HDMI-8x8
HDMI CLEAN SWITCH
Model: CLN-SW-6x1-H
USER MANUAL
Last Updated: May 20, 2014
PHONE +1 503 986 3000 ● FAX +1 503 389 7921
APANTAC LLC ● 7470 SW Bridgeport Road, Portland, OR 97224 USA
●
INFO@APANTAC.COM
● WWW.APANTAC.COM
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
Copyright and Trademarks:
All rights reserved by APANTAC LLC, Portland, Oregon, USA. No part of this document
may be reproduced in any form or by any means without written permission from the
product manufacturer. Changes are periodically made to the information in this document.
They will be incorporated in subsequent editions. The product manufacturer may make
improvements and /or changes to the product described in this document at any time.
All the registered trademarks referred to this manual belong to their respective
companies.
PHONE +1 503 986 3000 ● FAX +1 503 389 7921 ● INFO@APANTAC.COM
APANTAC LLC
● 7470 SW Bridgeport Road, Portland, OR 97224 USA
1
● WWW.APANTAC.COM
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
Table of Contents
1.0 What’s In The Box? ............................................................................. 3
2.0 Features ............................................................................................. 4
3.0 Specifications ..................................... .............................................. ... 5
4.0 Front/Rear Panels ................................................................................ 5
4.0.1: Front Panel ......................................................................................... 5
4.0.2 Button Descriptions ............................................................................. 6
4.0.3: Rear Panel .......................................................................................... 7
5.0 Remote Communications ............................. .................................... ..... 9
5.0.1 Switch Control Connection.................................................................... 9
5.0.2 IR Connection ................................................................................... 13
PHONE +1 503 986 3000 ● FAX +1 503 389 7921 ● INFO@APANTAC.COM
APANTAC LLC
● 7470 SW Bridgeport Road, Portland, OR 97224 USA
2
● WWW.APANTAC.COM
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
1.0 What’s In The Box?
HDMI Clean Switch, Model: CLN-SW-6x1-H
RS232 Communication Connecting Cable
Power Cord
Power Adapter
HDMI Cable
Remote Control
User Manual
HDMI Matrix Software CD
Rack Ear Screws
2 Rack-Mount Brackets
3
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
2.0 Features
Up/down/cross converter equipped with HDMI input/output
HDTV resolution up to 1080P
Compliant with the specifications of HDMI
7 built-in presets (1 x full screen, 4 x PIP mode, 2 x PBP mode)
Supports adjustable audio delay time for lip-sync (up to 70 ms)
Supports 2 aspect ratio modes
• 1:1 Aspect ratio mode: Keeps original input source aspect size and ratio
• Full Screen Aspect ratio mode: This mode modifies the original input image
to fit the aspect ratio of the output display. Image may be cropped or
distorted to fit within the screen of the output display.
Supports 8 different output resolutions:
VGA, 480P, SVGA, XGA, 720P, SXGA, UXGA, 1080P
Supports “Audio Delay” adjustment for lip sync
Supports both HDMI and VGA output
Supports RS232 control.
Supports Ethernet control
Hot pluggable and 1RU rack design
EDID management (copy from destination port)
PHONE +1 503 986 3000 ● FAX +1 503 389 7921 ● INFO@APANTAC.COM
APANTAC LLC
● 7470 SW Bridgeport Road, Portland, OR 97224 USA
● WWW.APANTAC.COM
4
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
3.0 Specifications
FUNCTION CLN-SW-6x1-H
INPUT CONNECTOR 6 x HDMI Type A Female
OUTPUT CONNECTOR
1 x HDMI Type A
1 x VGA HD15
RS232 CONNECTOR DB9 Female
LAN CONNECTOR RJ45
AUDIO OUT 1 x 35mm phone jack
DIP SWITCH 1 x 8 positions
POWER 100 ~240 VAC, 12V 5A DC Adapter
SIZE 1RU, 384x173x 45 mm
WEIGHT 1.8kg
MAXIMUM RESOLUTION 1080P 60Hz
MAXIMUM PIXEL CLOCK 225MHz
HDMI CABLE DISTANCE 10 meters (33 feet)
IR remote
CONTROL
RS232
Ethernet via Web
4.0 Front/Rear Panels
4.0.1: Front Panel
Figure 4-1: CLN-SW-6x1-H Front Panel
PHONE +1 503 986 3000 ● FAX +1 503 389 7921 ● INFO@APANTAC.COM
APANTAC LLC
● 7470 SW Bridgeport Road, Portland, OR 97224 USA
● WWW.APANTAC.COM
5
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
4.0.2 Button Descriptions
• A 1 ~ 6: Input selection for the 6 primary inputs
• B 1 ~ 6: Input selection for the 6 secondary inputs
• A/B: Audio selection for input A or B
• Audio Delay: Audio delay adjustment for lip sync up to 70 ms
• Aspect Ratio:
Full Screen: Will match the image to the display aspect ratio
1:1: Will retain the original input aspect ratio
• Resolutions
VGA, 480P, SVGA, XGA, 720P, SXGA, UXGA, 1080P
• Presets: Presets 1 to 6.
7 is reserved.
PHONE +1 503 986 3000 ● FAX +1 503 389 7921 ● INFO@APANTAC.COM
APANTAC LLC
● 7470 SW Bridgeport Road, Portland, OR 97224 USA
6
● WWW.APANTAC.COM
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
4.0.3: Rear Panel
1. Power: 12V DC 3A
2. HDMI 1 ~ 6: 6 HDMI inputs
HDMI Type A Connector Pin Definition:
Pin # Signal Pin # Signal
1 TMDS Data2+ 11 TMDS Clock Shield
2 TMDS Data2 Shield 12 TMDS Clock-
3 TMDS Data2- 13 NC
Figure 4-2: CLN-SW-6x1-H Rear Panel
4 TMDS Data1+ 14 NC
5 TMDS Data1 Shield 15 DDC-SCL
6 TMDS Data1- 16 DDC-SDA
7 TMDS Data0+ 17 DDC-Ground
TMDS Data0
8
18 +5V Power
Shield
9 TMDS Data0- 19 Hot Plug Detect
10 TMDS Clock+
3. HDMI out: HDMI output
4. VGA out: VGA copy of HDMI out
5. Audio out: Analog audio monitoring output. Follows video output
6. RS232
7. IR: Connection to the IR Blaster
8. DIP Switch:
7
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
Figure 4-3: DIP Switch
• DIP Switcher Pin 1: Reset the web server IP address to 192.168.0.3. The
steps are as below:
o Please adjust the pin1 to ON and re-start the CLN-SW-6x1-H Switcher
o After the HRM-602P Switcher re-starts about 10 seconds, shut down your
equipment.
o For a normal operation, please adjust the pin1 to OFF, then power on the
HRM-602P Switcher again. The IP address will be restored to the default
value: 192.168.0.3
• DIP Switcher Pin 2 to 3: Switch between RS232 port and LAN port connection.
SW3 SW2
LAN ON ON
RS232 ON OFF
•
DIP Switcher Pin 4 to 8: Down position is “ON” (0), the up position is “OFF” (1)
PHONE +1 503 986 3000 ● FAX +1 503 389 7921 ● INFO@APANTAC.COM
APANTAC LLC
● 7470 SW Bridgeport Road, Portland, OR 97224 USA
8
● WWW.APANTAC.COM
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
9. HDMI 1 ~ 6: HDMI/DVI monitors or projectors
HDMI Type A Connector Pin Definition:
Pin # Signal Pin # Signal
1 TMDS Data2+ 11 TMDS Clock Shield
2 TMDS Data2 Shield 12 TMDS Clock-
3 TMDS Data2- 13 NC
4 TMDS Data1+ 14 NC
5 TMDS Data1 Shield 15 DDC-SCL
6 TMDS Data1- 16 DDC-SDA
7 TMDS Data0+ 17 DDC-Ground
8
18 +5V Power
Shield
9 TMDS Data0- 19 Hot Plug Detect
10 TMDS Clock+
5.0 Remote Communications
5.0.1 Switch Control Connection
Use the supplied RS232 cable to connect the computer’s serial port (COM1
or COM2) to the RS232 port of the CLN-SW-6x1-H to enable remote control
via serial interface.
TMDS Data0
Figure 5-1 (a): RS232 and Control PC connection
CLN-SW-6x1-H also supports a LAN port that allows you to control the
switch through a browser.
PHONE +1 503 986 3000 ● FAX +1 503 389 7921 ● INFO@APANTAC.COM
APANTAC LLC
● 7470 SW Bridgeport Road, Portland, OR 97224 USA
● WWW.APANTAC.COM
9
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
Figure 5-2 (b): LAN port and Control PC Connection
PHONE +1 503 986 3000 ● FAX +1 503 389 7921 ● INFO@APANTAC.COM
APANTAC LLC
● 7470 SW Bridgeport Road, Portland, OR 97224 USA
10
● WWW.APANTAC.COM
RS232 Pin out
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
Pin No. Leg Description
1 N/u Null
2 Tx Send
3 Rx Receive
4 N/u Null
5 Gnd Ground
6 N/u Null
7 N/u Null
8 N/u Null
9 N/u Null
Figure 5-3
Figure 5-3 (a)
11
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
Figure 5-3 (b)
12
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
5.0.2 IR Connection
The CLN-SW-6x1-H can also be controlled via an IR remote control simply
by connecting the IR port on the rear panel.
Figure 5-4: IR Connection
The CLN-SW-6x1-H supports a remote controller, which allows remote switching with an
IR remote control.
Figure 5-5: Remote Control
13
HDMI CLEAN SWITCH – MODEL: CLN-SW-6x1-H
Channel A Selection:
Press the Number#1~6 button to select the inputs on Channel A.
Channel B selection:
Press the “0” + Number#1~6 button to select the inputs on Channel B.
Example: Press the “0” on the Remote first, then press the “3” to select input 3 on
channel B. Channel B is only available in PIP modes (1 ~ 7).
14
Loading...