SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERV ICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
Page 2
Revision List
Version Release Date Revision History L&T Model Name
TIBJT32CB7SUHNF.LF
A00 Jun-5-2012 Initial Release
A01 AUG-20-2012 Add new models
TIBJT32KB7A1HNF.LF
TIBJT32CB7JBHNF.LF
TIBJT32EB7RMHNF.LF
TIBJT32EB7SPHNF.LF
2
Page 3
Important Safety Notice
Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The servi ce
procedures recommended by AOC and described in this service manual are effective methods of performin g service
operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIO NS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC mu st first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specifie d safet y charact erist ics may create sho ck,
fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
FOR PRODUCTS CONTAINING LASER:
DANGER-Invisible laser radiation when open AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is ground ed through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)
3
Page 4
1. Monitor Specifications
4
Page 5
2. LCD Monitor Description
The LCD MONITOR will contain a main board and a key board which house the flat panel control logic, brightness
control logic and DDC.
Monitor Block Diagram
LED Drive.
Flat Panel and
LED backlight
Main Board
Key Board
Adapter
D-SUB
Signal
DVI
Signal
AC-IN
100V~240V
5
Page 6
3. Operating Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor.
By changing these settings, the picture can be adjusted to your personal preferences.
3.2 Hotkeys
Power
Press the Power button to turn on/off the monitor.
Menu/Enter
Press to display the OSD or confirm the selection
Eco (DCR)/-
Press the Eco key continuously to select the Eco mode of brightness and DCR on when there is no OSD. (Eco mode hot key may
not be available in all models).
4:3 or Wide/+
When there is no OSD, press > continuously to change 4:3 or wide image ratio. (If the product screen size is 4:3 or input signal
resolution is wide format, the hot key is disabled to adjust.)
Source/Auto / Exit
Auto / Exit
When the OSD is closed, press Auto/Source/Exit button continuously about 2 second to do auto configure (only for the models
with dual or more inputs).
When the OSD is closed, press Auto/Source/Exit button will be Source hot key function (Only for the models with dual or more
inputs).
6
Page 7
3.3 OSD Setting
Basic and simple instruction on the control keys.
1) Press theMENU-button to activate the OSD window.
2) Press < or > to navigate through the functions. Once the desired function is highlighted, press the
MENU-button to activate sub-menu . Once the desired function is highlighted, press
it.
3)
Press or to change the settings of the selected function. Press AUTO to exit. If you want to
adjust any other function, repeat steps 2-3.
4) OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then
press
the monitor is off and then press
Notes:
1) If the product has only one signal input, the item of "Input Select" is disable to adjust.
2) If the product screen size is 4:3 or input signal resolution is wide format, the item of "Image Ratio" is disable to
adjust.
3) One of DCR, Color Boost, and Picture Boost functions is active, the other two function is turned off accordingly.
power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while
power button to turn the monitor on.
MENU-button to activate
7
Page 8
Luminance
1
Press
(Menu) to display menu
2
Press or to select (Luminance), an d press to enter
3
Press or to select submenu, and press to enter.
8
Page 9
4
Press or to adjust
5
Press to exit.
9
Page 10
Image Setup
1
Press (Menu) to display menu
2
Press or to select (Image Setup) , and press to enter.
3
Press or to select submenu, and press to enter.
4
Press or to adjust.
10
Page 11
5
Press to exit.
Color Setup
1
Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise.
Phase 0-100 Adjust Picture Phase to reduce Horizontal-Line noise
Sharpness 0-100 Adjust picture sharpness
H.Position0-100 Adjust the horizontal position of the picture.
V.Position0-100 Adjust the vertical position of the picture.
Press (Menu) to display menu.
2
Press or to select (Color Setup), and press to enter.
11
Page 12
3
Press or to select submenu, and press to enter.
4
Press
or to adjust.
5
Press to exit.
12
Page 13
Warm Recall Warm Color Temperature from EEPROM.
Normal Recall Normal Color Temperature from EEPROM.
Cool Recall Cool Color Temperature from EEPROM.
Color setup.
DCB Mode
DCB Demo on or off Disable or Enable Demo
Picture Boost
1
sRGB Recall SRGB Color Temperature from EEPROM.
Red Red Gain from Digital-register
User
Green Green Gain Digital-register.
Blue Blue Gain from Digital-register
Full
on or off Disable or Enable Full Enhance Mode
Enhance
Nature Skin on or off Disable or Enable Nature Skin Mode
Green Field on or off Disable or Enable Green Field Mode
Sky-blue on or off Disable or Enable Sky-blue Mode
AutoDetect on or off Disable or Enable AutoDetect Mode
Press (Menu) to display menu.
2
Press or to select (Picture Boost), and press to enter.
3
13
Page 14
Press or to select submenu, and press to enter.
4
Press or to adjust.
5
Press to exit.
Frame Size 14-100 Adjust Frame Size
Brightness 0-100 Adjust Frame Brightness
Contras 0-100 Adjust Frame Contrast
H. position 0-100 Adjust Frame horizontal Position
V.position 0-100 Adjust Frame vertical Position
Bright Frame on or off Disable or Enable Bright Frame
14
Page 15
OSD Setup
1
Press (Menu) to display menu.
2
Press or to select (OSD Setup), and press to enter.
3
Press or to select submenu, and press to enter.
15
Page 16
4
Press or to adjust.
5
Press to exit.
H.Position 0-100 Adjust the horizontal position of OSD
V.Position 0-100 Adjust the vertical position of OSD
Timeout 5-120 Adjust the OSD Timeout
Transparence 0-100 Adjust the transparence of OSD
Language Select the OSD language
Extra
1
Press (Menu) to display menu.
16
Page 17
2
Press or to select (Extra), and press to enter.
3
Press or to select submenu, and press to enter.
4
Press or to adjust.
5
Press
to exit.
17
Page 18
Exit
1
Press (Menu) to display menu.
2
Press or to select (Exit), and press to exit.
Exit Exit the main OSD
18
Page 19
19
Page 20
4. Input/Output Specification
4.1 D-SUB CONNECTORS
Pin Assignments
Pin Number
1
2
3
4 N.C. 12 DDC- Serial data
5
6 GND-R 14 V- sync
7 GND-G 15 DDC- Serial clock
8 GND-B
15-Pin Side of the Signal Cable
Video-Red
Video-Green
Video-Blue
Detect Cable
Pin Number 15-Pin Side of the Signal Cable
9 +5V
10
11 N.C.
13 H-
Ground
sync
20
Page 21
4.2 Factory Preset Display Modes
21
Page 22
4.3 Panel Specification
4.3.1 General Features
BM215WF4-T2BB is a Color Active Matrix Liquid Crystal Display with an integral Light Emitting Diode (LED)
backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type
display operating in the normally white mode. It has a 21.5 inch diagonally measured active display area with Full
HD resolution (1080 vertical by 1920 horizontal pixel array) Each pixel is divided into Red, Green and Blue
sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is
determined with a 8-bit gray scale signal for each dot, thus, presenting a palette of more than 16,7M colors with
Advanced-FRC(Frame Rate Control). It has been designed to apply the interface method that enables low power,
high speed, low EMI. FPD Link or compatible must be used as a LVDS(Low Voltage Differential Signaling) chip. It is
intended to support applications where thin thickness, wide viewing angle, low power are critical factors and graphic
displays are important. In combination with the vertical arrangement of the sub-pixels, the BM215WF4-T2BB
characteristics provide an excellent flat panel display for office auto mation products such as monitors.
4.3.2 Display Characteristics
22
Page 23
4.3.3 Electrical Characteristics
Parameter Symbol
Ta = 25°C
Values
Unit Notes
Min Typ Max
MODULE :
Power Supply Input V oltage V
Permissive Power Input Ripple V
I
Power Supply Input Current
Power Consumption P
Inrush current I
LED bar Electrical characteristics
Parameter Symbol Condition
LED : 1,7
LCD
LCD
LCD-MOSAIC
I
LCD-BLACK
I
LCD-BLACK
LCD
RUSH
4.5 5.0 5.5 Vdc
- - 0.3 V 3
(60Hz)
- 1000 1300 mA 1,5
(60Hz) - 1300 1690 mA 2,5
(75Hz) - 2000 mA 5
- 5.00 6.5 Watt 1
- - 3.0 A 1, 4
Values
Unit Notes
Min. Typ. Max.
LED String Current Is - 110 120 mA 2,7
LED String Voltage Vs 48.0 51.2 54.4 V 3,7
It is suitable for 18.5", 20",21.5'' & 23" LED panel
215W
6.2K
270K
0.12 ohm
NC
230W
6.2K
39K
0.2 ohm
0.2 ohm
R809
R834
R812
R816
190W
6.2K
NC
0.15 ohm
NC
200W
6.8K
270K
0.15 ohm
NC
30
T P V ( Top Victory Elec tronics C o . , Ltd. )
絬 隔 瓜 絪 腹
Key Component
715G4798-M0A-000-0040_101101
CONVERT
Date
OEM MODEL
TPV MODEL
PCB NA ME
Sheet
CONN
AOC 50ID
AOC 50IDC
88Thursday , May 12, 2011
of
Size
Rev
称爹
Custom
<
称爹
>
Page 31
6.2 Key Board
715G4842K0E000004F
CIN_01
GPIO_00
CIN_03
GPIO_01
V3.3
TP2
KEY0.1524
C007
100nF 25V
AC_SHIELD
VBIAS
R004
100R 1/16W 5%
C008
100P 50V
D001
Blue
CIN_05
CIN_07
CIN_09
CIN_11
Orange
U001
IT7230EFN/ BX
5V_LED
1
2
3
1
CIN03
2
CIN07
3
CIN09
4
CIN11
14
17
16
CIN0015CIN01
E-PAD
VSHILD5VBIAS6AVSS7AVCC
8
V3.3
VBIAS
AC_SHIELD
R007
4K7 1/16W 5%
GPIO013GPIO1
INT#
SDA
SCLK
DVCC
C006
100nF 25V
12
SM_INT#
11
SM_DATA
10
SM_CLK
9
R008
4K7 1/16W 5%
GPIO_01
GPIO_00
V3.3
C005
100nF 25V
R001
10K 1/16W 5%
4K7 1/16W 5%
R002
C003
12P 50V
Auto
4K7 1/16W 5%
R003
C004
12P 50V
CN001
SM_CLK
5V_LED
V3.3
C011
1UF 10V
ZD001
UDZSNP5.6B
12
12
-
SM_DATA
ZD002
UDZSNP5.6B
R0050R05 1/16W
R0060R05 1/16W
Menu+
CLK
DATA
SM_INT#
Power
1
2
3
4
5
6
CABLE
CIN_03
Auto
AUTO_4
KEY0.1524
CIN_01
-
-_2 KEY0.1524
CIN_11
+
+_3
KEY0.1524
MENU_5 KEY0. 1524
MENU
CIN_07CIN_09
Power
PWR_1 KEY0.1524
絬 隔 瓜 絪 腹
Key Component
T P V ( Top Victory Electronics Co . , Ltd. )
Date
Dif f erential KEY0.1524
CIN_05
Differential
715G4164-K0C-000-0040_20100420.DSN
2.0 Touch key
OEM MOD EL
TPV MO D EL
PCB NAME
Sheet
AOC e943Fw
e943FwC
715G4164-K0C
22Tuesday , April 19 , 2011
of
Size
Rev
称爹
A3
<
称爹
>
31
Page 32
7. PCB Layout
7.1 Main Board
32
Page 33
33
Page 34
7.2 Key Board
715G4842K0E000004F
34
Page 35
8. Maintainability
8.1 Equipments and Tools Requirement
1. Voltmeter.
2. Oscilloscope.
3. Pattern Generator.
4. DDC Tool with an IBM Compatible Computer.
5. Alignment Tool.
6. LCD Color Analyzer.
7. Service Manual.
8. User Manual.
35
Page 36
8.2 Trouble Shooting
1. No Power
No power
Check power cable is
tightened?
Re-plug the power cable
OK
Check Power “On/Off”
is “On”?
Turn on the Power “On/Off” switch
OK
Check the LED
indicate is OK?
Check the AC powe r
OK
Replace main board and check connections
Replace key board and check connections
36
Page 37
2. No Video (Power LED White)
No Video (Power LED White)
Press the power
button is OK?
NG
Replace the main board
Replace the main
board and connection
OK
The end
Check the LVDS/FFC
cable or panel
OK
Replace the LVDS/FFC
cable or panel
Replace the key board
37
Page 38
q
y
3. DIM
DIM (image overlap, focus or flicker)
Reset in factory mode
OK
The end
NG
Set to the optimal
frequency, select the
recommended fre
uenc
OK
The end
NG
Readjust the phase and pixel
clock in the user mode
OK
The end
NG
Pull out signal cable and
check “Self Test Feature
Check” is ok?
OK
Check the signal cable
and the PC
NG
NG
Replace the main board
OK
The end
NG
Replace the panel
OK
38
Page 39
g
y
4. Color is not optimal
Color is not optimal
Miss color
Color shift
Replace the signal cable
OK
NG
The end
Reset the factory mode
NG
In the user mode, set the” color
settin
s” until customer satisf
Pull out the signal cable
and check the screen
color display is normal?
NG
OK
NG
Replace the signal cable or PC
Replace the main board
39
Page 40
9. White- Balance, Luminance Adjustment
Approximately 30 minutes should be allowed for warm up before proceeding white balance adjustment.
How to setting MEM channel you can reference to chroma 7120 user guide or simpl use “SC” key and “NEXT” Key
to modify xyY value and use “ID” key to modify the TEXT description Following is the procedu re to do white-bala nce
adjust .
2. Setting the color temp. you want
A. MEM.CHANNEL 3 Warm (6500K):
Warm color temp. parameter is x = 313 ±30, y = 329 ±30
B. MEM.CHANNEL 4 Normal (7300K):
Normal color temp. parameter is x = 301 ±30, y = 317 ±30
C. MEM.CHANNEL 9 Cool (9300K):
Cool color temp. parameter is x = 283 ±30, y = 297 ±30
D. MEM.CHANNEL 10 (sRGB color):
sRGB color temp. parameter is x = 313 ±30, y = 329 ±30
3. Enter into the factory mode
Turn off the powe r, press two direction keys and turn the power on. Then press the “MENU” button. The factory OSD
will appear.
4. Gain adjustment:
Move cursor to “-F-” and press MENU key
A. Adjust Warm (6500K) color-temperature
1. Switch the chroma-7120 to RGB-Mode (with press “MODE” button)
2. Switch the MEM.channel to Channel 3 (with up or down arrow on chroma 7120)
3. The LCD-indicator on chroma 7120 will show x = 313 ±30, y = 329 ±30
4. Adjust the RED on factory windo w until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN on factory windo w until chroma 7120 indicator reachedthe value G=100
6. Adjust the BLUE on factory wind ow until chroma 7120 indicator reached the value B=100
7. Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance =100±2
B. Adjust Normal (7300K) color-temperature
1. Switch the chroma-7120 to RGB-Mode (with press “MODE” button)
2. Switch the MEM.channel to Channel 4 (with up or down arrow on chroma 7120)
3. The LCD-indicator on chroma 7120 will show x = 301 ±30, y = 317 ±30
4. Adjust the RED on factory windo w until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN on factory windo w until chroma 7120 indicator reachedthe value G=100
6. Adjust the BLUE on factory wind ow until chroma 7120 indicator reached the value B=100
7. Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance =100±2
40
Page 41
C. Adjust Cool (9300K) color-temperature
1. Switch the Chroma-7120 to RGB-Mode (with press “MODE” button)
2. Switch the MEM. Channel to Channel 9 (with up or down arrow on chroma 7120)
3. The LCD-indicator on chroma 7120 will show x = 283 ±30, y = 297 ±30
4. Adjust the RED on factory windo w until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN on factory windo w until chroma 7120 indicator reached the value G=100
6. Adjust the BLUE on factory wind ow until chroma 7120 indicator reached the value B=100
7. Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance =100±2
D. Adjust sRGB color-temperature
1. Switch the chroma-7120 to RGB-Mode (with press “MODE” button)
2. Switch the MEM.channel to Channel 10 (with up or down arrow on chroma 7120)
3. The LCD-indicator on chroma 7120 will show x = 313 ±30, y = 329 ±30
4. Adjust the RED on factory windo w until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN on factory windo w until chroma 7120 indicator reachedthe value G=100
6. Adjust the BLUE on factory wind ow until chroma 7120 indicator reached the value B=100
7. Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance =100±2
E. Turn the Power-button off to quit from factory mode.
41
Page 42
10. Monitor Exploded View
42
Page 43
No. Description
1 BEZEL
2 Power lens
3 RUBBER FEET
4 Main frame
5 Rear cover
6 Hinge
7 Stand
8 Stand cover
Note: The parts information listed belo w are for reference only, and are subject to change without notice. Please go
to http://cs.tpv.com.cn/hello1.asp