APC PF8T3V-GR, PF8T3V-RS User guide [de]

Audio-Video Überspannungsschutz

Modelle PF8T3V-GR/-RS

Vielen Dank für Ihren Kauf eines APC-Überspannungsschutzsystems der Serie PF8! Bitte die Garantiekarte ausfüllen und einsenden oder Online-Garantieformular unter www.apc.com ausfüllen.

Sicherheit

• Gerät nicht während eines Gewi tte r s anschließen.

• Nur zum Gebrauch in geschlossenen Räumen.

• Überspannungsschutz nicht an extrem warmen oder feuchten Orten betreiben. Nicht für Aquarien geeignet.

Anschluss

1. Der Überspannungsschutz muss an einer geerdeten Netzsteckdose angeschlossen werden.

2. Schließen Sie den Netzstecker des Computers und/oder sonstiger elektrischer Geräte an den Anschlussdosen des Überspannungsschutzes

Hinweis:

Die vier Steckdosen mit der Beschriftung „Always On“ führen auch bei ausgeschaltetem Hauptschalter Strom.

Hinweis

: Bitte prüfen Sie nach, ob das zu schützende Gerät einwandfrei funktioniert, bevor Sie es am Überspannungss-

chutz anschließen.

3. Alle Modelle der Serie PF8 sind mit einer Telefonleitungsweiche ausgestattet, die die Telefonleitung und ein eventuell angeschlossenes Faxgerät oder Mode m vor gefäh rlichen Über spannun gen schütz t. Schließen Sie ein Telefonkab el, das an einem Ende mit einem „Westernstecker“ versehen ist, an der Wandanschlussdose und an der Western-Anschlussbuchse

des Überspannungsschutzgerätes (Symbolmarkierung Anschlussbuchse letzte Telefonanschlussbuchse des Überspannungsschutzgerätes über ein weiteres Telefonkabel mit einem Modem

oder Faxgerät.

4. Schließen Sie das von der TV-Kabel-Wandanschlussdose kommende Koaxialkabel an Buchse des Überspannungsschutzes

(Kabel-TV-Anschlussbox, Videorekorder, TV, Kabelmodem) an.

5. Netzschalter

Schutzanzeige

chutz angeschlossen und einges ch alt et, le uch te t die gr ün e S chu tz anzeig e- LED u nd zeigt damit an, dass die angeschlossenen Geräte vor gefährlichen Überspannungen und Blitzschlag geschützt werden. Leuchtet die Lampe bei angeschlossenem und eingeschaltetem Überspannungsschutz nicht, ist die Schutzschaltung beschädigt und kann angeschlossene Geräte nicht mehr schützen. Bitte beim APC-Kundendienst anrufen und um Anweisungen zur Einsendung des Gerätes bitten.

Erdungsanzeige

zeige-LED und zeigt damit an, dass die Netzstec kdos e v or sch rif tsmäß ig geerd et ist. Le uch tet di e E rdun gsa nz eige nic ht,

ist das Stromnetz im Gebäude nicht einwandfrei geerdet. Bitte lassen Sie das Problem durch einen qualifizierten Elektriker beheben.

Kabelführung

auch separat vom Überspannungsschutz an der Wand montierbar (siehe Abbildung).

Schwenkbare Zugentlastung

werden. Dadurch wird die Haltbarkeit des Kabels und des Überspannungsschutz es erhöht. Modell PF8T3V verfügt zusätzlich über eine Überlastanzeige . Wenn diese LED

ene Geräte vom Überspannungsschu tz trennen, bis die Anzeige erlischt.

an.

des Überspannungsschutzes

an.

Schließen Sie das mitgelieferte Koaxialkabel an Buchse

des Überspannungsschutzes einschalten.

- Die Schutzanzeige-LED trägt die Kennzeichnung

– Ist der Überspannungsschutz angeschlossen und eingeschaltet, leuchtet die grüne Erdungsan-

- An dem Gerät angeschlossene Kabel werden sauber gebündelt. Zu diesem Zweck ist die Kabelführung

Das Netzkabel kann je nach Position des Überspannungsschutzes um 180° geschwenkt

und am Telefon, Faxgerät bzw. Modem an. Verbinden Sie die

Schließen Sie ein weiteres Telefonkabel an

und an dem zu schützenden Gerät

220-240V~ 10 A MAX

. Ist der Überspannu ngss-

aufleuchtet, bitte angeschloss-

54,1 mm

Wandbefestigung

PF8VNT3 (Rückansicht)

Bohrlöcher

Technische Daten

Nennbetriebsspannung 220-240 V~, max. 10 A Netzfrequenz 50-60 Hz Betriebstemperatur 0 bis 40 °C Relative Luftfeuchte (Betrieb) 0-95 % nicht kondensierend

Garantie

APC garantiert für die Lebenszeit des Erstkäufers, dass seine Produkte bei bestimmungsgemäßem Gebrauch fr ei von Material- und

Verarbeitungsfehlern sind. Für Geräte, die nicht in einem Mitgliedsland der EU gekauft und/oder verwendet werden, beträgt die Garantiezeit 5 Jahre ab Kaufdatum. Im Rahmen dieser Garantie ist APC verpflichtet , das Produkt im Mangelfall zu reparieren oder zu ersetzen. Zur Inanspruchnahme von Garantieleistungen müssen Sie sich von APC oder einem APC-Service-Center eine Einsendeberechtigungsnummer geben lassen. Bitte schicken Sie das Produkt dann ausreichend frankiert und mit beigelegter Beschreibung des Defekts sowie einem Kaufbeleg mit Datum und Angab e des Geschäfts, in dem das Gerät gekau ft wurde, an den APC Service ein. Diese Garantie gilt nur für den ursprünglichen Käufer.

THIS POLICY IS NOT A WARRANTY. REFER TO APC LIMITED WARRANTY FOR INFORMATION CONCERNING THE WARRANTY FOR YOUR APC PRODUCT. THE

CE Declaration of Conformity

73/23/EEC; 89/336/EEC; 93/68/EEC

Standards to Which Conformity Declared:

Application of Council Directives:

Type of Equipment:

Audio-Video Surge Protector

Model Numbers:

Importer:

American Power Conversion (A. P. C.) b. v. Ballybritt Business Park Galway, Ireland

Place: Galway, Ireland

5 Jan 06

Ray S. Ballard, Managing Director, Europe

2006

BSI 1363, IEC 61643-1:1998+A1; IEC 61643-11:2002

PF8T3V-GR; PF8T3V-RS

Manufacturers:

American Power Conversion 132

Fairgrounds Rd.

West

Kingston, RI 02892 USA

American Power Conversion 2nd

Street

PEZA,

Cavite Economic Zone

Rosario,

Cavite

Philippines

APC India Pvt. Ltd. 187/3,

188/3, Jigani Industrial Area, Jigani

Bangalore,

562106 Karnataka India

American Power Conversion Lot

10, Block 16, Phase 4

PEZA,

Rosario, Cavite

Philippines

American Power Conversion Lot

3, Block 14, Phase 3

PEZA,

Rosario, Cavite

Philippines

APC Brazil LTDA. AI.

Xingu, 850 Barueri Alphaville/Sao

Paulo

06455-030

Brazil

APC (Suzhou) UPS Co., Ltd 339

Suhong Zhong Lu

Suzhou

Industrial Park

Suzhou

Jiangsu 215021

R. China

I, the undersigned, declare under my sole responsibility that the equipment specified

below conforms to the following standards and directives:

American Power Conversion 1600

Division Rd.

West Warwick,

RI 02892 USA

American Power Conversion 40

Catamore Blvd.

East

Providence, RI 02914 USA

American Power Conversion Breaffy

Rd. Castlebar Co

Mayo, Ireland

American Power Conversion Ballybritt

Business Park

Galway,

Ireland

APC Power Infrastructure Co., Ltd 1678,

Ji Xian Road, Tong An Xiamen, P.

R. China 361100

Optimal Benefit Co. (PowerTech

Ind. Co.)

10F,

No. 403 Chung Shan Rd. Sec. 2

Chung

Ho City,

Taipei

Shien Taiwan

LIMITATIONS AND CONDITIONS CONTAINED IN THIS POICY DO NOT AFFECT THE TERMS OF THE WARRANTY.

"Equipment Protection Policy"

The policy is valid in all European Union state members. It is also valid in Norway, Switzerland, Iceland, and Liechtenstein. If your electronic equipment is damaged by power line transients on an AC power line (230V – see Note below) while directly and properly connected to a standard APC product co vered by the Equipment Protection Policy ("connected equipment"), and if all the remaining conditions specified belo w are met, APC will, at APC’s sole option, during the period specified below only, replace the APC product and either a) pay for the repair of the connected equipment or b) reimburse you for the fair market value, as determined by the then current price list of the Boston Computer Exchange (or equivalent), of the connected equipment, in an amount not to exceed the dollar limits stated below, if APC determines that the damage was caused by the failure of the APC product to protect against power line transients and/or where applicable, telephone or CATV (Cable Television) line transients. Power line transients that APC products have been designed to protect against, as recognized by industry standards, include spikes and surges on AC power lines. Protection from telephone line transients applie s o nly t o AP C prod uc ts wh ic h offer mo dem or fa x lin e pr o tect ion , an d in cases in wh ich such protect ion i s available, tele phon e service equipment must include a properly installed and operating "primary protection" device at the service entrance (such devices are normally added during telephone installation) in order to be covered for telephone line transients. Protection of CATV connected equipment from transients applies only to APC products whic h offer such protection, and in such cases, the CATV service must be properly grounded according to the codes set forth in the all applicable national and local electrical and safety codes in order to be covered for CATV transients.

If data is lost from the hard drive in the protected computer due to a malfunction of a properly connected APC product, APC will, at its sole discretion, provide data recovery services from

data recovery labs. This warranty will be offered to customers to the extent commercially reasonable, as determined by APC at its sole discretion. Ontrack will make every commercially

Ontrack reasonable effort to retrieve customer data, however, due to the nature of data loss, recovery is not guaranteed. The data recovery warranty is available on all APC products mentioned in the chart that follows with the exception of APC's Basic Surge Protector models. Data recovery is limited to physical hard drives within protected computing eq uipment. Expressly excluded from this warranty are any type of external storage devices.

APC reserves the right to determine whether the damage to the connected equipment is due to APC product failure by requesting that damaged equipment be sent to APC for ins pection. This policy is in excess of, and applies only to the extent necessary beyond, any coverage for the connected equipment provided by other sources, including, but not limited to, any manufacturer ’s warranty, and any extended warranty coverage.

For customers that meet the qualifications and conditions set forth in this policy, APC will provide reimbursements (cost of repair or fair market value) during the period limits and up to the dollar limit stated as follows:

PF8T3V-GR, PF8T3V-RS 50,000 GBP/75,000 Euros Lifetime

Note: "Lifetime" period is the life of the product while owned by the original purchaser ("you" or "purchaser"). Other period limitations are from the date of purchase.

1. You must register the product by returning to APC the warranty card provided with the product within 10 days of purchase. All information must be filled in, and you should retain a copy for your records.

2. All connected equipment must have a CE mark.

3. The APC product must be plugged into properly wired and grounded outlets; no extension cords, adapters, other ground wires, or electrical connections may be used, with the sole exception of other standard APC 230V products. The installation must not inc lude power protection product s by any manufacturer other than APC. The insta llation must co mply with all a pplicable local electrical and safety codes.

4. Any claim under the Equipment Protection Policy must be made within 10 days of the day of alleged damage to the connected equipment.

5. The Equipment Protection Policy covers only those product models listed above and is valid in all Eurpean Union state members, as well as Norway, Switzerland, Iceland, and Liechtenstein.

1. DAMAGE TO ELECTRONIC EQUIPMENT RESULTING FROM TRANSIENTS ON DATA LINES IS NOT COVERED.

2. Restoration of lost data and reinstallation of software are not covered.

3. This policy does not cover damage from a cause other than AC power line transients, except for damage due to telephone line or CATV transients, which is covered only if the APC product offers such protection.

4. DAMAGE CAUSED BY FAILURE TO PROVIDE A SUITABLE INSTALLATION ENVIRONMENT FOR THE PRODUCT (INCLUDING, BUT NOT LIMITED TO, LACK OF A PROPER SAFETY GROUND).

5. Damage caused by the use of the APC product for purposes other than those for which it was designed.

6. Damage caused by accidents, or disasters such as fire, flood, or wind.

7. Damage caused by abuse, misuse, alternation, modification, or negligence.

8. This policy is null and void if, in APC’s view, the APC product has been tampered with or altered in any way.

9. EXCEPT AS EXPRESSLY PROVIDED IN THIS POLICY, IN NO CASE SHALL APC BE LIABLE UNDER THE TERMS OF THIS POLICY FOR ANY DAMAGES WHATSOEVER, INCLUDING, BUT NOT LIMITED TO, DIRECT, INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR MULTIPLE DAMAGES ARISING OUT OF THE USE OF THE APC PRODUCT OR DAMAGE TO THE CONNECTED EQUIPMENT, REGARDLESS OF THE LEGAL THEORY ON WHICH SUCH CLAIM IS BASED, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. SUCH DAMAGES INCLUDE BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF SAVINGS OR REVENUE, LOSS OF USE OF THE APC PRODUCT OR THE CONNECTED EQUIPMENT OR ANY ASSOCIATED EQUIPMENT, LOSS OF SOFTWARE, COST OF CAPITAL, COST OF ANY SUBSTITUTE EQUIPMENT, FACILITIES OR SERVICES, DOWNTIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY.

1. If all of the conditions for coverage are satisfied, call the APC customer service department (see list at the end of the document for respective phone numbers) and obtain an EPP RMA (Equipment Protection Policy Returned Material Authorization) number. APC will forward you an Equipment Protection Policy claim form, which must be completed and filed within 30 days.

2. Mark the Equipment Protection Policy RMA number on the product you are returning.

3. Pack the APC product in its original packaging (or request packing materials from APC if the packaging has been discarded). Encl ose the comp leted Equi pmen t Policy claim form and a copy of your sales receipt for the APC product in box.

4. Mark the EPP RMA number clearly on the outside of box.

5. Ship the product (one way shipping charges paid by you) to: American Power Conversion, Technical Support, Ballybrit Business Park, Galway, Ireland Tel. +353 91 702000.

6. APC will evaluate the product to determine its level of functionality, and will examine the product for evidence of damage from AC line transients (telephone line or CATV transients, if applicable). (A) If APC ’s evaluation provides no eviden ce of damage from power lin e transients (telephone line or CATV transients, if applicable), APC will send to the customer (i) a report summarizing the tests performed and (ii) a rejection of claim notice. (B) If the APC product shows evidence of damage from power line transients (telephone line or CATV transients, if applicable), APC will request that all con nected equipment for whi ch an Equipment Protection Po licy claim has been submitted, b center. If it is determined that the connected equipment has been damaged from AC power line transients (telephone line or CATV transients, if applicable), APC will, in its discretion , either authorize you to have the equipment repaired or reimburse you for the fair market value of the damaged equipment, up to the dollar limits stated above.

7. If you are authorized by APC to have the connected equipment repaired, the repair must be performed at a service center that is authorized by the manufacturer of the connected equipment. APC reserves the right to contact the authorized service centre directly to discuss repair costs and damage to the connected equipment to determine if it was caused by AC power line transients (telephone line or CATV transients, if applicable) and the right to request that the service centre forward the connected equipment or components to APC for inspection.

8. APC will, after determining that th e dam age was caused b y the fail ure of the APC produ ct to protect against AC power line transient s (teleph one line or CATV transients, if applicable), issue payment to you, in its sole discretion, for either costs of repair of the fair market value of the connected equipment, up to the dollar limits stated above. APC reserves the right to require you to transfer title and deliver the connected equipment to APC if it chooses to reimburse you for the fair market value of the connected equipment.

9. Unless modified in a writing signed by APC and you, the terms of this policy are understood to be the complete and exclusive agreement between the parties, superseding all prior agreements, oral and written, and all other communications between the parties relating to the subject matte r of this agreement. No employee of APC or any other party is authorized to make any representations beyond those made in this agreement concerning the Equipment Protection Policy.

Product Amount Period

“Data Recovery Policy”

Equipment Protection Policy Dollar and Period Limits:

Eligibility for coverage under the Equipment Protection Policy:

What is not covered under the Equipment Protection Policy:

Submitting an Equipment Protection Policy Claim:

e sent for evaluation to either APC or an authorized service

CE Declaration of Conformity

Date of product declaration

I, the undersigned, declare under my sole responsibility that the equipment specified below conforms to the following standards and directives:

Standards to Which Conformity Declared:

Application of Council Directives:

Type of Equipment:

Model Numbers:

American Power Conversion Ballybritt Business Park Galway, Ireland

American Power Conversion Breaffy Rd. Castlebar Co Mayo, Ireland

American Power Conversion 132 Fairgrounds Rd. West Kingston, RI 02892 USA

American Power Conversion 1600 Division Rd.

American Power Conversion 2nd Street PEZA, Cavite Economic Zone Rosario, Cavite Philippines

American Power Conversion Lot 10, Block 16, Phase 4 PEZA, Rosario, Cavite Philippines

American Power Conversion Lot 3, Block 14, Phase 3 PEZA, Rosario, Cavite Philippines

BSI 1363, IEC 61643-1:1998+A1; IEC 61643-11:2002

73/23/EEC; 89/336/EEC; 93/68/EEC

Audio-Video Surge Protector

PF8T3V-GR; PF8T3V-RS

APC (Suzhou) UPS Co., Ltd 339 Suhong Zhong Lu Suzhou Industrial Park Suzhou Jiangsu 215021 P. R. China

APC Power Infrastructure Co., Ltd 1678, Ji Xian Road, Tong An Xiamen, P. R. China 361100

Optimal Benefit Co. (PowerTech Ind. Co.) 10F, No. 403 Chung Shan Rd. Sec. 2 Chung Ho City, Taipei Shien Taiwan

West Warwick, RI 02892 USA

APC Brazil LTDA. AI. Xingu, 850

American Power Conversion 40 Catamore Blvd. East Providence, RI 02914 USA

Barueri Alphaville/Sao Paulo 06455-030 Brazil

APC India Pvt. Ltd. 187/3, 188/3, Jigani Industrial Area, Jigani Bangalore, 562106 Karnataka India

American Power Conversion (A. P. C.) b. v. Ballybritt Business Park Galway, Ireland

Place: Galway, Ireland

Ray S. Ballard, Managing Director, Europe

5 Jan 06

Entire contents copyright 2006 by American Power Conversion Cor poration. All rights reserved. Reproduction in whole or in part without permission is prohibited APC and the APC logo are registered trademarks of American Power Conversion Corporation. All other trademarks are the property of their respective owners.

990-2924 4/2006