ASSEMBLY INSTRUCTIONS
Zido® Cart
Product Part#
Zido Carts ZD2231SB/CG4
ZD2235SB/CG4
ZD2240SB/CG4
ZD2531SB/CG4
ZD2535SB/CG4
ZD2540SB/CG4
ZD2166SB/CG4
Zido Pole Cart ZD2166SB4
Toll-free: 800.325.3841 | Fax: 800.325.0045 | email: sales@anthro.com | anthro.com
Anthro Corporation® | 10450 SW Manhasset Dr. | Tualatin, OR 97062
Outside the U.S. | Tel: 503.691.2556 | Fax: 503.691.2409
Rev H, January 2011
08
03
06
09
02
WELCOME
Thank you for purchasing Zido. If you
have any questions or if we can help
you in any way, please contact us at
800.325.3841.
PARTS LIST
Before beginning assembly of your Zido
cart please review the parts list to verify
that your shipment is complete.
All Screw quantities listed here are the
minimum needed for your Zido assembly.
There may be a few extra Screws included
which are not counted in the Parts List.
To make the assembly of your Zido even
easier, we have included the required
tools. The handy Hex Driver Bit can be
used in your electric drill in place of the
Hex Driver.
Product Quantity Part Number
Hex Driver 5/32” 1 375-5000-00
(not shown)
Hex Driver Bit 5/32” 1 375-5003-00
(not shown)
2
07
05
01
04
Zido Cart Quantity Part Number
01 Base
Small, 22" wide 1 250-3064-00
Large, 25" wide 1 250-3065-00
02 Tube
24" long (for 31” high cart) 1 500-1031-00
28" long (for 35” high cart) 1 500-1030-00
33" long (for 40” high cart) 1 500-1032-00
03 Cap Shelf
22” wide 1 101-1025-06-50
25” wide 1 101-1026-06-50
04 Casters
4” Locking 2 150-5011-03
4” Non-locking 2 150-5010-03
05 Tapped Strip 1 225-2621-00
06 Cap Shelf Bracket 1 225-2620-00
07 3/4" Flat Head Screw 2 325-5466-00
08 Wood Screws 8 325-5106-00
09 1/2" Socket Head Cap Screw 4 325-5455-00
Zido Pole Cart Quantity Part Number
01 Base 1 250-3065-00
02 Tube 1 125-4324-00
04 Casters
4” Locking 2 150-5011-03
4” Non-locking 2 150-5010-03
05 Tapped Strip 1 225-2621-00
3/4" Socket Head Cap Screw (not shown) 2 325-5461-00
End Cap (not shown) 1 175-5235-00
ASSEMBLY SEQUENCE
Plan out the assembly to make your installation easier. We suggest this sequence to reduce interference
between accessories.
1. Pre-drill the top for accessories (Mouse Holder, Side Bin, Gel Cup/Probe Holder, Extension Tube).
2. Assemble the cart.
3. Base Storage Shelf.
4. Drawer, Keyboard Drawer, Handle.
5. Additional Shelves, Equipment Shelves, Metal Bin, IV bracket.
6. Cable Bin, Glove Box Holder, Tank Holder.
7. Mouse Holder, Side Bin, Gel Cup & Probe Holder, Extension Tube.
8. Pole Cart Handle, Flat Panel Mounts.
STEP 1
Connect the Base with the Tube
¡ Slide the nut bar into the bottom of the base
assembly, smooth side against the inside of the tube,
with the two threaded holes on the top and the single
threaded hole at the bottom. Loosely attach the nut
bar to the tube with one 3/4" Flat Head Screw.
¡ Slide the tube into the base so that the notch at the
bottom of the tube goes over the screw. Align the
upper hole on the base with a threaded hole on the
nut bar. (For the 25w cart and the Pole Cart, you'll use
the top hole; for the 22w cart, you'll use the second
hole.) Loosely attach the nut bar, tube, and base with
the second 3/4" Flat Head Screw.
3/4" Flat Hd Screw
325-5466-00
STEP 2
Install the Casters
¡ Add the locking casters (the ones with the brakes) to
the front of the base assembly.
¡ Add the non-locking casters to the back of the
base assembly. If you have a Fixed-height Cart, skip
ahead to Step 3.
¡ If you have a Zido Pole Cart, make sure that the
holes on the column line up with the holes on the
base and tighten the screws. Next, insert the End
Cap in the top of the Pole. Congratulations! Your
assembly is complete!
3
Questions? Call us at 800.325.3841 or visit anthro.com. We’re happy to walk you through the assembly!
STEP 3
Assemble the Top
¡ Place the cap shelf upside down on a non-marring
surface. Locate the bracket. The bottom of the
bracket is flat and has no sticker. The top of the
bracket has a sticker that says "TOP" and has bumps
with threads inside. The bumps on the top of the
bracket nest inside the holes on the cap shelf. Place
the bracket upside down on the shelf so that the holes
on the bracket line up with the holes on the bottom of
the shelf. Using the eight non-threaded holes around
the outside of the bracket, attach the shelf to the
bracket with eight wood screws. Use the 5/32" hex
driver.
¡ If you have purchased a Zido Handle for this
configuration, install it now. If any of your accessories
require that you drill the shelf, do that now.
STEP 4
Install the Top Assembly
¡ Set the top assembly onto the top of the base assembly
so that the cap shelf extends over the front of the base.
3/4" Wood Screw
325-5106-00
¡ Secure with four 1/2" socket head screws.
Be sure to drive the screws by hand using the
ball driver provided.
¡ Double-check the alignment of the cap shelf with the
column and the base. Rotate the column if needed, then
tighten the 3/4" screws that connect the column to the
base.
1/2" Socket Hd Screw
325-5455-00
CONGRATULATIONS! YOUR ZIDO CART ASSEMBLY IS COMPLETE!
Anthro Corporation® | 10450 SW Manhasset Dr. | Tualatin, OR 97062
Toll-free: 800.325.3841 | Fax: 800.325.0045 | email: sales@anthro.com | anthro.com
Outside the U.S. | Tel: 503.691.2556 | Fax: 503.691.2409
*300-5404-00*
300-5404-00
Zido carts have a Lifetime Warranty; the cylinder has a five-year warranty.
Technology Furniture and Zido are trademarks of Anthro Corporation. Anthro reserves the right to modify the design and specifications without prior notice.
Warranty:
Notices:
4
Questions? Call us at 800.325.3841 or visit anthro.com. We’re happy to walk you through the assembly!
Loading...