DANGER
WARNING
CAUTION
NOTICE
User Manual Easy UPS
SNMP Card APV9602
The addition of this symbol to either a “Danger” or “Warning” safety label indicates that an
electrical hazard exists which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible injury or death.
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate
injury.
NOTICE is used to address practices not related to physical injury.
Important Safety Messages
Read the instructions carefully and look at the equipment to become familiar with the device before trying to install,
operate, service or maintain it. The following special messages may appear throughout this document or on the
equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of this symbol to a Danger or Warning product safety label indicates that an electrical hazard exists
that will result in personal injury if the instructions are not followed.
Product Description
(1)
SNMP Card
(1)
User manual
(1)
Utility CD
The SNMP Card is sensitive to static electricity. When handling the SNMP Card, touch only
the end plate while using one or more of these electrostatic-discharge devices (ESDs): wrist
straps, heel straps, toe straps, or conductive shoes.
Integrated with Easy UPS LI SNMP Manager software, devices with the SNMP Card installed can be
monitored and controlled in LAN.
APV9602 SNMP Card:
Provides SNMP MIB to monitor & control UPS.
Auto-senses 10M /100M/1000M Fast Ethernet Manage and configure via Web Browser or NMS.
Supports TCP/IP, UDP, SNMP, HTTPS, SMTP, FTPS Protocols.
Supports SSL/TLS Encryptions.
Provides easy setup and upgrade tools via Easy UPS LI SNMP Manager software.
Sends SNMP TRAP; E-mail for events notification.
Emails daily UPS history report.
Performs graceful shutdown via Easy UPS LI Shutdown software.
Devices in which you can install the SNMP Card
The SNMP Card can be installed in any compatible device that has an Intelligent Card Slot, including:
Easy UPS: SMV series UPS
Package Contents
The packaging is recyclable; save it for reuse or dispose of it properly.
Disclaimer
APC by Schneider Electric is not responsible for damage sustained during reshipment of this product.
2 SNMP Card APV9602
Product Overview
●
1
10/100 Base-T connector
Connects SNMP card to the Ethernet network.
●
2
Status LED
See “Status LED”.
Color LED
Condition
Description
100M LED (Green)
Flash
Port is operating at 100Mbit/s
Off
Card is not connected to the network
10M LED (Yellow)
Flash
Port is operating at 10Mbit/s
Off
Card is not connected to the network
LED(Red)
Flash
Lost UPS connection
Off
Connecting with UPS
LED(Yellow)
On
SNMP card is operating
Off
SNMP card stop working
Front Panel
Status LED
Note:
The port is operating at 1000Mbit/s when both Green(100M) and Yellow(10M) LED illuminating.
DO NOT turn off power when updating firmware. LED (red) will keep flashing.
SNMP Card APV9602 3
Specifications
Physical
Dimensions with package
Width x Height x Depth
180 mm(7.09in) x 60 mm(2.36in) x 150 mm(5.9in)
Dimensions without
package
Width x Height x Depth
51.76 mm(2.04in) x 25.8 mm(1.02in) x 80.31 mm(3.16 in)
Weight with package
0.3 kg (0.66 lb)
Weight without package
0.03 kg (0.07 lb)
Temperature
Operating
0 to 60°C (32 to 140°F)
Storage
-40 to 85°C (-40 to 185°F)
Humidity
Operating
10 to 90% relative humidity, non-condensing
Supported
Protocol
Network
Auto-sense 10M /100M/1000M Fast Ethernet Manage and
configure via Web Browser or NMS
Network Protocol
TCP/IP, UDP, SNMP, HTTPS, SMTP, FTPS,
SNMP MIB
RFC1628, PPC
4 SNMP Card APV9602
Installation
Please turn off power to install the SNMP card in a supported Easy UPS.
The SNMP Card is sensitive to static electricity. When handling the SNMP Card, touch only the end
plate while using one or more of these electrostatic-discharge devices (ESDs): wrist straps, heel straps,
toe straps, or conductive shoes.
For the location of the UPS Intelligent Card Slot, see the UPS User Manual.
Install the SNMP card
1. Remove the cover of Intelligent Card Slot on the back of the UPS and retain the screws.
2. Slide the card into the open slot and secure with the screws from step 1. (See below chart)
3. Connect a network interface cable to the 10/100 Base-T network connector (RJ-45) on the SNMP Card.
When the network interface cable is connected, the SNMP Card will attempt to obtain an IP address via DHCP.
See “Configuration methods” on page 6.
Configure the SNMP Card and Monitoring
See “Quick Configuration” on page 6.
SNMP Card APV9602 5
Quick Configuration
Configuration Method
1. Please install Easy UPS LI SNMP Manager software in your PC. When running Easy UPS LI SNMP
Manager, it will automatically search available SNMP cards within the network with its serial number, IP
address, MAC address. (List refreshes automatically every 2 minutes)
2. Select your SNMP card from the list and click Launch Web User Interface to login to Easy UPS LI SNMP
WebUI webpage.
Please check software manual in the CD for more information.
6 SNMP Card APV9602
SNMP Card APV9602 7
APC by Schneider Electric Worldwide Customer
EN 990-6137
01/2020
Support
Customer support for this or any other APC by Schneider Electric product is available at no charge in any of
the following ways:
•
Visit the APC by Schneider Electric website to access documents in the APC by Schneider Electric
Knowledge Base and to submit customer support requests.
–
www.apc.com
Connect to localized APC by Schneider Electric websites for specific countries, each of which
provides customer support information.
–
www.apc.com/support/
Global support searching APC by Schneider Electric Knowledge Base and using e-support.
•
Contact the APC by Schneider Electric Customer Support Center by telephone or e-mail.
–
Local, country specific centers: go to
for contact information.
For information on how to obtain local customer support, contact the APC by Schneider Electric
representative or other distributor from whom you purchased your APC by Schneider Electric product.
(Corporate Headquarters)
www.apc.com/support/contact
© 2020 APC by Schneider Electric. APC, the APC logo are owned by Schneider
Electric Industries S.A.S., or their affiliated companies. All other trademarks are
property of their respective owners.
Loading...