabinet, routing the wire through the 1/2” offset hole, and ENS URE the knob is in the locked pos ition in the vertical.

NOTE: Using the Table 2 below will help determine the

length of the top mount screw needed, based on the thicknes s of the cabinet door.

7b. INSTALL the top mount screw to attach

the antenna/reader to the ou ts ide ca s e.

8. INSTALL the lock.

8a. REMOVE the battery cover from lock.

8b. PLACE the lock on the inside of the door, threadi ng the cable through the lock.

8b. ATTACH the lock to the anten na/reader using two 8-32 lock mount screws

(see Table 2 for length), and TIGHTEN the screws.

8c. INSTALL the tw o #6 self-threading screws and TIGHTEN.

NOTE: The third #6 self-threading s c rew is important to

achieve maximum holding force for doors greater than 5/8” thick.

8d. INSTALL the third # 6 self-threading screw only if the door

is more than 5/8” thick, using the lock as a guide, and TIGHTEN.

through the hole in the lock.

3080076.004, Rev. B 9

than 5/8” thick.

Page 10

9. Electrically CONNECT the antenna/reader wire to the lock body.

10a

10b

Connector cable tucked in

NOTE: The antenna/r eader wire connector is keyed to only fit one w ay.

9a. ENSURE correct orientation of the connector w hile inserting it.

9b. TUCK excess cable into lock body as shown.

10. INSTALL the Batteries.

NOTE: New batteries should always be used and inserted in the

correct polarity position.

10a. INSTALL the battery and battery cover.

10b. INSTALL and TIGHTEN the screws.

11. PLACE the single-door Strike Plate Template.

11a. PEEL OFF the protective layer of th e Strike Plate Template

11b. DRILL two pilot holes a s shown on template.

11c. REMOVE the template.

3080076.004, Rev. B 10

and ALIGN it to both the latch centerline and the edge of cabinet.

Page 11

***CAUTION***

door.

13a 13b and 13c

12a–c

12d

The Installer mus t e nsure the lock can be opened before closing t he cabinet.

12. INSTALL the single-door strike plate.

12a. PLACE the strike plate over the pilot holes, and INSERT and TIGHTEN the two screws in the slotted h ole s .

12b. CLOSE the door to verify in stallation, and ADJUST the strike plate if necessary.

12d. INSERT and TIGHTEN the lock down screw on the strike plate.

OPTIONAL DOUBLE-DOOR INSTALLATION

13. INSTALL the Double-Door Strike Plate Mounting Bracket

NOTE

13a. PLACE the bracket on door, making sure it aligns with the mark made in Step 2c and the edge of the

13b. MARK the door.

13c. REMOVE the bracket and DRILL pilot holes at the two marks.

13d. INSTALL the bracket using the mounting sc r ews provided.

: The double-door bracket requires that one door can be secu r ed.

14. INSTALL the double-door strike plate.

14a. PLACE the strike plate over the holes on the bracket.

14b. INSERT and TIGHTEN the three 6-32 X 5/16”screws

provided.

3080076.004, Rev. B 11

Page 12

WARNING

For Technical Support please call 1-800-626-7590

FCC Statement

This equipment has been tested and found to comply with the limits for a class B digital dev ic e , pur s uant to part 15 of the FCC Rules. These limits are designed to provide reaso nable protectio n against harmful inter ference in a resid ential installatio n. This equip ment generates, uses, and can radiate radio freque ncy energy and if no t installe d and used in accor dance with the instr uctions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip ment does cause harmful interfer ence to radio or television re ception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter fe renc e by one or more of the foll owing measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equip me nt and rec e iver.

3. Connect the equipment into an outlet on a circuit d iff er e nt fro m that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV techni c ian for hel p . Operation with non-approved equip ment is likely to result in interference to radio and TV reception. The user is cautioned that

changes and modificatio ns made to the equipment w ithout the approval of manufacturer could void the user’s authority to op erate this equipment.

IC Statement

This device complies with Industry Canada license-exempt RSS standards(s). Operation is subject to the following two conditions: (1) This device may not cause interfer e nce, and (2) This device must accept any interfere nc e , inc lud ing inte r ference that may cause undesired operation.

Conformité aux normes F CC

Cet équipement a été testé et trouvé conforme aux limites pour un dispositif numérique de classe B , conformément à la Partie 15 des règlements de la FCC. Ces limites sont conçues pour fournir une p rotection raisonnable co ntre les interférences nuisible s dans une installation résid entielle. Cet équipeme nt génère, utilise et pe ut émettre des fréquences r adio et, s'il n'est pas installé e t utilisé conformément ment aux instructions du fabricant, peut causer des interferences nuisibles aux communications radio. Rien ne garantit cependant que l'interférence ne se produira pas dans une installation particulière. Si cet équipement provoque des interférences nuisibles à la réception radio ou de télévis ion, qui peut être déterminé en comp arant et en l'éteignant, l'utilisate ur est encouragé à essayer de corriger les interfére nc e p ar une ou plusieur s des mesur es sui v antes:

1. Réorienter ou déplacer l'antenne de réception.

2. Augmenter la distance entre l'équipe m e nt et le récep teur .

3. Branchez l'appareil dans une prise sur un c irc uit différent de celui auquel le récepteur est connecté.

4. Consultez votre revendeur ou un technicien radio / TV pour assistance.Avertissement Les changements ou modififications à cet appareil sans expressément approuvée par la partie responsable de conformité pourraient

annuler l'autorité de l'utilisate ur de fair e fonc tionner cet équipement.

Conformité aux normes IC

Cet appareil est confrome avec Industrie Canada exe mpt de licens e RSS standard (s). Son fonctionnement est souimes aux deux conditions suivantes:

(1) cet appareil ne peut causer d’interférences, et (2) cet appareil doit accepter toute interfere nc e , y compr is des inter f ér e nc es qui peuv e nt provo quer un fonctionnement indésirable

du périphérique.

3080076.004, Rev. B 12