APC P5BT-FR, P5BV-FR, P5BT-IT, P5BV-IT, P5BT-SP User guide [hu]

...

w w w

.apc.com

w w w

.apc.com

Alap túlfeszültség-védő

w w w

.apc.com

Modellek: P5BT-FR, P5BV-FR, P5BT-IT, P5BV-IT, P5BT-SP,

P5BV-SP, P5BT-GR, P5BV-GR, P5BT-RS és P5BV-RS

Köszönjük, hogy megvásárolta az APC P5 sorozatú túlfeszültség védőjét. Kérjük, töltse ki és postán küldje vissza a

Garancia jegyet, vagy töltse ki a www. apc.com honlapról letölthető Garancia regisztrációs űrlapot. Megjegyzés: ebben a kézikönyvben csak egy "T" és egy "V" modellt mutatunk be.

Biztonság

• Ne telepítse az eszközt villámlás idején.

• Csak beltéri használatra.

• Ne telepítse a túlfeszültség védőt forró vagy túlságosan nedves helyre; ne használja akvárium berendezéshez.

Telepítés

1. Kizárólag földelt konnektorba dugja be a túlfeszültség-védőt.

2. Dugja be számítógép és/vagy egyéb elektromos berendezés hálózati kábelét a túlfeszültség-védő kimeneteibe Megjegyzés: Ellenőrizze, hogy a védendő készülék megfelelően működik, mielőtt bedugja a túlfeszültség-

védőbe.

3. P5BT-FR, P5BT-GR, P5BT-RS, P5BT-IT és P5BT-SP modellek esetén csatlakkoztasson egy moduláris telefonkábelt a telefon fali kimenete és a túlfeszültség-védő egy másik moduláris telefonkábelt a túlfeszültség-védő

faxkészülék közé.

4. P5BV-FR, P5BV-GR, P5BV-RS, P5BV-IT és P5BV-SP modellek esetén, csatlakoztasson a kábelkimenetből érkező koaxiális kábelt az kábelt a levédett berendezéshez (CATV doboz, VCR, TV, kábel modem).

5. Állítsa a Hálózati kapcsolót

Védelemjelző - A P5B-FR, P5B-GR, P5B-RS, P5B-IT és P5B-SP védelemjelző

ellátva: 220-240V~ max. 10 A. Amikor az egység be van dugva és be van kapcsolva, az védelemjelző világít így jelezve, hogy a túlfeszültség-védő alkalmas a berendezés védelmének ellátására a káros elektromos túlfeszültségekkel szemben. Ha a jelzőfény nem világít, amikor az egység be van dugva és be van kapcsolva, akkor az egység tartósan sérült és nem képes megvédeni a berendezést. Ebben az esetben vissza kell küldeni az ATC Műszaki ügyfélszolgálata által adott utasításoknak megfelelően.

Földelés rendben jelző - Amikor a túlfeszültség-védő be van dugva és be van kapcsolva, a Földelés rendben

jelző

➑ világít (zöld) ezzel jelezve, hogy a hálózati kimenet megfelelően földelve van. Ha a Földelés rendben jelző

nem világít, valami probléma van az épület vezetékeivel. Hívjon szakképzett villanyszerelőt a probléma kijavítására.

Kábelrendező vezető

falra is felszerelhető a túlfeszültség-védővel együtt (lásd alább).

Forgó feszülés mentesítő

hálózati kábel és a túlfeszülltség-védő élettartamát.

➊.

➋ jelű dugaszhüvelye közé . Csatlakoztasson

➌ jelű dugaszhüvelye és a telefon, modem vagy

➍ jelű csatlakozóhoz . Csatlakoztassa a ➎ jelű csatlakozóból jövő koaxiális

➏ BE pozícióba.

➐ a következő jelöléssel van

➒ - a mellékelt kábelrendező segítségével a hálózati kábelek rendezetten tarthatóak és a

➓ - lehetővé teszi a hálózati kábel 180 fokos fel-leforgatását, ezzel megnövelve a

➐

➑

Falra szereléssel kapcsolatos információk

➏ ➋

➊

➒

P5BT-FR

Műszaki adatok

Névleges üzemi feszültség 220-240 V AC, max. 10 A Frekvenciatartomány 50- 60 Hz Üzemi hőmérséklet 0 - 40 °C (32 - 104 °F) Megengedett relatív

páratartalom

Korlátozott garancia

Az APC garanciát vállal arra, hogy az eredeti vásárló általi rendeltetésszerű használat és szervizelés

esetén, termékeik élettartamuk végéig anyagi és gyártási hibáktól mentesek lesznek (Németországban a garanciális időszak a termék vásárlási dátumától számított 30 év). Az Európai Közösségen kívül eső országokban használt egységek esetén a garancia a vásárlástól számított 5 évig érvényes. AZ APC arra vállal garanciát, hogy a hibás készüléket saját döntése alapján megjavítja vagy kicseréli. A garanciális szervizeléshez kérnie kell egy Visszaküldött anyag engedély (RMA) számot az APC-től vagy az APC Szerviz központjától előre leróva a szállítási költségeket, és mellékelnie kell a probléma rövid leírását, illetve a vásárlás idejét és helyét igazoló dokumentumot. A garancia csak az eredeti vásárlóra vonatkozik.

➌

➓

Kábelrendezés

Vezető rögzítő nyílásai

0 - 95 %, nem kondenzáló

48 mm

(1.89”)

Ház

Rögzítő nyílások

THIS POLICY IS NOT A WARRANTY. REFER TO APC LIMITED WARRANTY FOR INFORMATION CONCERNING THE WARRANTY FOR YOUR APC PRODUCT. THE LIMITATIONS AND CONDITIONS CONTAINED IN THIS POICY DO NOT AFFECT THE TERMS OF THE WARRANTY.

"Equipment Protection Policy"

The policy is valid in all European Union state members. It is also valid in Norway, Switzerland, Iceland, and Liechtenstein. If your electronic equipment is damaged by power line transients on an AC power line (230V – see Note below) while directly and properly connected to a standard APC product covered by the Equipment Protection Policy ("connected equipment"), and if all the remaining conditions specified below are met, APC will, at APC’s sole option, during the period specified below only, replace the APC product and either a) pay for the repair of the connected equipment or b) reimburse you for the fair market value, as determined by the then current price list of the Boston Computer Exchange (or equivalent), of the connected equipment, in an amount not to exceed the dollar limits stated below, if APC determines that the damage was caused by the failure of the APC product to protect against power line transients and/or where applicable, telephone or CATV (Cable Television) line transients. Power line transients that APC products have been designed to protect against, as recognized by industry standards, include spikes and surges on AC power lines. Protection from telephone line transients applies only to APC products which offer modem or fax line protection, and in cases in which such protection is available, telephone service equipment must include a properly installed and operating "primary protection" device at the service entrance (such devices are normally added during telephone installation) in order to be covered for telephone line transients. Protection of CATV connected equipment from transients applies only to APC products which offer such protection, and in such cases, the CATV service must be properly grounded according to the codes set forth in the all applicable national and local electrical and safety codes in order to be covered for CATV transients.

“Data Recovery Policy”

If data is lost from the hard drive in the protected computer due to a malfunction of a properly connected APC product, APC will, at its sole discretion, provide data recovery services from Ontrack

data recovery labs. This warranty will be offered to customers to the extent commercially reasonable, as determined by APC at its sole discretion. Ontrack will make every commercially reasonable effort to retrieve customer data, however, due to the nature of data loss, recovery is not guaranteed. The data recovery warranty is available on all APC products mentioned in the chart that follows with the exception of APC's Basic Surge Protector models. Data recovery is limited to physical hard drives within protected computing equipment. Expressly excluded from this warranty are any type of external storage devices.

APC reserves the right to determine whether the damage to the connected equipment is due to APC product failure by requesting that damaged equipment be sent to APC for inspection. This policy is in excess of, and applies only to the extent necessary beyond, any coverage for the connected equipment provided by other sources, including, but not limited to, any manufacturer’s warranty, and any extended warranty coverage.

Equipment Protection Policy Dollar and Period Limits:

For customers that meet the qualifications and conditions set forth in this policy, APC will provide reimbursements (cost of repair or fair market value) during the period limits and up to the dollar limit stated as follows:

Product Amount Period

P5BT-FR, P5BT-IT, P5BT-GR, P5BT-RS, P5BT-SP, P5BV-FR, P5BV-IT, 35,000 GBP/50,000 Euros Lifetime P5BV-GR, P5BV-RS, P5BV-SP

Note: "Lifetime" period is the life of the product while owned by the original purchaser ("you" or "purchaser"). Other period limitations are from the date of purchase.

Eligibility for coverage under the Equipment Protection Policy:

1. You must register the product by returning to APC the warranty card provided with the product within 10 days of purchase. All information must be filled in, and you should retain a copy for

your records.

2. All connected equipment must have a CE mark.

3. The APC product must be plugged into properly wired and grounded outlets; no extension cords, adapters, other ground wires, or electrical connections may be used, with the sole exception of

other standard APC 230V products. The installation must not include power protection products by any manufacturer other than APC. The installation must comply with all applicable local electrical and safety codes.

4. Any claim under the Equipment Protection Policy must be made within 10 days of the day of alleged damage to the connected equipment.

5. The Equipment Protection Policy covers only those product models listed above and is valid in all Eurpean Union state members, as well as Norway, Switzerland, Iceland, and Liechtenstein.

What is not covered under the Equipment Protection Policy:

1. DAMAGE TO ELECTRONIC EQUIPMENT RESULTING FROM TRANSIENTS ON DATA LINES IS NOT COVERED.

2. Restoration of lost data and reinstallation of software are not covered.

3. This policy does not cover damage from a cause other than AC power line transients, except for damage due to telephone line or CATV transients, which is covered only if the APC product

offers such protection.

4. DAMAGE CAUSED BY FAILURE TO PROVIDE A SUITABLE INSTALLATION ENVIRONMENT FOR THE PRODUCT (INCLUDING, BUT NOT LIMITED TO, LACK OF A

PROPER SAFETY GROUND).

5. Damage caused by the use of the APC product for purposes other than those for which it was designed.

6. Damage caused by accidents, or disasters such as fire, flood, or wind.

7. Damage caused by abuse, misuse, alternation, modification, or negligence.

8. This policy is null and void if, in APC’s view, the APC product has been tampered with or altered in any way.

9. EXCEPT AS EXPRESSLY PROVIDED IN THIS POLICY, IN NO CASE SHALL APC BE LIABLE UNDER THE TERMS OF THIS POLICY FOR ANY DAMAGES WHATSOEVER,

INCLUDING, BUT NOT LIMITED TO, DIRECT, INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR MULTIPLE DAMAGES ARISING OUT OF THE USE OF THE APC PRODUCT OR DAMAGE TO THE CONNECTED EQUIPMENT, REGARDLESS OF THE LEGAL THEORY ON WHICH SUCH CLAIM IS BASED, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. SUCH DAMAGES INCLUDE BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF SAVINGS OR REVENUE, LOSS OF USE OF THE APC PRODUCT OR THE CONNECTED EQUIPMENT OR ANY ASSOCIATED EQUIPMENT, LOSS OF SOFTWARE, COST OF CAPITAL, COST OF ANY SUBSTITUTE EQUIPMENT, FACILITIES OR SERVICES, DOWNTIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY.

Submitting an Equipment Protection Policy Claim:

1. If all of the conditions for coverage are satisfied, call the APC customer service department (see list at the end of the doc

ument for respective phone numbers) and obtain an EPP RMA

(Equipment Protection Policy Returned Material Authorization) number. APC will forward you an Equipment Protection Policy claim form, which must be completed and filed within 30 days.

2. Mark the Equipment Protection Policy RMA number on the product you are returning.

3. Pack the APC product in its original packaging (or request packing materials from APC if the packaging has been discarded). Enclose the completed Equipment Policy claim form and a copy

of your sales receipt for the APC product in box.

4. Mark the EPP RMA number clearly on the outside of box.

5. Ship the product (one way shipping charges paid by you) to:

American Power Conversion, Technical Support, Ballybrit Business Park, Galway, Ireland Tel. +353 91 702000.

6. APC will evaluate the product to determine its level of functionality, and will examine the product for evidence of damage from AC line transients (telephone line or CATV transients, if

applicable). (A) If APC’s evaluation provides no evidence of damage from power line transients (telephone line or CATV transients, if applicable), APC will send to the customer (i) a report summarizing the tests performed and (ii) a rejection of claim notice. (B) If the APC product shows evidence of damage from power line transients (telephone line or CATV transients, if applicable), APC will request that all connected equipment for which an Equipment Protection Policy claim has been submitted, be sent for evaluation to either APC or an authorized service center. If it is determined that the connected equipment has been damaged from AC power line transients (telephone line or CATV transients, if applicable), APC will, in its discretion, either authorize you to have the equipment repaired or reimburse you for the fair market value of the damaged equipment, up to the dollar limits stated above.

7. If you are authorized by APC to have the connected equipment repaired, the repair must be performed at a service center that is authorized by the manufacturer of the connected equipment.

APC reserves the right to contact the authorized service centre directly to discuss repair costs and damage to the connected equipment to determine if it was caused by AC power line transients (telephone line or CATV transients, if applicable) and the right to request that the service centre forward the connected equipment or components to APC for inspection.

8. APC will, after determining that the damage was caused by the failure of the APC product to protect against AC power line transients (telephone line or CATV transients, if applicable), issue

payment to you, in its sole discretion, for either costs of repair of the fair market value of the connected equipment, up to the dollar limits stated above. APC reserves the right to require you to transfer title and deliver the connected equipment to APC if it chooses to reimburse you for the fair market value of the connected equipment.

9. Unless modified in a writing signed by APC and you, the terms of this policy are understood to be the complete and exclusive agreement between the parties, superseding all prior agreements,

oral and written, and all other communications between the parties relating to the subject matter of this agreement. No employee of APC or any other party is authorized to make any

990-1965A

APC, the APC logo, and Back-UPS are trademarks of American Power Conversion Corporation. All other trademarks, product names,

and corporate names are the property of their respective owners and are used for informational purposes only.

Date of product declaration