Ansell Lighting ATORLED2/110V Installation Instructions

Description – Tornado IP65 110V LED Non-Corrosive
® Installation Instructions
Luminaire Code(s) - ATORLED_ _/110V
General Installation Instructions These instructions should be read carefully prior to any installation and retained after completion for further reference and maintenance. Please give these instructions to the building owner/occupier after installation.
Important Safety
1. Before installation, maintenance or lamp replacement, ensure that the mains supply to the luminaire is switched off and the circuit
supply fuses are removed or the circuit breaker is turned off.
2. It is recommended that only a qualified electrical contractor carries out the installation of this luminaire and that the luminaire is installed in compliance with the current edition of the IEE Wiring Regulations.
3. The person carrying out the installation is to check and verify that the total load on the circuit, including that of this luminaire does not exceed the rating of the circuit cable, fuse or circuit breaker.
4. Where a luminaire incorporates discharge control gear (inductive load), the circuit capacity and ratings require careful sizing to avoid nuisance tripping of the protective device used in the installation.
5. Where applicable, careful consideration should be taken during installation to ensure that all fixings and/or suspensions are of a suitable size for the luminaire being installed.
Ratings
1. All luminaires are manufactured & tested in compliance with the requirement contained within BS EN 60598 and are CE marked.
3. All luminaires that are of Class 1 construction and that are marked accordingly, MUST be earthed.
3. All luminaires are designed to operate at 110 AC -6%/+10% Do not operate outside these voltages.
4. All luminaires are only suitable for applications within their rated Ingress Protection limits as stated.
Exclusions to Warranty Please Note - The limited warranty shall be null and void in the following circumstances:-
Failure by the installer, end user or any third party to exercise caution to protect any covered product or part from outside damage, adverse temperature (normal operating ambient temperature -10°C to 40°C), humidity conditions, fluctuations in the electrical system or physical abuse as well as failure related to workmanship in the installation of the products or parts.
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­Page No. 1 Ansell Lighting Products, Unit 6B, Stonecross Ind. Park, Yew Tree Way, Warrington, WA3 3JD www.anselluk.com
DO NOT DRILL THE BODY OF THIS LUMINAIRE FOR MOUNTING PURPOSES. THE LUMINAIRE IS ONLY DESIGNED FOR
INSTALLATION, USING THE CLIPS AND HOOKS PROVIDED AND ONLY AT THE FIXING POINTS OF THE FITTING. ANY DRILLED
HOLES DURING INSTALLATION WILL ALSO INVALIDATE THE IP RATING OF THE FITTING.
Installation
Determine the fixing centres from the sizes indicated on the box or from the table below.
If mounting to ceilings, securely fix the stainless steel mounting clips using screw fixings provided at the spacing's mentioned above. For suspended mounting, use hanging
hooks provided on the back of the fitting.
Remove the front diffuser by unhinging stainless steel clips and gear tray assembly and place in a safe place until needed.
Select a suitable cable entry point by drilling into the base at any of the 20mm entry points. (Suitable provision MUST be made to protect IP rating of luminaire).
It is the installer’s responsibility to provide adequate electrical connections to maintain the correct IP rating for the installed environment. This is in accordance to BS EN
7671.
Use only circular H05RN-F 3*1mm2. Ensure the cable entry connector has a minimum water ingress rating of IPX5.
Electrical Connections
Connect as follows:- LIVE (L) BROWN OR RED (switched)
NEUTRAL (N) BLUE OR BLACK EARTH GREEN / YELLOW
Terminate the supply cable ensuring correct polarity is observed and the luminaire MUST be earthed.
Replace the gear tray into the clips.
Seat diffuser against gasket, fit clips into recess points in base and secure diffuser with clips.
Lock the clips into the closed position by using the fixing screw supplied.
Restore supply for satisfactory operation.
Note :- It is the responsibility of the installer/specifier to determine the suitability of this luminaire for the application. Luminaire types with high IP rating protection
may not be suitable for installations with prolonged daily use due to accumulative heat not being able to dissipate from the luminaire body, affecting life
span of components.
®
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Maintenance:
1. If replacing the LED Driver, please ensure the driver is the correct sized housing and the secondary output / wattage has the same specification as that detailed in the table above.
2. The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
Blue / Black
Brown / Red
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Page No. 2 Ansell Lighting Products, Unit 6B, Stonecross Ind. Park, Yew Tree Way, Warrington, WA3 3JD www.anselluk.com
Disposal of Electronic Equipment WEEE Directive 2002/96/EC
This product falls within the scope of the Waste Electrical & Electronic Equipment Directive (WEEE), which means the product should not be disposed of as normal household waste. Ensure that this luminaire and lamp is disposed of in accordance with the WEEE Directive. Contact a local Council Waste Dept. Local Amenity Site, or the Environment Agency for further information. RoHS - All components and materials used in this product are RoHS 2002/95/EC compliant.
Operating Conditions
Tornado 110V LED
This luminaire is designed to operate in a temperature range -10oC to +40oC
Loading...