Anthro AnthroBench II 72 Assembly Instructions
Step 7
Place the Bench Shelf (laminate facing down) onto the floor.
With the help of another person, carefully rotate the Base Assembly
(from Step 6) over onto the Shelf.
Position the holes on the Pans and Arms to align with the twelve
predrilled holes on the Shelf. Insert two 1” Button-hd PB Screws
through each center opening of the Bench Pans (shown encircled at
right).
Install the remaining PB Screws into each of the Arms and Pans. A
total of twelve PB Screws will be installed.
If a drawer and/or keyboard caddy are a part of this configuration,
install them now using their instructions. If the 5” casters upgrade is
part of this configuration, remove the glides and install the casters now.
With the help of a buddy, carefully rotate your AnthroBench right side
up.
1” Button Hd PB Screw
325-5580-00
Step 8 (requires a 3-Way Wrench)
FIRST- from the rear of your Bench, align one Buttress with
one hole on the Back Pan. Install a Pan Screw through the
Buttress and loosely capture using a Keps Nut on the opposite
side.
SECOND- position one Cross End on the remaining Buttress
end and install a Pan Screw and Keps Nut in the same manner,
but do not fully tighten.
THIRD- rotate the Buttress to align the Cross End with two
openings on the Leg. Secure the Cross End to the Leg using
two Support Screws.
Repeat this entire procedure for the remaining Buttress and
Cross End on the opposite end.
Tighten all Pan Screws, Support Screws and Keps Nuts.
Back Pan hole
FIRST Install this Pan Screw
Arms
Rounded Edge of Shelf
THIRD Install the Cross End
Pans
Predrilled holes
Buttress
72” AnthroBench II
Assembly Instructions
TECHNOLOGY FURNITURE
These Assembly Instructions are for the 72” AnthroBench models. Before beginning assembly of your AnthroBench, please
take a moment to review the parts listed below to verify that your shipment is complete.
Your AnthroBench is heavy!
Don’t try to lift it yourself. Work with
a buddy.
06
07
08
09
03
02
01
18
05
19
13
14
15
16
04
12
11
10
Enclosed Parts List
Detailed views of all Hardware is provided with each Assembly Step
®
20
17
21
22
Congratulations! Your AnthroBench assembly is complete.
Please return the enclosed Registration Card to receive product
SECOND Install this Pan Screw
updates!
Thank you for choosing Anthro!
NOTE: The purpose of the Buttress is not to support your Bench Shelf. It is intended to make
your Bench absolutely rigid under extreme weight
conditions.
(1/4-20 X .5”) Pan Screw
325-5003-00
(1/4-20) Keps Nut
325-5130-03
Support Screw
325-5010-00
Removal of Leg Covers and Cable Grommets
Remove the Leg Cover by: 1. Using the Anthro driver, remove
the top two Workstation Screws. 2. Lift and tilt the Cover up
and free of the lower metal mounts.
Cable Grommets are snapped into and out of each of the
circular Leg openings.
300-5599-00
Questions? 1-800-325-3841
300-5599-00
Workstation Screw
(not counted in Parts List)
325-5092-00
Cable Grommet
Lower Metal Mounts
01– 30” Wide Bench Shelf .............Qty. 1 ................(see below)
28” Deep (ABS7229zz-xx and ABS7235zz-xx) 101-1126-00-00
36” Deep (ABD7229zz-xx and ABD7235zz-xx) 101-1119-00-00
02– Bench Leg Assemblies .............Qty. 2 .................(see below)
25” Bench Legs (ABS7229zz-xx and ABD7229zz-xx) 835-5008-00
31” Bench Legs (ABS7235zz-xx and ABD7235zz-xx) 835-5009-00
03– Bench Arm Left ........................Qty. 1 ............225-5357-00
04– Cross Ends .................................Qty. 2 ...........225-5334-00
05– 1” Button-hd PB Screws .........Qty. 12 ..........325-5580-00
06– Glide Insert Screws ..................Qty. 4 ............325-5052-00
07– 2.5” End Caps ............................Qty. 4 ...........175-5158-00
08– Glide Inserts ..............................Qty. 4 ............525-5030-00
09– Glides (1/2-13 X 2”) ...................Qty. 4 ............325-5165-00*
10– Cap Screws (5/16-18 X 4”) ........Qty. 8 ............ 325-5166-00
11– Curved Washers ........................Qty. 8 225-2050-00 or 225-3522-00
12– Bench Base Tubes .....................Qty. 2 .................(see below)
28” Deep (ABS7229zz-xx and ABS7235zz-xx) ......125-5225-00
36” Deep (ABD7229zz-xx and ABD7235zz-xx) .....125-5183-00
Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062
November 2013
SAVE THESE INSTRUCTIONS!
13– 20” Bench Buttress ..................Qty. 2 ............225-5388-00
14– 65.5” Bench Cross Tubes ........Qty. 2 ............125-5186-00
15– Keps Nuts (1/4-20) ....................Qty. 8 ............325-5130-00
16– Pan Screws (1/4-20 X .5”) ........Qty. 8 ............325-5003-00
17– Bench Arm Right ......................Qty. 1 ............225-5358-00
18– Support Screws ........................Qty. 20 .......... 325-5010-00
19– 72” Bench Pans .........................Qty. 2 ............225-5372-00
All Screw quantities listed here are the minimum needed
for your Bench assembly. There may be a few extra Screws
included, which are not counted in the Parts List.
To make the assembly of your Anthro Bench even easier, we
have included the required tools. The handy Hex Driver Bit
can be used in your electric drill in place of the Hex Driver.
20 - Hex Driver 5/32” .........................Qty. 1 ............375-5000-00
21 - Hex Driver Bit 5/32” ...................Qty. 1 ............375-5003-00
22 - Hex Key 1/4” ...............................Qty. 1 ............375-5024-00
3-Way Wrench (not shown) ..........Qty. 1 ............225-5196-03
anthro.com
72” AnthroBench
Assembly Instructions
Step 1
Install two Bench Glide Inserts into each Bench Base Tube and
secure with one Insert Screw per Insert.
Pop two End Caps into the ends of both Base Tubes.
Insert Screw
(small pink patch on end)
325-5052-00
Questions? 1-800-325-3841
Leave these two holes open
Glide Inserts placed into
the large holes
Step 4
Determine the desired height of your Shelf. This instructions will
place the shelf at the top of the legs, either 29” or 35” from the
floor (depending on which height Bench you purchased). If you
install 5” casters on your bench, they’ll make your Bench 5” taller.
The holes along the Leg Assemblies are spaced at 1” increments.
Adjusting either one hole up or down will modify the final Shelf
height by 1” respectively. Rotating the Glides will also provide
additional height adjustment.
NOTE: Your Shelf height can be adjusted at a later time if needed
by following Steps 5-8 below.
29” or 35”
REMINDER: You may want to measure your
equipment to make sure it fits into the
selected Shelf location.
Step 2
Orient one Bench Leg Assembly with one Base Tube Assembly
(from Step 1). The Glide Inserts should be facing down.
Insert one Bench Cap Screw through one Curved Washer, then
carefully insert through one of the lower holes on the Base
Tube, threading into the Right Leg Assembly.
Repeat this procedure for the remaining three lower holes on
the Right and Left Leg Assembly.
If you are installing Bench Glides, install them now by
threading one into each Glide Insert. If you are upgrading
to 5” Casters, install them now following their enclosed
instructions.
(5/16-18 X 4”) Bench Cap Screw
325-5166-00
Curved Washer
225-2050-00 or 225-3522-00
Step 3
Position the Right Leg Assembly (from Step 2) with two
Cross Tubes as shown. Insert one Bench Cap Screw with a
Curved Washer through a side hole, carefully threading the
Screw into the Cross Tube.
Repeat entire procedure for the remaining three
side holes.
NOTE: Loosen these
Support Screws (if
needed) to allow the
Base Tube to install
easier.
Thread one Glide
into each Glide Insert
AFTER the Base
Tubes have been
installed to the Legs.
Left Leg Assembly
Left Leg
Assembly
Glide Inserts
Lower holes
Leave these two holes open
Right Leg
Assembly
Cross Tubes
Step 5
Position the Left Bench Arm onto the Left Leg Assembly.
Align the top two openings of the Arm with hole 2 of the Leg
Assembly. Loosely install a Support Screw through the top
two holes of the Arm into the Leg.
Install the remaining six Support Screws into the Left Arm,
but do not fully tighten any of the Support Screws.
Repeat entire procedure for the Right Bench Arm on the Right
Leg Assembly.
Support Screw
325-5010-00
Step 6 (requires a 3-Way Wrench)
Position a Bench Pan between the Arms, aligning the two
tabs on each Arm with the two holes in the lower corners
of a Pan. Insert a Pan Screw through the Pan and Arm
Tab capturing it with a Keps Nut (but do not fully tighten).
Repeat this procedure for the remaining end of the Pan and
for the second Pan.
Tighten all Pan and Support Screws.
Leave top two
holes open
Left Leg Assembly
Arms
Hole 2
Left Bench Arm
Right Leg Assembly
(5/16-18 X 4”) Bench Cap Screw
325-5166-00
Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062
Curved Washer
225-2050-00 or 225-3522-00
Right Leg Assembly
Side holes
NOTE: the 3-Way Wrench can be used to assist in
tightening the Keps Nuts.
(1/4-20 X .5”) Pan Screw
325-5003-00
(1/4-20) Keps Nut
325-5130-03
Second Pan shown installed
anthro.com
Loading...