Antunes BEV-D Installation Manual
A. J. ANTUNES & CO. 180 Kehoe Blvd., Carol Stream, Illinois 60188
CO2 Water Inlet
(From Carbonator)
CO2 Water Outlet
(Insulated Line to
Cold Plate)
Cold Plate
Drain Water Inlet
Drain Water Outlet
to Floor Drain
Drain Water Outlet
< 12 o'clock position >
(To Floor Drain)
CO
2
W ater Inlet
(from Carbonator)
Drain
Water Inlet
(From Cold Plate)
CO
2
W ater Outlet
(To Cold Plate)
Alternate Drain Water Outlet
< 6 o'clock position >
(Insert Plug)
Thermal
Insulation
5.5 inches
(13.8 cm)
17 inches
(42.5 cm)
PLUG
CHILL BEV-D INSTALLATION INSTRUCTIONS (P/N 9700925)
SUGGESTED MATERIALS AND EQUIPMENT NEEDED:
• (10 ft.) 3/4” PVC Pipe
• (4) 3/4” PVC Elbow Fitting
• Multipurpose glue for ABS, PVC, and CPVC
• Tubing Cutter
• PVC Pipe Cutter
• Screwdriver or Drill with Bits
• Channel-Lock Pliers
• Adjustable Wrench
• Measuring Tape
NOTE: Do NOT use copper tubing for the CO2 water line.
General
If you experience any problems with these instructions,
contact the Technical Service Department at 630-784-1000
or toll free in the U.S. at 877-392-7854.
Warranty Information
All BEV-D units will be free from defects in materials and
workmanship for a period of five years.
General Specifications
CO2 Water Connections
Sump Water Connections 3/4” (1.91 cm) PVC fittings
Operating Pressure Max. 150 psi (10.3 kg/cm²)
Electrical Connections None
Installing the BEV-D
To ensure material compatibility, a multipurpose glue for ABS,
PVC, and CPVC must be used. This will ensure a proper bond
between the 3/4” PVC and the black ABS Drain Water Inlet.
The BEV-D is furnished with an assortment of plumbing fittings
and insulating tape to aid in installation. However, due to the
variety of equipment and numerous methods of making connections, all fittings may not be used.
NOTE: Do NOT attach the soda drip tray line to the BEV-D.
The excess soda in the drip tray should drain separately to
the floor drain. The BEV-D should only be attached to the
cold-plate drain line that contains the melted ice water.
1. Place the BEV-D on its side (horizontally) beneath the ice
bin and attach with the included mounting straps.
NOTE: Due to gravity flow restrictions, the BEV-D must be
mounted entirely beneath the ice bin.
3/8” (0.95 cm) barbed fittings
with 360° swivel
Figure 1. Typical Installation
Figure 2. Specifications Diagram
2. Position the BEV-D so the two 3/4” PVC Drain Water Outlets
are oriented in the 12 o’clock and 6 o’clock positions.
3. Glue the PVC plug in the 6 o’clock PVC Drain Water Outlet.
4. Install a PVC drain line from the 12 o’clock Drain Water
Outlet to the floor drain.
1-877-392-7836 Fax: 630-784-1000 Page 1 of 2 P/N 1011075 Rev. A 05/10
A. J. ANTUNES & CO. 180 Kehoe Blvd., Carol Stream, Illinois 60188
CHILL BEV-D INSTALLATION INSTRUCTIONS (P/N 9700925)
5. Attach the cold-plate melt line to the 3/4” Drain Water
Inlet. This line can be vinyl tubing or PVC pipe.
NOTE: If using vinyl tubing, make sure there are no pinches
or kinks in the tubing.
NOTE: This line should be insulated to keep the water as
cold as possible before it enters the unit and prevent condensation.
NOTE: Because the cold plate drain line is gravity fed, you
should minimize any obstructions to the flow in the tubing.
6. Turn off the fresh water supply valve.
7. Turn off or unplug the carbonator.
8. Relieve the line pressure by depressing the soda valve.
9. Locate the filtered CO2 water line from the carbonator
and connect the line to the BEV-D CO2 Water Inlet as
indicated on the unit.
10. Connect the pre-chilled BEV-D CO2 Water Outlet to the
cold plate with an insulated line.
11. Turn on the fresh water supply and the carbonator.
12. Check for water leaks.
1-877-392-7836 Fax: 630-784-1000 Page 2 of 2 P/N 1011075 Rev. A 05/10
Loading...