Anthro Trolley Assembly Instructions
Step 7a
Threaded holes
Install Non-skid Pads on the top of the Trolley Trunk
Covers to cushion the edge of each Trunk Assembly
where it meets the cover. Install pads on the inside face
of the cover, at the edge, about 3.5” below the threaded
holes at the top of the cover.
Non-Skid Pad
175-5068-03
Step 7b
STOP: IF YOU PURCHASED A TROLLEY
EQUIPMENT SHELF, ADDITIONAL WOOD SHELF,
OR TROLLEY TRAY READ THOSE INSTRUCTIONS
BEFORE INSTALLING THE TRUNK COVERS.
Install the Trolley Trunk Covers by orienting both Covers
with the Trunk Assemblies.
Secure the top and bottom of each Cover using a total of
four Button Head Screws per Cover.
Button Head Screws
Trunk Cover
Button Head
Screws
3.5”
Non-Skid Pads
Trolley Cart
Assembly Instructions
Hello!
Thank you for choosing Anthro.
Before beginning assembly of your
Trolley, please take a moment to
review the parts listed below to verify
that your shipment is complete.
All fastener quantities shown are the
minimum needed for this assembly.
There may be a few extras provided
which are not required.
The following Tools (not shown at right)
have been provided:
Hex Driver 5/32” ...... 375-5000-00
Hex Key 6mm ......... 375-5013-00
3
/16” Allen Key ..........375-5028-00
3-way Wrench ......... 225-5196-03
5/32” Driver Bit ..... 375-5003-00
02
15
16
17
01
18
TECHNOLOGY FURNITURE
14
12
11
10
09
08
07
®
13
(1/4-20 X .375”) Button Head
Screw
325-5210-00
Step 8
STOP: IF YOU PURCHASED A SWING OUT MOUSE SHELF
READ THOSE INSTRUCTIONS BEFORE INSTALLING THE
TO P.
Finally, place the main Trolley Shelf onto the installed
Shelf & Handle Sides, aligning the six holes on the
Shelf with those on the Sides.
Secure the Shelf to the Sides using a total of six
3
/4” Wood Screws. Tighten all Screws and Nuts.
Congratulations! Your assembly is complete!
3
/4” Wood Screw
325-5106-00
Questions? 1-800-325-3841
3
/4” Wood Screws
into the six Trolley
Shelf holes
Component list for
03
part # TR18zz/xx and TT18zz/xx.
01– Trolley Trunk Assembly (X) ...Qty. 1 .............................................
TR18zz/xx ...................................................................... 835-5018-00
TT18zz/xx ...................................................................... 835-5401-00
02– 5” Total Lock Casters ............ Qty. 2 ................. 150-5081-00
03– 5/16-18 Button Head Screw.....Qty. 16 ................ 325-5188-00
04– 5/16-18 X 1” Tube Screws ....... Qty. 4 ................. 325-5136-00
05– 5” Swivel Lock Casters ......... Qty. 2 ................. 150-5080-00
06– Trolley Trunk Covers ................ Qty. 2 ............................................
TR18zz/xx ...................................................................... 225-5753-00
TT18zz/xx ...................................................................... 225-5278-00
07– 18.25” Lower Cross Tube ....... Qty. 1 ................... 125-5244-xx
08– Trolley Trunk Assembly (Y) .... Qty. 1 .............................................
TR18zz/xx ...................................................................... 835-5019-00
TT18zz/xx ...................................................................... 835-5402-00
Anthro® Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com
1-800-325-3841
SAVE THESE INSTRUCTIONS!
04
05
09– 12” Upper Cross Tube .......... Qty. 1 .................. 125-5243-00
10– Trolley Cable Wraps ................. Qty. 2 .................. 225-5756-00
1
11–
/4-20 Keps Nuts ........................ Qty. 6 .................. 325-5202-00
12– 18” Handle ................................. Qty. 1 .................. 125-5245-00
13– Shelf & Handle Side (X) ........Qty. 1 .................. 225-5754-00
14– 18.5” Wide Trolley Shelf .......... Qty. 1 .................. 100-6495-00
15– Shelf & Handle Side (Y) ........... Qty. 1 .................. 225-5755-00
3
16–
/4” Wood Screws ...................... Qty. 6 .................. 325-5106-00
17– 1/4-20 Button Head Screws ... Qty. 14 ................ 325-5210-00
18– 1/4-20 X 2” Handle Screws ....Qty. 2 .................. 325-5034-00
19– Non-Skid Pads (not shown) ...... Qty. 8 .................. 175-5068-03
06
November 2010, Rev H
Trolley Cart
Questions? 1-800-325-3841
Step 1
BEFORE YOU BEGIN, take special notice of the features on
the Swivel Lock Casters (those with the Green Brake Pedals).
The teeth on the plate of both Swivel Lock Casters need to
face the rear of the Trunk Assemblies.
Step 2 will give further instructions about securing the
Casters to the Trunk Assemblies.
Step 2 (requires the 3-Way Wrench)
STOP: IF YOU PURCHASED A TROLLEY BASE SHELF,
READ THOSE INSTRUCTIONS NOW.
Install all four Casters to both Trunk Assemblies using four
Button Head Screws per Caster.
DOUBLE CHECK THE INSTALLATION of the Swivel Lock
Casters (Green Brake Pedal) by positioning the Trunk Assembly
& Caster as shown. Then depress the Brake. If it is installed
correctly, the Caster will be locked in a parallel orientation (as
shown) with the Trunk Assembly.
NOTE: Make certain to install one Swivel Lock Caster (green brake)
and one Total Lock Caster (black brake) onto each
Trunk Assembly.
(5/16-18 X 3/4”) Button Head Screw
325-5188-00
NOTE: There are a matching
set of teeth on the truck.
Since the truck rotates, their
orientation is not critical.
Truck
Teeth
(on the Plates) faces the rear
of the Trunk Assemblies
Trunk Assembly (Y)
Rear of the Trunk
Assemblies
Swivel Lock Caster
(Green Brake Pedal)
rear position
Swivel Lock Caster
(Green Brake Pedal)
Plate
Installed to the
Trunk Assemblies
Total Lock Caster
(Black Brake Pedal)
front position
Step 4 (requires the 6mm Hex Key)
Rotate the Cart Assembly (from Step 3) onto the Casters.
Place the 12” Upper Cross Tube between each Trunk Assembly and align the Tube with the Large hole, midway
up the Trunk.
Carefully secure into place using one Tube Screw per end.
(5/16-18 X 1”) Tube Screw
325-5136-00
Step 5 (requires the 3-Way Wrench)
Position one Trolley Shelf & Handle Side against a Trunk
Assembly. Insert the two posts of a Side into holes 3 &
5 (from the top) of the Trunk. Loosely attach the Side to
the Trunk with one Button Head Screw and Keps Nut.
Repeat for the other Side.
Place the Trolley Handle between both Sides. Insert a
Handle Screw through both ends of the Side and carefully
thread into the Handle. Tighten the Button Head Screws
on the Sides.
NOTE: By installing the Side posts into holes 3 & 5, your nal
Shelf height will be 36” from the oor.
(1/4-20 X .375”) Button Head
Screw
325-5210-00
1
/4-20) Keps Nut
(
325-5202-00
1
/4-20 X 2”) Handle Screw
(
325-5034-00
Large hole
Shelf & Handle
Side (Y)
Button Head Screw
Keps Nut
Hole 3
Hole 5
12” Cross Tube
Shelf & Handle
Side (X)
Post
Handle Screw
Step 3 (requires the 6mm Hex Key)
Position both Trunk Assemblies and the 18” Lower Cross
Tube as shown.
Insert the 18” Cross Tube into the Large Holes of each
Trunk and loosely attach the Tube to each Trunk using one
Tube Screw per end.
NOTE: The 18” Cross Tube ends are keyed to t into the Trunk
Assemblies.
NOTE: If you purchased a Trolley Base Shelf, install the Casters
to the Trunk Assemblies during this Step.
(5/16-18 X 1”) Tube Screw
325-5136-00
Anthro® Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com
Large hole
Trunk Assembly (X)
Keyed Cross Tube
ends
Trunk Assembly (Y)
Step 6 (requires the 3-Way Wrench)
Determine the location for your Trolley Cable Hangers,
then position one against a Trunk Assembly.
Insert two Button Head Screws through the Cable Hanger
and capture on the opposite side using two Keps Nuts.
Repeat for remaining Cable Hanger.
1
(
/4-20 X .375”) Button Head
Screw
325-5210-00
1
/4-20) Keps Nut
(
325-5202-00
anthro.com
Trolley Handle and Shelf & Handle Side (Y)
are removed for clarity.
Button
Head
Screw
Hole 7
Hole 9
Cable Hanger
Shelf & Handle
Side (X)
Keps Nut
Loading...