Anthro MiniCart Assembly Instructions
Step 7
Install all four Caster Inserts into the Base Tube and
secure (fully tighten) with one Insert Screw per Insert.
Next, push the Casters, (locking ones in front) into the
Caster Inserts.
GLIDES ONLY
Thread each Glide
into the Glide Inserts
Insert Screw
(small pink patch on end)
325-5052-00
Step 8
Carefully rotate the Shelf Assembly (from Step 6),
upside down as shown.
Place the Base Tube Assembly (from Step 7) onto the
Vertical Legs of the Shelf Assembly.
Attach the Base Tube to each Leg using a total of three
Base Tube Screws.
Locking Casters
Anthro MiniCart
Assembly Instructions
These Assembly Instructions are
for the GT23xx.
Before beginning assembly of your
Anthro MiniCart, please take a moment
to review the parts listed below to verify
that your shipment is complete.
✔Does your Cart have 4" Casters?*
(Such as a GT23xx4. Your Caster Part
Numbers are given here.)
4" Non-Locking Caster
150-5010-03
4" Locking Caster
150-5011-03
TECHNOLOGY FURNITURE
14
13
11
12
10
08
09
®
Tighten all Support and Base Tube Screws.
Base Tube Screw
325-5000-00
Step 9
1.5" Small End Cap
Rotate your MiniCart over onto the Casters.
Pop the three 1.5" Small End Caps into the Vertical Legs
and the two 1.75" Large End Caps into the Base Tube.
Congratulations! Your MiniCart assembly is complete.
Please return the enclosed Registration Card to receive
our product updates, new catalogs, and sale flyers.
Thank you for choosing Anthro!
1.75" Large End Cap
*300-5385-00*
Questions? 1-800-325-3841
300-5385-00
✔Does your Cart have Glides?*
(Such as a GT23xxGL. Your Glide and Glide
Insert Part Numbers are given here.)
Glide Insert
525-1004-00
Glide
325-5042-00
Enclosed Parts List
Detailed views of all Hardware is provided with each Assembly Step
01 – Insert Screws ............................ Qty. 4.................325-5052-00
02– 2 3/8" Non-Locking Casters ........ Qty. 2 ...............150-5002-03*
03– Caster Inserts ........................... Qty. 4 ............... 525-1000-00*
04– 2 3/8" Locking Casters ................ Qty. 2 ...............150-5003-03*
05– 1.75" Large End Caps ............ Qty. 2 ..................175-5021-xx
06– Base Tube Screws ..................... Qty. 3 ................. 325-5000-00
07– MiniCart Base Tube ..................... Qty. 1 ..................125-5004-xx
08– Support Screws........................ Qty. 6 ................. 325-5010-00
09– Vertical Legs .............................. Qty. 3 .................. 125-5020-xx
10– Clamp Screws........................... Qty. 6 ................. 325-5086-00
11– Shelf Supports .......................... Qty. 6.................. 175-5060-xx
12– Shelf Clamps ............................. Qty. 6 ..................175-5059-xx
Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062
March 2006
SAVE THESE INSTRUCTIONS!
01
02
03
04
13– MiniCart Shelves ...................... Qty. 2 .................. 100-6003-xx
14– 1.5" Small End Caps ............... Qty. 3 ..................175-5020-xx
All Fastener quantities listed here are the minimum needed
for your Cart assembly. There may be a few extra
Fasteners included, which are not counted in the Parts List.
To make the assembly of your Anthro MiniCart even easier, we have included
all of the required tools (not shown above). The handy Hex Driver Bit can be
used in your electric drill in place of the Hex Driver.
Hex Driver 5/32" ........................ Qty. 1 ................. 375-5000-00
Hex Driver Bit 5/32" .................. Qty. 1 .................375-5003-00
8 oz. Rubber Mallet .................. Qty. 1 .................375-5022-00
05
07
06
Document # 300-5068-00
Anthro MiniCart
Assembly Instructions
Step 1
Before proceeding, please review the Assembly
Instructions of all Anthro Products you purchased
and are planning to include in this installation.
Questions? 1-800-325-3841
Overall MiniCart height is
28" using 2 3/8" Casters
Step 4
Loosely attach one Shelf to Hole 11 from the bottom (coped
end) of one Vertical Leg using a Support Screw.
NOTE: This will place your lower Shelf 19" from the floor using
the standard 2
3
/8" Casters.
NOTE: Add 1" to overall height for 4" Casters and
subtract 3" from overall height for Glides.
Step 2
Decide on the Shelf locations for your MiniCart. You can
place your Shelves almost anywhere on the Vertical Legs
(the Legs are stamped at 1" increments).
For a Lower Shelf location that is higher or lower than
19" from the floor, refer to the illustrations shown at right
to determine which holes to attach your Lower Shelf.
Once your MiniCart is assembled, it is very
difficult to move a Shelf without taking the
entire Cart apart and starting over.
NOTE: These instructions will place your Lower Shelf
19" from the floor using the standard 2
REMINDER: You may want to
measure your equipment to
make sure it fits between the
selected Shelf locations.
3
/8" Castors.
NOTE: These Instructions
will create approximately
8" of usable space between
your Shelves.
GT23xx
19"
GT23xx with 2 3/8" Casters
Lower Shelf
19"
GT23xx4 with 4" Casters
Hole 12=20"
Hole 11=19" (measured from the coped end)
Hole 10=18"
Coped end
Hole 11=20"
Hole 10=19"
Hole 9=18"
Hole 9=20"
Hole 8=19"
19"
GT23xxGL with Glides
Hole 7=18"
Insert one Support Screw
through each Shelf Support
Support Screw
325-5010-00
Step 5
Loosely attach the remaining Shelf to Hole 2 from the
top (non-coped end) of the Vertical Leg Assembly (from
Step 4) using one Support Screw.
NOTE: Handle the Shelf Assembly carefully until the Cart
is fully assembled.
Support Screw
325-5010-00
To p
(non-coped)
end
Hole 11=19"
(using 2 3/8" Casters)
Hole 2
Bottom
(coped)
end
Step 3
Attach three Shelf Supports to each Shelf.
Begin by first installing a Shelf Clamp into the Shelf
notch. Be sure the pointed barbs face towards the
outer Shelf edge.
Next, slide a Shelf Support into the recesses of the
Shelf Clamp and Shelf. Push in as far as possible.
Finally, secure with a Clamp Screw.
Clamp Screw
325-5086-00
Anthro Corporation Technology Furniture® 1 0450 SW Manhasset Drive Tualatin, Oregon 97062
First
Barbs
Next
Finally
Step 6
Loosely attach the 2nd and 3rd Vertical Legs to the
Shelf Assembly (from Step 5) using one Support
Screw per Shelf Support.
TIP: Use the holes in the Vertical Legs as a ruler to
ensure that your Support Screws are installed into the
correct locations.
Support Screw
325-5010-00
Bottom
(coped)
end
To p
(non-coped)
end
anthro.com
Loading...