Apantac OG-MINIQ-SET-1 Users Guide

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 1 of 31

TAHOMA MiniQ

Multiviewers

HARDWARE MANUAL

Version 1.0
Dated: November 19, 2012

© 2012 Apantac LLC - All rights reserved

The contents of this document are provided in connection with Apantac LLC (“Apantac”) products. Apantac makes no
representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right
to make changes to specifications and product descriptions at any time without notice.

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 2 of 31

TABLE OF CONTENTS

TRADEMARKS ....................................................................................... 3

!

COMPLIANCE INFORMATION ................................................................. 3

!

Limitation of Liability ........................................................................... 4

!

Extended Warranty Options ................................................................. 5

!

Services and Repairs Outside the Warranty Period ................................. 5

!

Disclaimer .......................................................................................... 5

!

Operating Environment ........................................................................ 5

!

INTRODUCTION TO TAHOMA MiniQ MULTIVIEWERS ............................... 6

!

!!!

HARDWARE ........................................................................................ 6

!

!!!

TAHOMA MiniQ PRODUCT ................................................................... 7

!

TECHNICAL SPECIFICATIONS .............................................................. 8

!

SPECIFICATIONS .............................................................................. 11

!

PRODUCT CONTENTS - “WHAT’S IN THE BOX” ................................... 14

!

!!

OPERATION ...................................................................................... 18

!

Optional Hardware .............................................................................. 18

!

MiniQ MULTIVIEWER SETUP EXAMPLES ............................................... 19

!

ACCESSORIES ..................................................................................... 24

!

!!

Standard Accessories: ........................................................................ 24

!

!!

Optional Accessories: ............................. Error! Bookmark not defined.

!

APPENDIX A: CONNECTORS ............................................................... 25

!

APPENDIX B: External DC POWER SUPPLIES ........................................ 29

!

CONTACT APANTAC ............................................................................ 31

!

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 3 of 31

TRADEMARKS

Apantac, Tahoma, MT Hood, Crescent and Mazama are registered trademarks of Apantac LLC.
All other trademarks are the property of their respective holders.

Notice:

Copyright © 2012 Apantac LLC. All rights reserved. All information in this manual is subject to
change without notice. No part of the document may be reproduced or transmitted in any form,
or by any means, electronic or mechanical, including photocopying or recording, without the
express written permission of Apantac LLC.

1B

COMPLIANCE INFORMATION

The Apantac equipment has been tested to comply with the following.

• FCC - Class A

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his or her own expense.

• CE

• C-Tick

• RoHS

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 4 of 31

2B

WARRANTY STATEMENT

Apantac LLC (herein after referred to as “Apantac”) warrants to the original purchaser of the
products manufactured by Apantac (the “Product,”) will be free from defects in material and
workmanship for a period of three (3) year from the date of shipment of the Product to the
purchaser.

If the Product proves to be defective during the three (3) year warranty period, the purchaser’s
exclusive remedy and Apantac’s sole obligation under this warranty is expressly limited, at
Apantac’s sole option, to:

(a) repair the defective Product without charge for parts and labor or,
(b) provide a replacement in exchange for the defective Product or,
(c) if after a reasonable time, is unable to correct the defect or provide a replacement

Product in good working order, then the purchaser shall be entitled to recover damages
subject to the limitation of liability set forth below.

19BLimitation of Liability

Apantac’s liability under this warranty shall not exceed the purchase price paid for the defective
product. In no event shall Apantac be liable for any incidental, special or consequential
damages, including without limitation, loss of profits for any breach of this warranty.

If Apantac replaces the defective Product with a replacement Product as provided under the
terms of this Warranty, in no event will the term of the warranty on the replacement Product
exceed the number of months remaining on the warranty covering the defective Product.

Equipment manufactured by other suppliers and supplied by Apantac carries the respective
manufacturer’s warranty. Apantac assumes no warranty responsibility either expressed or
implied for equipment manufactured by others and supplied by Apantac.

This hardware warranty shall not apply to any defect, failure or damage:

a) Caused by improper use of the Product or inadequate maintenance and care of the

Product;

b) Resulting from attempts by those other than Apantac representatives to install, repair,

or service the Product;

c) Caused by installation of the Product in a hostile operating environment or connection of

the Product to incompatible equipment;

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 5 of 31

d) Caused by the modification of the Product or integration with other products when the

effect of such modification or integration increases the time or difficulties of servicing
the Product. Any Product which fails under conditions other than those specifically
covered by the Hardware Warranty, will be repaired at the price of parts and labor in
effect at the time of repair. Such repairs are warranted for a period of ninety (90) days
from date of reshipment to customer.

20BUExtended Warranty Options

Apantac offers

OPTIONAL

Extended Warranty plans that provide continuous coverage for the
Product after the expiration of the Warranty Period. Please contact an Apantac sales
representative for details on the options that are available for your Apantac equipment.

21BUServices and Repairs Outside the Warranty Period

Apantac makes its best offer to repair products that are outside the warranty period, provided
the product has not reached its end of life.

22BUDisclaimer

Use of this product is limited to the intended design purpose. Any damage caused by use other
than the design purpose will void the above warranty.

23BUOperating Environment

Apantac Tahoma Multiviewers should be operated in an environment that is safe for sensitive
electronic equipment. It should not be placed in hot, dusty, or humid locations without
adequate cooling, filtration, or ventilation.

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 6 of 31

4B!

INTRODUCTION TO TAHOMA MiniQ MULTIVIEWERS

The Apantac Tahoma MiniQ Multiviewer platform displays multiple auto-detecting video inputs
at different formats on a high resolution display up to resolutions of 1920x1200. The Tahoma
MiniQ Platform combines the display of video windows, audio meters, label/UMD, tallies, alarms
and indicators in a very space efficient package

5B

HARDWARE

The Apantac Tahoma MiniQ Multiviewer Platform consists of the following

4 different sizes of mechanical frames to serve the needs of broadcast, professional AV and
surveillance markets. These frames are ½ width of 1 RU, 1 RU, RU and 3RU. Each Multiviewer
frame has a unique IP address, which allows a PC/laptop to easily connect and configure the
display layouts.

1. MiniQ Module-> A quad video processor that allows 4 video inputs from CV, SD/HD-SDI
to 3G SDI

2. MiniQ-3U-FR -> 3 rack unit frame that can house up to 8 MiniQ modules, comes with 2
MiniQ-3U-PS (hot swappable power supplies)

3. MiniQ-1U-FR -> 1 rack unit mounting plate that can provide rack mount for up to 3
MiniQ modules

4. MiniQ-1U-PS -> External DC power supply for single MiniQ module

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 7 of 31

6B

TAHOMA MiniQ PRODUCT

A fully configured MiniQ-3U-FR consists of 8 MiniQ moudules. It can accepts up to
32 various video standards (from analog composite to HD-SDI and 3G) and comes
standard with

• 16 channels of embedded audio per every SDI video input

• 1 HDMI/DVI extender RJ45 outputs

• 1 SDI output

• 8 GPI (RJ50)

• 1 IP port (RJ45)

• 1 Analog audio monitoring output (Phoenix connector)

The MiniQ modules can be cascaded together with t-Link cables to freely configure its
Flexible outputs.

*Flexible Outputs Examples:

Table 1: Flexible outputs

Output(s)

1 2 3 4 5 6 7 8

Inputs

4 4 4 4 4 4 4

4

Inputs

4 4 4 4 4 4 8

Inputs

4 4 4 4 8

8

Inputs

4 4 8 8 8

Inputs

4 4 4 4 8

12

Inputs 8 8 8 8

Inputs

8

16

4

4

Inputs 4 8 8 12

Inputs

4 4 8

16

Inputs

8

12

12

Inputs

4

12

16

Inputs 8 8

16

Inputs 4 8

20

Inputs 4 4

24

Inputs

4

28

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 8 of 31

Inputs

8

24

Inputs

12

20

Inputs

16

16

Inputs

32

TECHNICAL SPECIFICATIONS

• Auto detect 3G/HD-SD/SDI/CV 50/60Hz

• Output resolution up to 1920x1200/1080p

• Digital clock can be synchronized with NTP

• Up to 30 presets for display layout

• Presets can be recalled via GPI or ASCII protocol via network

• Auto-detect aspect ratio between 16x9 and 4x3

• Communication interface via IP or RS232

• Supports Apantac eXtended Protocol (AXP)

• Supports direct TSL tally/UMD interface

• Supports multiple languages (including 2 byte characters)

• Supports SDI output (optional)

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 9 of 31

Table 2: Serial Video input

Standards

Upgradable to 3Gb/s (SMPTE 424M)
HD-SDI (SMPTE 292M)
SD-SDI (SMPTE 259M-C)
PAL/NTSC

Connector

BNC

Equalization

Automatic to 140m (Belden 1694A)

Return Loss

15db up to 270mb/s

Embedded Audio

SMPTE 272-A

Table 3: Video Formats supported

480i

720p/30

1080p/23.98

2048x1080p/23.98

480p

720p/50

1080p/24

2048x1080p/24

576i

720p/59.94

1080p/25

576p

720p/60

1080p/29.97

720p/23.98

1035i/59.94

1080p/30

720p/24

1035i/60

1080sf/23.98

720p/25

1080i/50

1080sf/24

720p/29.97

1080i/59.94

1080sf/30

Table 4: Display Output

Standards

DVI-D, HDMI 1.2/3, VGA up to 1920x1200,
SDI

Connector

RJ45 (with transmitter), BNC

Impedance

100Ω, 75Ω

Table 5: Audio Outputs

Type

Number/type/connector

Location

Adjustment

Stereo Analog

1 / unbalanced / phoenix
connector

Rear Panel

None, Line Level

Table 6: Output Resolution (50 and 60Hz)

720x480

852x480

1024x768

1280x768

800x600

1280x960

1280x1024

1360x768

1280x800

1400x1050

1600x1200

1680x1050

1366x768

1920x1080

1920x1200

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 10 of 31

TabLE-7: General Purpose Interface I/O

Number

On MiniQ Module

8

Assignable to input or output

Connector

RJ50 to DB9

Figure 1: GPI/O Electrical Characteristics

Table 8: Serial Port

Number of Ports

1 x RS232

Adapter

RS232 to RS422 or RS485 (optional)

Connector

RJ45

Baud Rate

Up to 115200

UMD support

Native to TSL and TSI, other third party
protocols via Apantac UIM*

Table 9: Ethernet

Network Type

Fast Ethernet 100 Base-TX

Connector

RJ45

Cable

Auto-detect. Either straight or crossed cable
will work

UMD support

Native to TSL and TSI, other third party
protocols via Apantac UIM*

*UIM – Universal Interface Module. The UIM is a small footprint router protocol translator that

acts s a bridge between the Tahoma platform of Multiviewers and other third party router, tally
and UMD protocols. The UIM can support third-party TCP/IP, UDP as well as serial protocols.
The UIM can also act as an SNMP agent for the Apantac Tahoma Multiviewers.

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 11 of 31

SPECIFICATIONS

24B!

!

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 12 of 31

Figure 1 - show the front panel of a single MiniQ.

Figure 2 - show the rear panel of a single MiniQ.

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 13 of 31

Figure 3 - show the front view of a fully configured MiniQ-3U-FR frame

Figure 4 - show the rear view of a fully configured MiniQ-3U-FR frame

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 14 of 31

25B

PRODUCT CONTENTS - “WHAT’S IN THE BOX”

!

TabLE-10: What’s in the box – MiniQ Single

Description

QTY

1

MiniQ Module

1

2

MiniQ Module Top cover

1

3

Serial Breakout

1

4

GPI Breakout

1 5 CD

1

6

RJ45 to HDMI cable

1

7

HDMI to DVI adapter

1 8 t-link cable for cascading

1

9

Terminal block for GPI

1

10

DC Power Supply

Optional

11

1 RU Rack Mount

Optional

Table 11: What’s in the box – MiniQ mouted in MiniQ-3U-FR

Description

QTY

1

MiniQ Modules

Up to 8

2

Serial Breakout

1 per MiniQ module

3

Rack mount

1 set of Rack Ears

4

GPI Breakout

1 per MiniQ module

5

Power Supplies

2 6 RJ45 to HDMI cable

1 per MiniQ module

7

t-link cable for cascading

1 per MiniQ module

8

HDMI to DVI adapter

1 per MiniQ module

9

Terminal block for GPI

1 per MiniQ module

10

CD

1

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 15 of 31

INSTALLATION

Mechanical Installation:

MiniQ can be installed in a standard 19” rack using the proper screws and washers (not
included). Tahoma modules are shipped with rack ear. These accessories are not installed to
ensure proper shipment. First locate them in the accessories box and then install them.

Note:

The MiniQs airflow is from front to back.

Figure 5 - Rack mount and airflow for Tahoma MiniQ

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 16 of 31

Default IP addresses

• When MiniQ is delivered as a single unit, the default IP address is set to 192.168.1.151

• When MiniQ is delivered in the 3 RU frame, the default IP address is set to

192.168.1.151 ~ 158, from right to left (facing the front)

IP Hub/Switch

Cascading between MiniQ’s

Figure 6 - Cascading and IP addresses of multiple MiniQ’s in a MiniQ-3U-FR

Direction of Cascading – Right to Left

.158 .157 .156 .155 .154 .153 .152 .151

192.168.1.

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 17 of 31

Power Connection:!

The single MiniQ has 2 DC power connectors to provide redundancy. The optional DC power
supplies are Universal power supplies for 90 V to 250V operation.

The MiniQ-3U-FR has 2 hot swappable AC power supplies. They are universal power supplies
for 90V to 250V operation

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 18 of 31

12B

OPERATION

UPowering Up

There is no power switch on the Tahoma Multiviewers. Plugging in the power cord will turn on
the Multiviewer. Unplugging the power cord will turn off the Multiviewer.

UConnection / Indicator / Button Descriptions

• BNC connectors for auto-detect video inputs

• 16 embedded audio meters per SDI inputs

• 8 GPI/O on the control board for alarms and recalling presets

• 8 GPI/O on the video processing board for tally, alarm and recalling presets

• 1 Ethernet connection for control and configuration

• 1 RJ45 input for serial connection

• 1 phoenix on the rear panel for line Level analog audio monitoring

• 1 RJ45 for DVI/HDMI(1.2/1.3)/VGA outputs with built in extenders to reach 35 meters (115

feet)

• LED for power status. One LED per power supply

13B

Optional Hardware

• RJ45 to VGA Receiver

• HDMI-1-R for HDMI extension

• DVI-1-LR for DVI extension

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 19 of 31

14B

MiniQ MULTIVIEWER SETUP EXAMPLES

Figure 7 - Single MiniQ modules installation with Ethernet connection.

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 20 of 31

Figure 8 - Multiple MiniQ Modules installation with a MiniQ-1U-FR rackmount.

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 21 of 31

Figure 9 - A fully configured MiniQ in a MiniQ-3U-FR frame setup. Using t-Link to cascade multiple
modules together to form a 2 x 16 setup

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 22 of 31

Figure 10 - A fully configured MiniQ in a MiniQ-3U-FR frame setup. Using t-Link to cascade multiple
modules together to form a 4 x 8 setup

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 23 of 31

Figure 11 - A fully configured MiniQ in a MiniQ-3U-FR frame setup. Using t-Link to cascade multiple
modules together to form a 8 x 14 setup

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 24 of 31

15B

ACCESSORIES

30BStandard Accessories:

Power cord (North American
customers only)

GPI breakout (on control board) –
RJ50 to DB9

Rack mount

RJ45-DB9 converter for RS232 serial
connection

Terminal Block

CD, manual

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 25 of 31

16

APPENDIX A: CONNECTORS

!

UBNC Inputs:

• 4 X BNC Connector

• Auto Detection for SDI and CVBS signal

Figure 12 -75 ohm BNC Connector

UHDMI / DVI RJ45 Output Connector:

• 3 differential pairs for data

• 1 differential pair for clock

• Total 8 pins

Figure 13 - RJ45 connector

Pin #

1 2 3 4 5 6 7

8

Function

Clk+

Clk-

Data 2+

Data 1-

Data 1+

Data 2-

Data 0+

Data 0-

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 26 of 31

HDMI / DVI Input Connector

Pin #

1 2 3 4 5 6 7

8

Function

Clk+

Clk-

Data 2+

Data 1-

Data 1+

Data 2-

Data 0+

Data 0-

U!

VGA RJ45 Connector:

• 3 for RGB

• 1 for HS

• 1 for VS

• Others are GND

• Total 8 pins

Pin #

1 2 3 4 5 6 7

8
Function

VS

HS

BLUE

GND

GREEN

GND

RED

GND

U!

RS232 RJ45 Connector:

• 1 pin for Tx

• 1 pin for Rx

• 3 pins for 5V power

• 3 pins for GND

Pin #

1 2 3 4 5 6 7

8

Function

5V

GND

Tx

GND

Rx

GND

5v

5v

U GPI I/O:

• RJ50 defined GPI I/O

• 8 pins GPI I/O

• 1 power alarm

• 1 GND

Pin #

1 2 3 4 5 6 7 8 9

10

Function

GPI
I/O
#1

GPI
I/O
#2

GPI
I/O
#3

GPI
I/O
#4

GPI
I/O
#5

GPI
I/O
#6

GPI
I/O
#7

GPI
I/O
#8

Power
Alarm

GND

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 27 of 31

Figure 14 - RJ50 to DB9 cable

Figure 15 - GPI-IN Wiring diagram. Connect this terminal block

to the RJ50 to DB9 cable shown in Figure 14.

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 28 of 31

Figure 16 - GPI-OUT Wiring diagram. Connect this terminal block

to the RJ50 to DB9 cable shown in Figure 33. Note: All LED are

standard LEDs, all resistors are 150 ohms

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 29 of 31

17B

APPENDIX B: External DC POWER SUPPLIES

• Input: Universal 100-240 VAC / 47-63 HZ input, without any slide switcher output: 12V /
0~5A

• Case Dimension: 120L X 60W X 38 H MM

• Efficiency: 78% is typical

• Safety: UL/CUL/GS/PSE/BSMI

• EMI: FCC/CE Class B, conduction and radiation has been met.

• High frequency design, less power consumption

• CEC law (energy efficiency) has been met

• Over voltage protection, short circuit protection

UInput:

Voltage

Range: Universal 100-200 VAC, single- phase
Nominal: 100–120 VAC / 200-24-VAC

Frequency

47 – 63Hz

Current

1.5A Max

Inrush Current

30A Max/100VAC; 60A Max / 240VAC

Efficiency

78% minimum 9At normal line voltage, full Load)

UDC Output:

Voltage

12.00V

Current

5A MAX

Regulation

Vo+-5%

Ripple- and Noise

200 mV Max

Total Power

60 W Max

UProtection:

Over Voltage Protection

V out (110% - 140%)

Short Circuit Protection

Automatic recovery after short circuit fault
removed

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 30 of 31

UOperating and Environmental Performance:

Temperature Range

Operating

0 OC~C +40 OC

Storage

~ 20 OC~C +60 OC

Humidity Range (non-condensing)

Operating

OPERATING

20%~ 80% RH

Storage

STORAGE

10%~ 90% RH

Cooling should operate without fan
MTBF: 50000 HOURS Min: 25OC FULL LOAD

MECHANICAL

WEIGHT: 320g
CABLX- TYPE UL 1185 18AWG
WIRE + PLUG BLACK
PLUG: 5.5 X 2.5 X 10 mm

Lock Ring to secure connection
CABLX- LX-NGTH: 150 cm
CASE DIMENSION: 120 mm(L) x 60mm(W) x 38mm(H)
EXTERNAL LOOK:

MATERIAL FLAMMABILITY: UL 94V-0

!
!

B!
!

! !

APANTAC, LLC. ● 7556 SW BRIDGEPORT ROAD ● PORTLAND, OR 97224, USA

PHONE [phone] ● FAX [phone] ● [e-mail] ● WWW.APANTAC.COM

Page 31 of 31

18B

CONTACT APANTAC

For troubleshooting, support and service, as well as upgrades, please contact:
Phone: [phone]
Email: [e-mail]

Apantac
7556 SW Bridgeport Road
Portland, OR 97224
USA
Phone: [phone]
Fax: [phone]
Email: [e-mail]

HUwww.apantac.comU