®
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------Page No. 1 Ansell Lighting Products, Unit 6B, Stonecross Ind. Park, Yew Tree Way, Warrington, WA3 3JD www.anselluk.com
Issue 1.0
Description – Mira 2 Asymmetrical Floodlight
Installation Instructions
Luminaire Code(s) – AM2LED/ASY/___
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
General Installation Instructions
These instructions should be read carefully prior to any installation and retained after completion for further
reference and maintenance. Please give these instructions to the building owner/occupier after installation.
Important Safety
1. Before installation, maintenance or lamp replacement, ensure that the mains supply to the luminaire is switched off and the
circuit supply fuses are removed or the circuit breaker is turned off.
2. It is recommended that only a qualified electrical contractor carries out the installation of this luminaire and that the
luminaire is installed in compliance with the current edition of the IEE Wiring Regulations.
3. The person carrying out the installation is to check and verify that the total load on the circuit, including that of this luminaire
does not exceed the rating of the circuit cable, fuse or circuit breaker.
4. Where a luminaire incorporates discharge control gear (inductive load), the circuit capacity and ratings require careful
sizing to avoid nuisance tripping of the protective device used in the installation.
5. Where applicable, careful consideration should be taken during installation to ensure that all fixings and/or suspensions are
of a suitable size for the luminaire being installed.
Ratings
1. All luminaires are manufactured & tested in compliance with the requirement contained within BS EN 60598 and are CE marked.
2. All luminaires that are of Class 1 construction and that are marked accordingly, MUST be earthed.
3. All luminaires are designed to operate at 230Volts AC -6% / +10% = 216Volts to 253Volts. Do not operate outside these voltages.
4. All luminaires are only suitable for applications within their rated Ingress Protection limits as stated.
5. Ambient temperature -20°C to 50°C.
All model dimensions as above diagram.
Model
Power (W)
Weight (kg)
AM2LED/ASY/500
500
22.0kg
AM2LED/ASY/800
800
24.3kg
®
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------Page No. 2 Ansell Lighting Products, Unit 6B, Stonecross Ind. Park, Yew Tree Way, Warrington, WA3 3JD www.anselluk.com
Issue 1.0
Installation
• This luminaire contains no serviceable or replaceable parts.
• The external flexible cable or cord of this luminaire cannot be replaced, if the cord is damaged the luminaire shall be
replaced.
• The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall
be replaced
• If the glass becomes cracked or broken please ensure that the luminaire is replaced.
• The fitting is suitable for fixing to the wall and to the ceiling.
• Please observe the minimum mounting distance of 5 metres from surfaces being lit.
• The fitting has an earthing connection. The earth wire (green/yellow) has to be secured to the correct location marked .
• It is the installer’s responsibility to ensure all connections and seals provide adequate IP ratings as per BS EN 7671 – 17th
Edition Wiring Regulations.
• Please note this luminaire is supplied pre-wired with 1.0m of H05RR-F 3G1.5mm2 cable.
• Adequate clearance must be allowed between any point on the rear of the luminaire & the surface above in order to allow
for adequate air circulation.
• Please take care as sections of this luminaire can become very hot when under use.
Please cut off the main power before installation and maintenance
Lamps are not allowed to be covered with combustible materials
2. Mount luminaire on desired suitable surface ensuring secure fitment.
3. Connect luminaire to circuit ensuring correct polarity.
1. Turn the luminaire over +90° and set bracket to desired angle.
2 x M10
17mm A/F
4 x M10
17mm A/F
Loading...