A.O. Smith QOS1237 Specifcations

Storage Tanks

®

CUSTOM-LINE FACTORY JACKETED AND
INSULATED STORAGE TANKS

Large volume tanks are designed for storing potable water. Fitting locations
of these custom-line tanks match the needs of normal installations plus those
for the A. O. Smith Cer-Temp®80 and Shure-Temp™ systems.

FEATURES

STANDARD SIZES FROM 140 TO 1,000 GALLONS A. O. Smith stocks vertical

factory jacketed and insulated tanks from 140 gallons up to 1,000 gallons for
fast delivery and retrofit applications. All stock tanks are glasslined with
standard tank openings as shown on following pages. For custom or larger
capacities, see our custom line tanks or consult your factory representatives.

ASME CODE CONSTRUCTION - All tanks are constructed to the requirements of
the ASME. ASME code tanks are available in 100, 125, 150 and 160 psi working pressures
(125 psi working pressure - standard)
or lesser working pressures, with special configurations or materials.

INSULATION - Entire tank is surrounded with high density fiber
glass insulation to reduce costly heat loss; non-sagging and
vermin-proof. To meet ASHRAE 90.1 (current edition) depth of
insulation cavity requires use of remote bulb-type tank
temperature control and thermometer. Storage tanks meet
R12.5 minimum thermal insulation requirements of the
U.S. Department of Energy and current edition of
ASHRAE/IESNA 90.1.

. Consult factory for ASME

code tanks with greater

MODELS

AND

TJV

TJH

CABINET

provides additional insulating qualities for greater energy savings.

LININGS AND COATINGS - Each lining and coating has
particular capabilities and limitations. Please consult the
factory for recommendations on the uses of linings for specific applications.
Thorough investigation on the service life of steel tanks with protective coatings
or linings has led to the recommendations of the following linings:

CATHODIC PROTECTION - Glasslined, cement and epoxy tanks are furnished with
anodes designed for maximum protection.

ACCESSORIES - Tanks will be supplied with the fittings located
as indicated on the drawings unless specified otherwise. A
manhole or handhole is included on cement or epoxy tanks.

A manhole or handhole is optional on glasslined tanks.

- Heavy gauge steel with high quality powder coat paint

Glasslined (Standard) - These are normally stocked tanks for water storage up to 180 F,
with glass lining to prevent corrosion and addition of rust to water. The glass lining was
developed over many years of ceramic research for a wide variety of conditions.

Cement - A special formulation of cement provides excellent corrosion protection. Available
on 200 gallon and larger sizes. A manhole or handhole is included for application of cement lining.

Epoxy - The application of specially formulated epoxy makes this lining suitable for cold or hot
water storage. A manhole or handhole is included for application of epoxy lining. Available on 200
gallon and larger sizes.

Low Lead Content

U

OPTIONAL

CRN

Revised November 2012

Page 1 of 4

AOSTT35200

®

Storage Tanks

STORAGE TANK SELECTION

TJV-140 THRU TJV-1000

FIGURE 1.

NOTE: Inspection openings, i.e., handholes and manholes, are optional and are to be included with glasslined tanks

only when specified. Tanks so equipped are f.o.b. Seattle.

Other tanks to 66” diameter and 3500 gallon are available on special order.

All openings Female Pipe Thread except as noted.

“F” opening Male Pipe Thread.

MODEL AND

GALLON

CAPACITY A B C D E F G H

TJV-140 87 30 21 1/2 51 8 1 1/2 2 1/2 6 3/8

TJV-200 83 36 22 45 10 1 1/2 2 1/2 7 3/4

TJV-250 96 36 22 58 10 1 1/2 2 1/2 7 3/4

TJV-350 97 42 24 1/2 54 14 1 1/2 2 1/2 9 1/2

TJV-400 105 42 24 1/2 61 14 1 1/2 2 1/2 9 1/2

TJVT-500 100 48 27 52 16 1 1/2 3 11 5/16

TJV-500 84 54 27 3/4 33 1/4 18 1 1/2 3 12 3/4

TJV-750 116 54 27 3/4 65 1/2 18 1 1/2 3 12 3/4

TJV-1000 150 54 27 3/4 97 1/2 18 1 1/2 3 12 3/4

www.hotwater.com

Page 2 of 4

AOSTT35200