Anthro eNook Standard II Assembly Instructions

ASSEMBLY INSTRUCTIONS

®

eNook

II

Part Number: EK3616zz/xx
NOTE: The eNook additional shelves shown above are not included.

Anthro Corporation® | 10450 SW Manhasset Dr. | Tualatin, OR 97062

Toll-free: 800.325.3841 | Fax: [phone] | email: [e-mail] | anthro.com

Outside the U.S. | Tel: [phone] | Fax: [phone]

January 2007

10

12

04

03

05

14

01

13

11

02

06

07

WELCOME

Thank you for purchasing eNook®!

This installation is a two person job.

If you have any questions or if we
can help you in any way, please
contact us at 800.325.3841.

NOTE: We provide do-it-yourself
hardware and instructions for
installation to wood studs and dry
wall. Your eNook can be mounted
to other surfaces (like concrete
and brick), and this work should be
done by a qualified contractor.

2

08

PARTS LIST

These instructions are for Anthro’s eNook.™ Before beginning
assembly, please take a moment to review the parts list below
to verify that your shipment is complete.

The following tools are required but not included:

¡ Power Drill
¡ 1/8" drill bit (for mounting to wood wall studs)
¡ 1/2" drill bit (for mounting to drywall)
¡ Phillips screwdriver (or Phillips bit for your drill)
¡ Level
¡ Stud Finder (for mounting to drywall)

Product Quantity Part Number

01 eNook Wall Frame 1 225-2247-23

02 6 Outlet Surge Protector 1 400-5190-06

03 1.5" Screws 4 325-5358-00

04 Workstation Screws 4 325-5092-00

05 3/8" Screw 1 325-5172-00

06 Cable Clips 6 175-5217-00

07 Toggle Bolt Dry Wall Anchor 4 325-5394-00

08 1-5/8" Screws 4 325-5086-00

09 Anthro Hex Driver (not shown) 1 375-5000-00

10 Cross Tray 1 225-2408-23

11 Main Unit 1 835-5200-xx

12 Pinch Cover 2 225-2418-23

13 Tack Board 1 100-6603-xx

14 Tack Clip 1 225-2424-23

STEP 1

14.75"
23"

Select the Mounting Location

¡ When choosing the right place to install your eNook, be sure to check the location of your power source. The power cord

that comes with your eNook is 6 ft long.

¡ Your eNook can be mounted to drywall or to wood wall studs. If you’re installing to wood wall studs, go to Step 2.

¡ If you’re installing into drywall, go to Step 7

STEP 2

Find Wall Studs

¡ Using a stud finder, locate the studs to which you'll attach your eNook.

STEP 3

Determine Mounting Point

¡ Determine the optimal desk height for your eNook.

Typical sitting height is about 29" high; typical
standing height is about 42" high.

¡ Measure up 14-3/4" from the shelf height and mark

that point on one stud.

STEP 4

Attach Screws to Wall Studs

¡ Using a 1/8" drill bit, drill one hole in a stud about

1-1/2" deep. How do you make sure that hole is
1-1/2" deep? Measure that length on your drill
bit and mark it with a piece of masking tape. Stop
drilling when you reach the masking tape.

1½"

Tape

Wall Stud Profile

Drill

¼"

Screw

¡ Using a Phillips driver (or a power driver with a

Phillips bit), attach the first 1-1/2" long screw at that
mounting point, but don’t tighten all the way to the
wall. Stop tightening when the screw head is about
1/4" away from wall.

eNook® Assembly Instructions

3