THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY
REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL;
WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF
PUBLICA TION AND DISCLAIMS RELIABILITY FOR CHANGES, ERRORS OR OMISSIONS.
MANUFACTURE DATA: Jan-03-05
HP VS17 Service Manual
Table of Contents
Table of Contents ---------------------------------------------------------------------------------- 02
Revision List --------------------------------------------------------------------------------------- 04
43.2cm (17”) a-si TFT Active matrix LCD panel, 0.264mm dot pitch
Scalar chipset: ADE3800SXL/TSU16AK
Microprocessor controlled scan technology
15 factory presets, 10 user modes
Vertical refresh rate 50Hz to 76Hz; Horizontal frequency 30kHz to 83kHz
Resolutions: 1280x1024/75Hz
Power Internal AC100V-240V
Tilt -5° to 30°
CE mark
TCO 03 mark
VESA DPMS compliant
VESA DDC2B compliant and DDC/CI interface.
2. LCD Monitor Description
The LCD Monitor will contain main board,power board, key board, Audio board and which house
the flat panel control logic, brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the
main board chips each voltage.
Power Board
Monitor Block Diagram
CCFT Drive.
Main Board
Audio board
Flat Panel and
CCFL backlight
Keyboard
RS232 Connector
For white balance
adjustment in
factory mode
AC-IN
100V-240V
HOST Computer
Video signal, DDC
5
HP VS17 Service Manual
3. Operation Instructions
3.1 General Instructions
The control buttons are located at the left side of monitor , and press the power button to turn the
monitor on or off. By changing these settings, the picture can be adjusted to your personal
performance.
The power cord should be connected and insert to adaptor.
-
Connect the video cable from the monitor to the computer VGA card.
-
- Press the power button to turn on the monitor, the power indicator will light up to Green.
3.2 Control Buttons
6
HP VS17 Service Manual
7
3.3 Adjust the Picture
HP VS17 Service Manual
8
HP VS17 Service Manual
r
1.
2.
3.
4.
5.
6.
7.
Brightness
Contrast Adjust the contrast
Image
Control
Volume Adjust the volume
Color
Language Shows the language of the OSD window.
Management
Adjust the brightness.
Adjust the:
z Auto Adjustment: Adjusts the main settings and produces a stable,
centered image.
z H-Position: horizontal position of the screen image.
z V-Position: vertical position of the screen image.
z Clock: frequency of the pixel clock to minimize vertical bar.
z Phase: phase value to minimize horizontal jitters.
z 9300K: recall 9300K colo
z 6500K: recall 6500K color
z SRGB: recall SRGB color
z Custom Color: adjust s the color tint of white, and the red, green, and
blue (RGB) mix for colors.
z Power Saver: enable/disable power saving
z Power On Recall: enable/disable power recall
z Mode Display: enable/disable mode display
z Sleep Timer: set sleep timer
z Basic Menu: set to basic menu
8.
9.
10.
11.
OSD Control
Information
Factory
Reset
Exit Exit the current OSD window.
OSD (on Screen Display) settings: adjusts the H/V position, timeout, On
Screen Display window.
Current setting, recommended setting, serial number, total hours,
backlight hours, Exit.
Resets the display to original factory settings for color, brightness,
phase, and clock.
9
4. Input/Output Specification
4.1 Input Signal Connector
PIN MNEMONICSIGNAL
1 RV Red Video
2 GV Green Video
3 BV Blue Video
HP VS17 Service Manual
4 NC
5 GND Ground (DDC Return)
6 RG Red GND
7 GG Green GND
8 BG Blue GND
9 +5 V +5 V (from PC)
10 SG Sync Ground
11 NC None
12 SDA DDC Data
13 HS Horizontal Sync
14 VS Vertical Sync
15 SCL DDC Clock
PC Connect detection
VGA connector layout
PIN 1
PIN 5
PIN 11
10
4.2 Factory Preset Display Modes
HP VS17 Service Manual
Preset Pixel Format
Horz Freq
(KHz)
1 640 x 480 31.5 60.0
2 640 x 480 37.9 72.0
3 640 x 480 37.5 75.0
4 720 x 400 31.5 70.0
5 800 x 600 37.9 60.0
6 800 x 600 48.1 72.0
7 800 x 600 46.9 75.0
8 832 x 624 49.7 75.0
9 1024 x 768 48.4 60.0
10 1024 x 768 56.5 70.0
11 1024 x 768 60.0 75.0
12 1152 x 870 68.7 75.6
13 1152 x 900 71.7 76.0
14 1280 x1024 63.9 60.0
Vert Freq
(Hz)
15 1280 x1024 80.0 75.0
4.3 Power Supply Requirements
PARAMETER RANGE
AC Input Voltage 90 to 265V
AC Input Frequency 47 to 63 Hz
Inrush Current 50A MAX AT 220VAC
Power consumption <=37W
Leakage Current < 500 micro amps at an input of 120 Volts AC.
11
5. Panel Specification
5.1 General Feature
HP VS17 Service Manual
12
5.2 Optical Characteristics
SAMSUNG LTM170EU-L11
HP VS17 Service Manual
13
LG LM170 E1-A5KE
HP VS17 Service Manual
14
6. Block Diagram
6.1 Monitor Exploded
HP VS17 Service Manual
15
HP VS17 Service Manual
2510
1276
4
3
8
91411
13
1
16
1
19
18
6.2 Software Flow Chart
1
1) MCU initialize.
2) Is the eeprom blank?
3) Program the eeprom by default
values.
4) Get the PWM value of brightness from
eeprom. Check the pin PANEL1 and
PANEL2 to tell which panel to get with it.
5) Is the power key pressed?
6) Clear all global flags.
7) Are the AUTO and SELECT keys
pressed?
8) Enter factory mode.
9) Saving the power key status into
eeprom. Turn on the LED a nd set it to
green color. Scalar initializes. In standby
mode?
Update the lifetime of back light.
10) Check the analog and digital port, are
there any signals coming?
11) Does the scalar send out an interrupt
request?
12) Wake up the scalar.
13) Are there any signals coming from
analog or digital port?
Display " No Input Signal " message.
And go into standby mode after the
message disappear.
14) Program the scalar to be able to show
the coming mode.