
00:00 a.m. (midnight) – 08:00 p.m. (CST), Monday – Friday
06:00 a.m. – 02:00 a.m. (GMT), Monday – Friday.
00:00 a.m. (midnight) – 02:00 p.m. (CST), Monday – Friday
06:00 a.m. – 08:00 p.m. (GMT), Monday – Friday.
If you’re trying to reach us outside working hours, we advise you to file a ticket in our customer support system or leave a
Enter your search term here...
Modified on: Wed, 24 Oct, 2018 at 10:12 AM
1 of 10

Edge Solo is a high-quality single-capsule large-diaphragm condenser microphone by Antelope Audio. Combined with
Antelope’s cutting-edge modelling technology, it allows users to emulate 18 of the world’s most iconic vintage
microphones with uncanny accuracy. !The Edge Solo features modelling that was performed in one of the most respected
facilities in Germany using an exquisitely preserved collection of classic microphones.
Phantom power – ensure phantom power supply is 48V.
2 of 10

The solo has a standard 3 pin XLR output so any microphone cable is sufficient for the job. Just connect the mic with one
of the designated emulation-ready preamps and you are good to go.
4. Claim and assignfeatures
http://www.antelopeaudio.com
Enter your credentials and password
Navigate to Claim Features
Enter the voucher code ME*****, mark the check box on the End Users License Agreement and click “Claim”
Open the interfaces Control Panel and go to the Help tab (the “?” button)
Open the Administration panel
Mark “Register device and assign features” and continue
Mark the checkbox with the Microphone Emulations and continue
The device will restart, and your new Mic Emulations will be available.
5. Load a Mic Emulation in your Antelope Audio Interface.
Open the interface Control Panel and click on the little settings icon on the preamp gain control.
To have access to the mic settings, the input should be in Mic mode.
When you load a Mic Emulation the following screen will pop up.
3 of 10

48V Phantom power will be automatically enabled.
Thefollowing controls are available on the pop-up window once you choosethe Edge Solo:
!– allows you to invert the polar pattern of the signal in the selected Mic input.
4 of 10

!– is switched on by default, when you’re loading a Mic Emulation in the Antelope Audio interface
– allows you to switch between Verge and Edge mic types or turn the emulation off.
5 of 10

!– here you can choose the exact model of the mic you wish to emulate.
6 of 10

In order to record the emulated signal,you must choose the following routing scheme.
Choose EMU MIC with the corresponding channels for the mic inputs. This way you will record the processed signal with
the loaded emulation. You can also choose a mix on emulated and dry preamp signal, with a combination of a couple of
channels (Emu and Preamp)
Zen Tour, Orion Studio 2017, Goliath, Goliath HD
Inside the routing tab, there is a strip: Emulated Mic, which corresponds to the physical inputs where you can connect the
In order to record the emulations, just drag and drop the channels you are using from the Emulated Mic strip, to the
Record strip (dependent on the type of communication – USB or Thunderbolt).
Again, you can record dry and wet signal with a combination of the Emulated mic channels!
and the physical input
channels.
7 of 10

7. Technical Specifications
Large condenser, single-sided 6u gold-sputtered membrane
-35dB | 18mV/Pa (-1 to +3dB)
Not included (standard 3-pin XLR cable)
8 of 10

Can be transformed into a vintage replica via the Antelope Audio Mic Emulation Packs.
BerlinV563 cardioid capsule
Having difficulties with the Edge Solo microphone or anything else Antelope?Get in touch with us by the following means:
European Direct Support Line
10:00 a.m. – 10:00 p.m. (EET), Monday – Friday
7:00a.m. – 6:30 p.m. (EST), Monday – Friday
Online(live chat and e-mail)
AntelopeAudio Support Page
https://en.antelopeaudio.com/support/
9 of 10