Anthro UltraCompact Cart Assembly Instructions
Step 8
Install all four Caster Inserts into the Base Tube and
secure with one Insert Screw per Insert. Push the
Casters, (locking ones in front) into the Caster Inserts.
Next, place the Base Tube Assembly onto the Vertical Legs
of the Shelf Assembly. Attach the Base Tube to each Leg
using a total of four Base Tube Screws.
Insert Screw
(small pink patch on end)
325-5052-00
Base Tube Screw
325-5000-00
Thread each Glide
into the Glide Inserts
Step 9
Unpack the remaining Keyboard & Mouse Caddy items.
First, slide the Caddy Mechanism into the installed Tray
and push to the rear.
NOTE: If needed, rotate the Mechanism Handle and LIFT to
allow the Mechanism to slide to the rear.
Second, install the remaining Wood Screw and Rubber
Bumper into the front of the Tray.
3
/4” W ood Screw
325-5106-00
Step 10 (requir es the Crescent Wrench & Screwdriver)
Caddy Screws
Carefully rotate your Cart back onto the Casters.
Pull the Mechanism to the front and place the Platform
onto the Mechanism. Secure the Platform using the four
Platform
Caddy Screws and Acorn Nuts.
Then, place the Mouse Rail, Pad & Wrist Rest onto the
Platform as best suits your personal preference.
Pop the Small End Caps into the Legs and the Large End
Caps into the Base Tube. Congratulations! Your assembly
is complete.
(#10-24) Cadd y Screw
575-5001-10
(#10-24) Acorn Nut
325-5023-00
Adjusting your Keyboard & Mouse Caddy
Adjust the Platform height & angle:
1. Rotate the Handle counterclockwise.
2. Reposition the Shelf, then retighten the Handle.
Adjust the Platform rotation:
1. Firmly grasp the Platform, then rotate to the desired angle.
Locking
Casters
GLIDES ONLY
Rotate Handle
Rubber Bumper
Acorn
Nuts
to LIFT
Wood Screw
Caddy Mechanism
Rotate
2
NOTE: The Rubber Bumper is located
towards the rear of the Cart
Rubber Bumper
Rear
of
Cart
KB Pads
Wrist Rest
Mouse
Pad
Mouse Rail
1
UltraCompact Cart
Assembly Instructions
Hello! Thank you for choosing Anthro.
Before beginning assembly of your
UltraCompact Cart, please take a
moment to review the parts listed below
to verify that your shipment is complete.
It may be helpful to review the
assembly instructions of all Anthro
products you purchased and are
planning to include in this installation.
A Philips Head Screwdriver & Adjustable Crescent Wrench (not included)
will be required for this assembly.
4Does your Cart have 4” Casters?*
(Such as a 075xx4. Your Caster Part Numbers are given here.)
4” Non-Locking Caster
4” Locking Caster
150-5011-00
4Does your Cart have Glides?*
(Such as a 075xxGL. Your Glide and Glide
Insert Part Numbers are given here.)
Glide Insert
525-1004-00
Component list for part #
075xx , 075Lxx
01– Caddy T ray................................. Qty. 1 .................225-5046-00
02– Rubber Bumpers ..................... Qty. 2 .................175-5130-03
03– Caddy Screws........................... Qty. 4 ................. 575-5001-10
04– Ke yboard Pads.......................... Qty. 4 .................575-5001-11
05– Wrist Rest ................................ Qty. 1................. 575-5001-01
06– Caddy Platform........................ Qty. 1 .................575-5001-04
07– Acorn Nuts............................... Qty. 4 .................325-5023-00
08– Caddy Mechanism ................... Qty. 1 ................. 575-5001-09
09– Mouse Pad................................. Qty. 1 ................. 575-5001-03
10– Mouse Rail................................. Qty. 1................. 575-5001-02
11–3/4” W ood Screws .................... Qty. 10...............325-5106-00
12– 1.75” Large End Caps............. Qty. 2 ..................175-5021-xx
13– 2 3/8” Locking Casters ............ Qty. 2 .............. 150-5003-00*
14– Base T ube Screws .................... Qty. 4 ................. 325-5000-00
15– Caster Inserts ........................... Qty. 4...............525-1000-00*
16– Insert Screws ............................ Qty. 4.................325-5052-00
150-5010-00
Glide
325-5042-00
23
22
®
21
TECHNOLOGY FURNITURE
24
25
26
16
17
15
14
13
05
04
03
02
01
11
09
12
10
06
ITEMS 01-11
ARE BOXED SEPARATELY
07
08
FROM YOUR CART
17–2 3/8” Non-Locking Casters... Qty. 2.............. 150-5002-00*
18– V ertical Legs.............................. Qty. 4..................125-5049-xx
19– 1.5” Small End Caps ............... Qty. 4..................175-5020-xx
20– Clamp Screws........................... Qty. 8.................325-5086-03
21– Shelf Supports .......................... Qty. 8..................175-5060-xx
22– Shelf Clamps ............................. Qty. 8..................175-5059-xx
23– Support Screws........................ Qty. 8.................325-5010-00
24– Ultra Compact Large Shelf.... Qty. 1..................100-6001-xx
25– Ultra Compact Small Shelf .... Qty. 1..................100-6005-xx
26– Ultra Compact Base Tube...... Qty. 1..................125-5046-xx
All Screw quantities listed here are the minimum needed
for your Cart assembly. There may be a few e xtra Screws
included, which are not counted in the Parts List.
The following Tools (not shown) have been included with your Cart.
Hex Driver 5/32"......................... Qty. 1 ................. 375-5000-00
Hex Driver Bit 5/32"................... Qty. 1 ................. 375-5003-00
19
20
18
Questions? 1-800-325-3841
1-800-325-3841
Anthro® Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com
SAVE THESE INSTRUCTIONS!
Rev. B June 2003
Ultra Compact Cart
Assembly Instructions
Step 1
Before proceeding, please review the Assembly
Instructions of all Anthro Products you purchased
and are planning to include in this installation.
Questions? 1-800-325-3841
Step 4
Unpack the Universal Keyboard & Mouse Caddy items.
Align the ten Caddy Tray holes with those on the underside of
your Cart’s Large Shelf. Secure the Tray using eight Wood
Screws (installed on the edges of the Tr ay).
Finally, insert one Wood Screw through a Rubber Stop and
install the Stop towards the “rear” of your Cart.
NOTE: One hole will be left open.
NOTE: There is more
distance from the
Shelf Supports to the
Front Shelf edge
Rubber Bumper
These Instructions will cover both the Ultra Compact
Cart and Universal Ke yboard & Mouse Caddy assembly.
You may disregard the Keyboard & Mouse Caddy Instructions
that came in the separate packaging.
Step 2
Determine the best location for your Cart’s Shelves.
Your Cart is designed to have the Large Shelf installed
above the Small Shelf (as shown in these instructions).
For a Small Shelf location that is higher or lower than
16” from the floor, refer to the illustrations shown at
right to determine which hole to attach your Small Shelf.
Once assembled, it is very difficult to move a Shelf
without taking the Cart apar t and star ting over.
NOTE: These instructions will place your Small Shelf 16” from
the floor using the standard 2
REMINDER: You may want to
measure your equipment to
make sure it fits between the
selected Shelf locations.
3
/8” Casters.
DON’T FORGET: The Keyboard
Caddy will require additional space
between the Shelves in order to fully
slide to the back of the Tray.
Step 3
Attach four Shelf Supports to both Shelves.
Begin by first installing a Shelf Clamp into the Shelf
notch. Be sure the pointed “barbs” face towards the
outer Shelf edge.
Slide a Shelf Support into the recesses of the Shelf
Clamp and Shelf. Push in as far as possible.
Secure with a Clamp Screw.
Ultra Compact Cart shown with
075xx
the Universal Keyboard & Mouse
Caddy and 2 3/8” Casters
(075Lxx available with Mouse
Caddy on left)
Hole 9=17”
Hole 8=16” (measured from the coped end)
Hole 7=15”
16”
Coped end
075xx, 075Lxx with 2 3/8” Casters shown
16”
075xx4, 075Lxx4 with 4” Casters shown
075xxGL, 075LxxGL with Glides shown
Barbs
First
Next
Hole 8=17”
Hole 7=16”
Hole 6=15”
16”
Hole 11= 1 7”
Hole 10= 1 6”
Hole 9=15”
1
/2” W ood Screw
325-5106-00
Step 5
Loosely attach the Small Shelf to Hole 8 from the
bottom (coped end) of two Vertical Legs using two
Support Screws.
NO TE: Handle the Shelf Assembly carefully until the Cart is
fully assembled.
Support Screw
325-5010-00
(using 2 3/8” Casters)
Step 6
Loosely attach the Large Shelf to Hole 2 from the
top (non-coped end) of the Vertical Leg Assembly
(from Step 5) using two Support Screws.
TIP: Use the holes in the Ver tical Legs as a ruler to
ensure that your Support Screws are installed into the
correct locations.
Top (non-coped) end
Support Screw
325-5010-00
Step 7
Loosely attach the 3rd and 4th Vertical Legs to the Shelf Assembly (from Step 6) using one Support Screw per Shelf Support.
Once all four Vertical Legs are attached, tighten all Support Screws.
TIP: Use the holes in the Vertical Legs as a ruler to ensure that your
Support Screws are installed into the correct locations.
In preparation for Step 8, rotate your Cart upside down.
Do not install a Wood
Screw into this hole
Insert one Suppor t Screw
through each Shelf Support
Hole 8=16”
Bottom (coped) end
Rubber Bumper
Bottom (coped) end
Hole 2
Rubber Bumper
Clamp Screw
325-5086-03
Anthro® Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com
Last
Support Screw
325-5010-00
anthro.com
Loading...