Antunes, AJ MS-355, MS-250, MS-255 User Manual
MMIIRRAACCLLEE SSTTEEAAMMEERR
Models MS-150/155,
MS-250/255 & MS-355
Owner’s Manual
P/N 1010699 Rev. B
MANUFACTURING
NUMBERS:
9100420
9100426
9100428
9100430
9100436
9100438
9100450
9100456
9100458
9100460
9100462
9100466
9100468
9100480
9100486
®
C
US
MIRACLE STEAMER
1
P/N 1010699 Rev. B
A.J. Antunes & Co.
General
The Miracle Steamer produces steam using plain tap
water for quick heating and reconstituting of food items.
Simple pushbutton action delivers a fully adjustable
impulse of steam. Because the amount of steam is
consistent, it removes the guesswork and produces a
uniform finished product from one operator to the next.
This manual provides the safety, installation and operating procedures for the Miracle Steamer. We recommend that all information contained in this manual be
read prior to installing and operating the unit.
Your Miracle Steamer is manufactured from the finest
materials available and is assembled to Roundup’s
strict quality standards. This unit has been tested at
the factory to ensure dependable trouble-free operation.
Warranty Information
Please read the full text of the Limited Warranty in this
manual.
OWNER INFORMATION
Operation ...................................................................8
General ......................................................................
8
Operating Instructions ...............................................
9
Programming .............................................................
9
Steaming Tips ..........................................................
11
Hi-Limit Reset Button...............................................
11
Maintenance.............................................................12
Daily.........................................................................
12
Monthly
....................................................................12
Troubleshooting......................................................15
Replacement Parts..................................................18
Wiring Diagrams .....................................................26
Warranty....................................................Back Cover
Owner Information.....................................................1
General ......................................................................
1
Warranty Information .................................................
1
Service/Technical Assistance ....................................
2
Model Designation.....................................................
2
Important Safety Information ...................................2
Specifications ............................................................4
Electrical Ratings ......................................................
4
Electrical Cord & Plug Configurations ......................
4
Dimensions ...............................................................
5
Installation .................................................................6
Unpacking .................................................................
6
Equipment Setup ......................................................
6
TABLE OF CONTENTS
IMPORTANT! Keep these instructions for future reference. If the unit changes owner-
ship, be sure this manual accompanies the equipment.
If the unit arrives damaged, contact the carrier immediately and file a damage claim with them. Save all
packing materials when filing a claim. Freight damage
claims are the responsibility of the purchaser and are
not covered under warranty.
The warranty does not extend to:
• Damages caused in shipment or damage as
result of improper use.
• Installation of electrical service.
• Normal maintenance as outlined in this manual.
• Malfunction resulting from improper maintenance.
• Damage caused by abuse or careless handling.
• Moisture damage to electrical components.
• Damage from tampering with, removal of, or
changing any preset control or safety device.
IMPORTANT
A.J. Antunes & Co. reserves the right to change specifications and product design
without notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased equipment.
WARNING
GENERAL WARNING. Indicates information important to the proper operation of
the equipment. Failure to observe may
result in damage to the equipment and/or
severe bodily injury or death.
Throughout this manual, you will find the following safety words and symbols that signify important safety issues
with regards to operating or maintaining the Miracle Steamer.
WARNING
ELECTRICAL WARNING. Indicates information relating to possible shock hazard.
Failure to observe may result in damage
to the equipment and/or severe bodily
injury or death.
CAUTION
GENERAL CAUTION. Indicates information important to the proper operation of
the equipment. Failure to observe may
result in damage to the equipment.
WARNING
HOT SURFACE WARNING. Indicates
information important to the handling of
equipment and parts. Failure to observe
caution could result in personal injury.
IMPORTANT SAFETY INFORMATION
MIRACLE STEAMER
2
P/N 1010699 Rev. B
A.J. Antunes & Co.
Model Designation
TYPE OF POWER CORD
H = HARMONIZED
C = COMMERCIAL
TYPE OF PLUG
C = CEE 7/7 Schuko
F = NEMA 5-15P
V = NEMA 6-20P
MS-150XX
Service/Technical Assistance
If you experience any problems with the installation or
operation of your unit, contact your local Roundup
Authorized Service Agency. They can be found in the
service agency directory packaged with the equipment.
Fill in the information below and have it handy when
calling your authorized service agency for assistance.
The serial number is on the specification plate located
on the rear of the unit.
Purchased From:
Date of Purchase:
Model No.:
Serial No.:
Mfg. No.:
Refer to the service agency directory and fill in the
information below:
Authorized Service Agency
Name:
Phone No.:
Address:
50 =Timer/Spatula Model
55 = Timer/Drawer Model
1 = Self-Contained Water Tank
2 = Direct Water Hook-Up
3 = Front Water Drawer
Use only genuine Roundup replacement parts in this
unit. Use of replacement parts other than those supplied by the manufacturer will void the warranty. Your
Authorized Service Agency has been factory trained
and has a complete supply of parts for this unit.
You may also contact the factory at 1-877-392-7854 or
1-630-784-1000 if you have trouble locating your local
authorized service agency.
MIRACLE STEAMER
3
P/N 1010699 Rev. B
A.J. Antunes & Co.
In addition to the warnings and cautions in this manual,
use the following guidelines for safe operation of the
unit.
• Read all instructions before using equipment.
• For your safety, the equipment is furnished with a
properly grounded cord connector. Do not
attempt to defeat the grounded connector.
• Install or locate the equipment only for its intended use as described in this manual. Do not use
corrosive chemicals in this equipment.
• Do not operate this equipment if it has a damaged cord or plug, if it is not working properly, or
if it has been damaged or dropped.
• This equipment should be serviced by qualified
personnel only. Contact the nearest Roundup
authorized service facility for adjustment or repair.
• Do not block or cover any openings on the unit.
• Do not immerse cord or plug in water.
• Keep cord away from heated surfaces.
• Do not allow cord to hang over edge of table or
counter.
The following warnings and cautions appear
throughout this manual and should be carefully
observed.
• Turn the unit off, disconnect the power source
and allow unit to cool down before performing
any service or maintenance on the unit.
• The equipment should be grounded according
to local electrical codes to prevent the possibility of electrical shock. It requires a grounded receptacle with separate electrical lines,
protected by fuses or circuit breaker of the
proper rating.
• All electrical connections must be in accordance with local electrical codes and any
other applicable codes.
• WARNING ELECTRICAL SHOCK HAZARD.
FAILURE TO FOLLOW THESE INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR
DEATH.
- Electrical ground is required on this appliance.
- Do not modify the power supply cord plug.
If it does not fit the outlet, have a proper
outlet installed by a qualified electrician.
- Do not use an extension cord with this
appliance.
- Check with a qualified electrician if you are
in doubt as to whether the appliance is
properly grounded.
• This equipment is to be installed to comply
with the basic plumbing code of the Building
Officials and Code Administrators, Inc.
(BOCA) and the Food Service Sanitation
Manual of the Food and Drug Administration
(FDA).
• If the supply cord is damaged, it must be
replaced by the manufacturer or its service
agent, or a similarly qualified person.
• Do not clean this appliance with a water jet.
• Do not use a sanitizing solution or abrasive
materials. The use of these may cause damage to the stainless steel finish.
• To ensure proper steaming characteristics,
some mineral deposits must be present on
generator casting. If, during cleaning, the
casting does become free of mineral deposits,
one approved method is to add plain tap
water to casting and allow it boil off. This will
ensure proper steaming characteristics by
creating a thin layer of mineral deposits on
the casting.
• Chlorides or phosphates in cleansing agents
(e.g. bleach, sanitizers, degreasers or detergents) could cause permanent damage to
stainless steel equipment. The damage is
usually in the form of discoloration, dulling of
metal surface finish, pits, voids, holes or
cracks. This damage is permanent and not
covered by warranty.
MIRACLE STEAMER
4
P/N 1010699 Rev. B
A.J. Antunes & Co.
Voltage Watts Amps Hertz
120 1800 15.0 50/60
208 3300 15.9 50/60
220 3018 13.8 50/60
230 3300 14.4 50/60
240 3592 15.0 50/60
SPECIFICATIONS
Electrical Ratings
Electrical Cord & Plug Configurations
CAUTION
All electrical connections must be in accordance
with local electrical codes and any other applicable codes.
WARNING
ELECTRICAL SHOCK HAZARD.
FAILURE TO FOLLOW THE INSTRUCTIONS IN
THIS MANUAL COULD RESULT IN SERIOUS
INJURY OR DEATH.
• Electrical ground is required on this appliance.
• Do not modify the power supply cord plug. If it
does not fit the outlet, have a proper outlet
installed by a qualified electrician.
• Do not use an extension cord with this appliance.
• Check with a qualified electrician if you are in
doubt as to whether the appliance is properly
grounded.
Letter Description Configuration
Code*
C CEE 7/7 Schuko
F NEMA 5-15P
V NEMA 6-20P
C Commercial Cord
H Harmonized Cord
* Used in Model Designation
• The following tips are recommended for maintenance of your stainless steel equipment,
- Always use soft, damp cloth for cleaning,
rinse with clear water and wipe dry. When
required, always rub in direction of metal
polish lines.
- Routine cleaning should be done daily
using soap, ammonia detergent and water.
- Stains and spots should be sponged using
a vinegar solution as required.
- Finger marks and smears should be
rubbed off using soap and water.
- Hard water spots should be sponged using
a vinegar solution.
MIRACLE STEAMER
5
P/N 1010699 Rev. B
A.J. Antunes & Co.
Dimensions
20-3/4"
(52.7 cm)
21-3/16" (53.8 cm)
17-11/32" (28.8 cm)
14" (35.5 cm)
8-13/32"
(21.4 cm)
MS-150/155 & MS-250/255
25" (63.5 cm)
17-5/32" (43.5 cm)
14" (35.5 cm)
MS-355
25"
25"
17-5/32"
14"
MIRACLE STEAMER
6
P/N 1010699 Rev. B
A.J. Antunes & Co.
Unpacking
1. Remove unit and all packing materials from shipping carton.
2. Open the large box. It should contain the following:
• Miracle Steamer,
• Handle, Handle Guard & Shoulder Bolt,
(MS-150/250 only)
• Water Hookup Kit (MS-250 only).
NOTE: If any parts are missing or damaged, contact
Antunes Technical Service IMMEDIATELY at 1-877-
392-7854 or 1-630-784-1000.
3. Remove all packing materials and protective coverings from the unit.
4. Remove and wash all removable parts in soap
and water. Rinse with clean hot water and allow
to air dry.
5. Wipe all surfaces of the unit with a hot damp
cloth.
NOTE: Do not use a dripping wet cloth. Wring out
before use.
6. MS-150/250 Models: Assemble the handle, han-
dle guard and mounting bolt to the spatula as
shown in Figure 1.
7. Re-install all removed parts.
Equipment Setup
GENERAL
When placing the unit into service, pay attention to the
following guidelines:
• Make sure power to the unit is off and the unit is
at room temperature.
• Do not block or cover any openings on the unit.
• Do not immerse cord or plug in water.
• Keep cord away from heated surfaces.
• Do not allow cord to hang over edge of table or
counter.
ELECTRICAL
1. Place the unit on a sturdy, level table or other
INSTALLATION
Figure 1. Assembling Handle–MS-150/250 Only
Bolt
work surface. Turn the rocker switch (power
ON/OFF to OFF before proceeding.
2. Ensure that the line voltage corresponds to the
stated voltage on the units specification label and
power cord warning tag.
3. Connect the unit to the power supply.
Handle
Spatula
Guard
THIS APPLIANCE MUST BE
THIS APPLIANCE MUST BE
THIS APPLIANCE MUST BE
EARTHED GROUNDED
EARTHED GROUNDED
EARTHED GROUNDED
120 VAC
ONLY
THIS APPLIANCE MUST BE
EARTHED GROUNDED
THIS UNIT IS DESIGNED TO OPERATE
ON 120 VOLTS ONLY. APPLICATION
WITH ANY OTHER VOLTAGE SUPPLY
COMPLETELY VOIDS ALL WARRANTY.
PLEASE CHECK YOUR LINE VOLTAGE
BEFORE INSERTING THIS PLUG INTO
THE RECEPTACLE.
THIS APPLIANCE MUST BE
THIS APPLIANCE MUST BE
THIS APPLIANCE MUST BE
EARTHED GROUNDED
EARTHED GROUNDED
EARTHED GROUNDED
208 VAC
ONLY
THIS APPLIANCE MUST BE
THIS APPLIANCE MUST BE
THIS APPLIANCE MUST BE
EARTHED GROUNDED
EARTHED GROUNDED
EARTHED GROUNDED
220-240 VAC
ONLY
THIS APPLIANCE MUST BE
EARTHED GROUNDED
THIS UNIT IS DESIGNED TO OPERATE
ON 208 VOLTS ONLY. APPLICATION
WITH ANY OTHER VOLTAGE SUPPLY
COMPLETELY VOIDS ALL WARRANTY.
PLEASE CHECK YOUR LINE VOLTAGE
BEFORE INSERTING THIS PLUG INTO
THE RECEPTACLE.
THIS APPLIANCE MUST BE
EARTHED GROUNDED
THIS UNIT IS DESIGNED TO OPERATE
ON 220-240 VOLTS ONLY. APPLICATION
WITH ANY OTHER VOLTAGE SUPPLY
COMPLETELY VOIDS ALL WARRANTY.
PLEASE CHECK YOUR LINE VOLTAGE
BEFORE INSERTING THIS PLUG INTO
THE RECEPTACLE.
MIRACLE STEAMER
7
P/N 1010699 Rev. B
A.J. Antunes & Co.
CAUTION
All electrical connections must be in accordance
with local electrical codes and any other applicable codes.
WARNING
ELECTRICAL SHOCK HAZARD.
FAILURE TO FOLLOW THE INSTRUCTIONS IN
THIS MANUAL COULD RESULT IN SERIOUS
INJURY OR DEATH.
• Electrical ground is required on this appliance.
• Do not modify the power supply cord plug. If it
does not fit the outlet, have a proper outlet
installed by a qualified electrician.
• Do not use an extension cord with this appliance.
• The unit should be grounded according to
local electrical codes to prevent the possibility
of electrical shock. It requires a grounded
receptacle with separate electrical lines, protected by fuses or circuit breaker of the proper
rating.
• Check with a qualified electrician if you are in
doubt as to whether the appliance is properly
grounded.
PLUMBING
NOTE: Miracle Steamer models are designed to use
cold tap water. Distilled water may be used to reduce
mineral deposit build-up and reduce maintenance
costs.
CAUTION
This equipment is to be installed to comply with
the basic plumbing code of the Building Officials
and Code Administrators, Inc. (BOCA) and the
Food Service Sanitation Manual of the Food and
Drug Administration (FDA).
Figure 2. Filling Water Tank–MS-150/155
Filter
Sliding Cover
Figure 3. Filling Water Tank–MS-355
Indicator Light (Low water)
Model MS-150/155 & MS-355
The MS-150/155 & MS-355 models have a self-contained water supply and is portable. To fill the self-contained water tank:
1. MS-150/155: Open the sliding tank cover on top
of the unit (Figure 2).
NOTE: Make sure filter inside tank is installed
properly.
MS-355: Open the sliding tank drawer on the side
of the unit (Figure 3).
2. Pour in cold tap water. The tank will hold approximately 3 quarts (2.81 liters).
3. Close the water tank.
CAUTION
Use cold water only.
R
E
A
D
Y
ADD
WATER
READY
MIRACLE STEAMER
8
P/N 1010699 Rev. B
A.J. Antunes & Co.
OPERATION
General
When the operate button (Figure 5) is pressed, power
is supplied to the water pump (MS-150/155/355) or
solenoid (MS-250/255). The pump/solenoid operates
and water sprays onto the heated steam generator.
The water flashes immediately into live steam and
shoots down onto the product.
One of two operational modes can be used: Single
Shot or Timed Cycle
SINGLE SHOT
The operate button is pressed to initiate a single timed
shot. The control board applies power to the water
pump/solenoid and a timed “shot” of steam occurs.
TIMED CYCLE
The control is set to the desired cook time (up to 99
minutes, 59 seconds), then the Start/Stop Button is
pressed. The main control board applies power to the
water pump/solenoid at regular intervals for the duration of the displayed cycle time. The display counts
down to zero when the cycle is complete sounding a
audible signal then reverts back to the original programmed cycle time. The unit is ready for the next
cycle when the green ready light is on.
Figure 5. Operating Controls
Ready Light
Rocker Switch
(Power On/Off)
Operate
Button
Message
Display
Start/Stop
Button
CAUTION
Water pressure must not exceed 25 psi (1.7
kg/cm2or 172 kPa). Higher water pressures may
cause poor performance or flooding. To reduce
water pressure, install a water pressure regulator,
and set water pressure to 20 psi (1.4 kg/cm
2
or 138
kPa). To order a water pressure regulator from
your authorized service center, order Roundup
part no. 7000235.
Figure 4. Connecting Water Supply to MS-250/255
Hi-Limit Reset Button
Water Connect Fitting
Power Cord
Quick Disconnect
Insert
Model MS-250/255
The MS-250/255 requires a direct water hookup. An
installation kit is packed inside the unit.
1. Connect the 1/4" (6.5 mm) I.D. flexible tubing to
your cold water line using the supplied hose
clamp.
2. Push the quick disconnect insert into the fitting on
the back of the unit (Figure 4).
NOTE: Incoming water is controlled by a solenoid
valve inside the electrical housing of the steamer.
RE
AD
Y
READY
UP DOWN PROGRAM START/STOP
POWER
Loading...