Aperio K100-622H-IPS-BP, DEMO-K100-622-IPS-BL, DEMO-K100-622-IPS-BP Installation Instructions

Page 1 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Products Specifications

Wireless Frequency: 2.4GHz, IEEE 802.15.4, using AES 128-bit encryption
Lock Battery Type: AA Lithium, 1.5 Volts (V)
Battery Life: 50,000 cycles*

*All battery life claims are approximate and based on a set configuration profile. Battery performance is based on pre-defined system settings such
as battery chemistry and battery model used, credential presentation settings (LED/buzzer), UHF polling period, UHF status intervals, and
operations per day. Actual battery performance will vary and depends on the factors above.

Operating Temperature: 32 to 122 F (0 to 50 C)
HID® multiCLASS SE® technology Credentials Supported:

 High Frequency (13.56 MHz):

 HID iCLASS®
 HID iCLASS SE® (SIO-enabled)
 HID iCLASS® Seos™
 HID MIFARE® SE
 HID DESfire® EV1 SE
 MIFARE CLASSIC
 DESfire® EV1

 Low Frequency (125 kHz):

 HID Prox®, AWID, EM4102, ioProx

 NFC-enabled Mobile Phones

AA Lithium Batteries
required. Use of other
types of batteries, such as
alkaline, will significantly
decrease battery life.

2x

HES K100 Aperio Series
Wireless Cabinet Lock

Installation and Operating Instructions

Page 2 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Recommended Tools

Flathead Drivers — 3/32”, 3/16”
Drill, Drill Bits — 1/16”, 3/16”, 1/2”
Phillips Drivers — P0, P2
Pencil, Wire Stripper, Level, Square, Ruler, Punch, Scissors

Hardware Specifications

Table 1 – Shaft Length

Table 2 – Mounting Screw Length for Various Door Thickness

Door

Thickness

Reader

Mounting

Cut to

approx.

screw

length

Lock

Mounting

Cut to

Approx.

Screw

Length

1/16”

Coupling Nut

and 3” Rod

10/16”

8-32 x 1-3/4”

Break Away

1-1/16”

1/4"

Coupling Nut

and 3” Rod

13/16”

8-32 x 1-3/4”

Break Away

1-1/4”

1/2”

Coupling Nut

and 3” Rod

1-1/16”

8-32 x 1-3/4”

Break Away

1-7/16”

3/4”

Coupling Nut

and 3” Rod

1-5/16”

8-32 x 1-3/4”

Break Away

No Cut

1”

Coupling Nut

and 3” Rod

1-9/16”

8-32 x 2-1/2”

2”

1-1/4”

Coupling Nut

and 3” Rod

1-13/16”

8-32 x 2-1/2”

No Cut

1-1/2”

Coupling Nut

and 3” Rod

2-1/16”

8-32 x 2-3/4”

No Cut

For Technical Support Please call 1-800-810-WIRE

Door Thickness

Shaft Used

1/16” – 1/2”

L1

>1/2” – 1½”

L2

>1½” – 2¼”

L3

Page 3 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Package Contents

6 X 1/2"

6x

(D)

6-32 X 5/16”

3x

(C)

8-32 X 5/16”

(B)

2-56 X 7/16”

2x

(A)

Reader

Lock Body

Strike Plate

Installation

Template

Mechanical Key Override

Hardware

8-32 X 2-1/2”

2x

(G)

8-32 X 2-3/4”

2x

(E)

8-32 X 1-3/4”

2x
(F)

Lithium Batteries

2x

Double Door

Bracket

8-32 X 3” Rod

(H)

8-32 Nut

(J)

Threadlock

Page 4 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Lock Orientation Options

Prepping the Cabinet/Drawer Face

1. Separate Strike Plate Template.

2. Establish centerline (for double door
cabinet prep go to page 6).

Orientation A

Orientation B

Orientation C

Page 5 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

3. Measure cabinet wall thickness and mark
offset line on face of cabinet/drawer. The
offset line should match with the interior
edge of the cabinet wall.

4. Continue centerline to face of
cabinet/drawer

5. Align template to offset line and
centerline. Remove backing and apply
template onto cabinet/drawer face.

6. Use punch to mark drilling
locations then drill mounting holes. If
using mechanical key override, drill
key override hole as well.

Center

line

Offset Line

Page 6 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Prepping the Cabinet/Drawer Face (Double Door)

3. Align offset line on template to the edge of the stationary door and align center
line with the established center line above. Remove backing and apply template to
cabinet face. Continue with Step 6 in previous section.

1. Establish center line on inside
of stationary door.

2. Continue center line onto
outside face of cabinet.

Page 7 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Reader Installation

1. Align reader with mounting holes and pull
cable through as shown. Trim Threaded rod
to length as outlined in table 2.

2. Add Threadlock to threaded rod.
Secure Reader to cabinet/drawer using
the cut threaded rod and coupling nut.
DO NOT overtighten.

Mechanical Override (Optional)

1. Slide Override into slot as shown.

2. Ensure that override retracts latch
bolt before installation. Override
should rest loosely until lock body and
battery cover are installed.

Page 8 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Lock Body Installation

1. Insert reader cable through hole
in back of lock body.

2. Align lock body to mounting holes
andsecure to cabinet/drawer face using
2x screw F and 2x screw D. If thick
cabinet/drawer then use 2x screw E or
2x screw G instead of 2x screw F. DO
NOT over tighten.

3. Plug cable into slot on lock body.

4. Tuck excess cable into lock body
cavity as shown.

5. Any excess cable should be inserted
into the cavity as shown below.

6. For cabinet/drawer face thicker
than1/2”, add a third screw D as
shown.

Page 9 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Installing the Batteries

1. Install AA lithium batteries in appropriate
position.

2. Install cover and secure using 2x
screw A.

Mechanical Key Override (Optional)

Mechanical key override cam lock sold
separately.

1. Insert cam lock through the outside
of the cabinet/drawer face and secure
with locking nut. Insert the end of Cam
into the mechanical override and secure
with nut as shown.

Important Note – Reader MUST be programmed before installing the strike plate. If the cabinet

is closed before the reader is programmed and after the strike plate is installed, you will be locked out of
the cabinet.

Page 10 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Strike Plate Installation

1. Align strike plate template to centerline
and edge of cabinet. Drill mounting holes.

2. Secure strike plate to inside cabinet
wall using 2x screw D, but do not fully
tighten. Adjust strike plate so the edge
is flush with the cabinet wall edge then
tighten.

3. After the strike plate is in the desired position, fasten screw D into strike plate as
shown below.

Page 11 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Double Door Strike Installation

1. Align Double door bracket with mounting holes from the strike plate template.
Secure double door bracket using 3x screw D.

2. Secure strike plate to double door bracket using 3x screw D as shown below.

Page 12 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

LED Codes

Page 13 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Aperio Hub

Technical Data – AH20

Approvals

CE, ETL, FCC, IC, C-Tick

Safety and emissions

FCC 47CFR Part 15 subpart
B and subpart C; IC RSS-210
EN ETSI 301 489-17 v2.1.1;
ENETSI 300 328 v1.7.1;
EN 60950-1 ed.2 2007

Dimensions

82x82x37

Power Supply

8-24 VDC

Current

250 mA minimum

Internal Antenna

2cross polarized dipoles

External Antenna
(Part No. EXT-10-ANT)

One reverse polarity SMA
external antenna connector.
Optional antenna type dipole with max
antenna gain of 3.9dBi

Radio Standard

IEEE 802.15.4(2.4GHz) –
15 channels (11-25)

Encryption (Radio
Communications)

AES 128 bits
Wireless Operating Range

Up to 50 ft

Receiver Sensitivity

100dBm 20%PER

Wireless Transmit Power

10 dBm/MHz

Class of Protection

IP 20

Operating temperature range

5°C to 35°C

Humidity

< 95% non-condensing

Status

LED (red/green/orange)

Page 14 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Connecting the Hub

The following applies only to Aperio factory paired kits with AH20 Hubs.

Note: The Green LED input is used to grant access to the cabinet lock. If the Green LED

signal is not available to indicate approved access, the approval input can be
activated by a relay with “NO” attached to Green LED and “C” to GND.

The Red LED input is used to indicate access denied. If the RED LED signal is
not connected, the lock will flash RED three times when a non-approved card is
presented indicating loss of connection to the hub rather than access denied. Any
other codes may be reference on the LED reference card.

Micro USB Port

Connect the Wiegand D1, D0, red, and green LED signals.

For Emergency Power & Local (Hard
Wired) Firmware Updates, use micro
USB port located on the side of the K100

Page 15 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

FCC Statement

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

Operation with non-approved equipment is likely to result in interference to radio and TV reception. The user is
cautioned that changes and modifications made to the equipment without the approval of manufacturer could void
the user’s authority to operate this equipment.

IC Statement

This device complies with Industry Canada license-exempt RSS standards(s).
Operation is subject to the following two conditions:

(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation.

Conformité aux normes FCC

Cet équipement a été testé et trouvé conforme aux limites pour un dispositif numérique de classe B,
conformément à la Partie 15 des règlements de la FCC. Ces limites sont conçues pour fournir une protection
raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement génère, utilise
et peut émettre des fréquences radio et, s'il n'est pas installé et utilisé conformément ment aux instructions du
fabricant, peut causer des interferences nuisibles aux communications radio. Rien ne garantit cependant que
l'interférence ne se produira pas dans une installation particulière. Si cet équipement provoque des interférences
nuisibles à la réception radio ou de télévision, qui peut être déterminé en comparant et en l'éteignant, l'utilisateur
est encouragé à essayer de corriger les interférence par une ou plusieurs des mesures suivantes:

1. Réorienter ou déplacer l'antenne de réception.

2. Augmenter la distance entre l'équipement et le récepteur.

3. Branchez l'appareil dans une prise sur un circuit différent de celui auquel le récepteur est connecté.

4. Consultez votre revendeur ou un technicien radio / TV pour assistance.Avertissement

Les changements ou modififications à cet appareil sans expressément approuvée par la partie responsable de
conformité pourraient annuler l'autorité de l'utilisateur de faire fonctionner cet équipement.

Page 16 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1

Conformité aux normes IC

Cet appareil est confrome avec Industrie Canada exempt de license RSS standard(s).
Son fonctionnement est souimes aux deux conditions suivantes:

(1) cet appareil ne peut causer d’interférences, et
(2) cet appareil doit accepter toute interference, y compris des interférences qui peuvent provoquer un

fonctionnement indésirable du périphérique.