Anthro Elevate Original Single Surface Assembly Instructions
ASSEMBLY INSTRUCTIONS
TM
Elevate,
Electric Lift Table
Product Part#
36"w Single Surface ELTA136zz/xx4
48"w Single Surface ELTA148zz/xx4
60"w Single Surface ELTA160zz/xx4
72"w Single Surface ELTA172zz/xx4
Toll-free: 800.325.3841 | Fax: 800.325.0045 | email: sales@anthro.com | anthro.com
Anthro Corporation® | 10450 SW Manhasset Dr. | Tualatin, OR 97062
Outside the U.S. | Tel: 503.691.2556 | Fax: 503.691.2409
Rev F, January 2013
20
01
03
22
19
16
11
WELCOME
Thank you for purchasing Elevate,™ Electric Lift Table!
If you have any questions or if we can help you in any
way, please contact us at 800.325.3841.
This assembly requires two people.
PARTS LIST
Before beginning assembly of your Table, please
take a moment to review the parts listed below
to verify that your shipment is complete.
A Phillips head screwdriver is required
for this assembly.
Product Quantity Part Number
01 Shelf
36"w Elevate 1 100-6577-xx
48"w Elevate 1 100-6578-xx
60"w Elevate 1 100-6579-xx
72"w Elevate 1 100-6580-xx
02 Cross Tube
36"w Elevate 1 125-5277-zz
48"w Elevate 1 125-5184-zz
60"w Elevate 1 125-5185-zz
72"w Elevate 1 125-5186-zz
03 Shelf Gusset (X) 1 225-2269-zz
04 Shelf Gusset (Y) 1 225-2270-zz
2
13
07
21
10
05
12
08
02
09
Product Quantity Part Number
05 Cableway
36"w Elevate 1 225-2281-zz
48"w Elevate 1 225-2282-zz
60"w Elevate 1 225-2283-zz
72"w Elevate 1 225-2284-zz
06 Leg 2 575-5018-zz
07 Keypad Assembly 1
Keypad 400-5357-00
Keypad Slider 400-5358-00
08 Control Box 1 400-5393-00
09 Basetube 2 500-1005-zz
10 Cross Tube
36"w Elevate 1 500-1007-zz
48"w Elevate 1 500-1008-zz
60"w Elevate 1 500-1009-zz
72"w Elevate 1 500-1010-zz
11 4" Locking Caster 4 150-5065-00
12 Basetube End Cap 4 175-5158-32
13 Wire Management Clip 3 175-5188-00
14 Crosstube End Cap 2 175-5190-32
15 Velcro Tie (not shown) 2 175-5121-03
16 Basetube Washer 4
Black 225-2050-00
Silver Metallic 225-3522-00
17 3/4" Wood Screw 4 325-5106-00
18 3/8" Button Head Cap Screw 4 325-5149-00
19 4" Cap Screw 4 325-5166-00
17
04
14
18
06
(CONTINUED NEXT PAGE)
PARTS LIST (CONTINUED)
20 20mm Socket Head Cap Screw 16 325-5272-00
21 3/4" Phillips Screw 4 325-5370-00
22 1-1/4" Button Head Screw 16 325-5178-00
Product Quantity Part Number
23 Hex Driver (not shown) 1 375-5000-00
24 1/4" Hex Key (not shown) 1 375-5024-00
25 Rubber Mallet (not shown) 1 375-5022-00
STEP 1
Attach the Legs to the Base Tubes
¡ Hold one leg so the Slot is facing away from you and
the cord is coming out the top. Route the leg cord
through the notch on the top. Using the mallet, firmly
attach the cord grommet to the notch. Make sure that
one leg has the cord on the left and one leg has the
cord on the right.
¡ Align a leg with the opening on the base tube so that
the slot on the legs is facing the hole on the base tube
and that the cord comes out the top.
¡ Attach with four Socket Head Cap Screws.
26 5mm Hex Key (not shown) 1 375-5014-00
27 5/32" Hex Driver Bit (not shown) 1 375-5003-00
28 10’ Power Cord (not shown) 1 400-5181-00
Product Quantity Part Number
For 36” and 48” wide Elevates
29 1-meter Control Box Cable (not shown) 2 400-5182-00
For 60” and 72” wide Elevates
30 1-meter Control Box Cable (not shown) 1 400-5182-00
31 2-meter Control Box Cable (not shown) 1 400-5180-00
Slot
Leg
Hole
Rear
¡ Repeat for the second leg.
Cord Grommet
Basetube
Front
20mm Socket Head Cap Screw
325-5272-00
Notch
Elevate,TM Electric Lift Table Assembly Instructions
3
Loading...