Anthro Unit 30, Unit 36, Unit 48 Assembly Instructions
R
30”/36”/48” wide Adjusta Unit
Assembly Instructions
Hello! Thank you for choosing Anthro.
Before beginning assembly of your Adjusta Unit, take a moment to review the parts listed on the next page
to verify that your shipment is complete. Please review the assembly instructions of all Anthro products you
purchased and are planning to include in this installation, prior to beginning this assembly.
To make the assembly of your Adjusta Unit even easier, we have included all of the required tools. The handy
Hex Driver Bit can be used in your electric drill in place of the Hex Driver. Your Adjusta Unit is heavy! A second
person will make this assembly procedure much easier.
Hex Driver 5/32” ............................................................ 375-5000-00
Hex Driver Bit 5/32” ..................................................... 375-5003-00
Hex Key 5/32” ................................................................. 375-5016-00
Hex Key 3/16” ................................................................. 375-5028-00
3-Way Wrench .............................................................225-5196-03
8 oz. Rubber Mallet ..................................................... 375-5022-00
Thank you for buying our Products!
Please return the enclosed Registration Card to receive our product
updates, new catalogs, and sale flyers.
Anthro Corporation Technology Furniture®
10450 SW Manhasset Drive
Tualatin, Oregon 97062
anthro.com
Questions? 1-800-325-3841
Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com
1-800-325-3841
SAVE THESE INSTRUCTIONS!
Rev. C January 2006
Component list for part #’s FAJ30zz/xx3, FAJ36zz/xx3 & FAJ48zz/xx3
02
06
03
04
05
01
07
15
16
17
18
19
20
19
Step 12
Align the Base Assembly on the Vertical Tubes as shown.
Secure the Base Assembly by inserting a fit Bolt through a
Tube Washer. Then insert the Bolt through the Base Tube
and carefully thread it into the Vertical Tubes.
Repeat for the remaining three Bolts and tighten all Bolts.
fit Tube
Washer
fit Bolt
Locking Casters
09
NOTE: Detailed views of all Hardware are provided with each Assembly Step.
01–fit Adjusta Fixed Worksurface Qty. 1 ....................... (see below)
30” Wide Fixed Worksurface (FAJ30zz/xx3) ....100-6454-00
36” Wide Fixed Worksurface (FAJ36zz/xx3) ....100-6455-00
48” Wide Fixed Worksurface (FAJ48zz/xx3) ....100-6456-00
02–fit Adjusta Caddy Worksurface Qty. 1 ....................... (see below)
30” Wide Caddy Worksurface (FAJ30zz/xx3)..100-6458-00
36” Wide Caddy Worksurface (FAJ36zz/xx3) ..100-6459-00
48” Wide Caddy Worksurface (FAJ48zz/xx3) ..100-6460-00
03– fit Adjusta Mechanism...............Qty. 1 ....................... (see below)
(The Adjusta Mechanism is packaged separately & requires assembly)
30” Wide Adjusta Mechanism (FAJ30zz/xx3) ...225-5545-00
36” Wide Adjusta Mechanism (FAJ36zz/xx3) ...225-5546-00
48” Wide Adjusta Mechanism (FAJ48zz/xx3) ...225-5547-00
04– Small Support Bracket X .............Qty. 1 ...................225-2014-00
05– 24.875” Vertical Legs .................Qty. 4 ...................125-5230-00
06– Adjusta Base Tubes ......................Qty. 2 ..................125-5276-00
08– Insert Screws ................................. Qty. 4 ...................325-5052-00
09– 2.0” Large End Caps ...................Qty. 4 ...................175-5157-00
10– Caster Inserts ............................... Qty. 4 ...................525-5032-00
11– 3” Locking Casters ......................Qty. 2 ...................150-5053-00
12– 5/16-18 fit Bolts ..............................Qty. 8 ...................325-5194-00
13– fit Tube Washers .........................Qty. 8 ..225-2050-00 or 225-3522-00
14– 3” Non-Locking Casters ........... Qty. 2 ...................150-5052-00
15– 3/4” Wood Screws ........................Qty. 42 ................325-5106-00
16– Back Trough .................................... Qty. 1 ....................... (see below)
30” Wide Back Trough (F3029zz/xx3) ................225-2290-00
36” Wide Back Trough (F3629zz/xx3) ................225-2291-00
48” Wide Back Trough (F4829zz/xx3) ................225-2292-00
17– Support Screws ............................ Qty. 8 ...................325-5010-00
18– Small Support Bracket Y ............Qty. 1 ...................225-2015-00
19– 1/4-20 Button Head Screws ...... Qty. 4 ...................325-5003-00
20– 1.5” Small Caps .............................Qty. 4 ...................175-5156-00
07– Cross Tubes .................................... Qty. 2 ....................... (see below)
30” Wide Cross Tube (FAJ30zz/xx3) ...................125-5219-00
36” Wide Cross Tube (FAJ36zz/xx3) ...................125-5220-00
48” Wide Cross Tube (FAJ48zz/xx3) ...................125-5214-00
All Fastener quantities listed here are the minimum needed
for your Adjusta Unit assembly. There may be a few extra
Fasteners included, which are not counted in the Parts List.
10
08
11
12
13
14
(5/16-18 X 3.5”) fit Bolt
325-5194-00
fit Tube Washer
225-2050-00 or 225-3522-00
Step 13
Insert the four 1.5” Small End Caps into the Vertical Legs.
Congratulations! Your assembly is complete.
Please return the enclosed Registration Card to receive
our product updates, new catalogs, and sale flyers.
Thank you for choosing Anthro!
Adjust the Caddy Worksurface height by:
1. Squeezing and holding the Paddle.
2. Reposition the Caddy to the desired location.
3. Release the Paddle.
Adjust the Caddy Worksurface angle by:
1. Rotating the Knobs counterclockwise.
2. Reposition the Caddy to the desired angle.
3. Rotate the Knobs clockwise.
1.5” Small
End Cap
Rotate Knobs
to adjust
Caddy angle.
Squeeze Paddle
to adjust Caddy height.
Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 1-800-325-3841
anthro.com
Loading...