Ansell Lighting ADSILED2/M3, ADSILED2/MWS, ADSILED2/MWS/M3, ADSILED2 Installation Instructions

Description – Disco Slim LED IP65

Disposal of Electronic Equipment WEEE Directive 2002/96/EC

This product falls within the scope of the Waste Electrical & Electronic Equipment Directive
(WEEE), which means the product should not be disposed of as normal household waste.
Ensure that this luminaire and lamp is disposed of in accordance with the WEEE Directive.
Contact a local Council Waste Dept. Local Amenity Site, or the Environment Agency for
further information. RoHS - All components and materials used in this product are RoHS
2002/95/EC compliant.

Installation Instructions

Luminaire Code(s) – ADSILED2 and 2/WW

General Installation Instructions
These instructions should be read carefully prior to any installation and retained after completion for further
reference and maintenance. Please give these instructions to the building owner/occupier after installation.

Important Safety

1. Before installation, maintenance or lamp replacement, ensure that the mains supply to the luminaire is switched

off and the circuit supply fuses are removed or the circuit breaker is turned off.

2. It is recommended that only a qualified electrical contractor carries out the installation of this luminaire and that
the luminaire is installed in compliance with the current edition of the IEE Wiring Regulations.

3. The person carrying out the installation is to check and verify that the total load on the circuit, including that of this
luminaire does not exceed the rating of the circuit cable, fuse or circuit breaker.

4. Where a luminaire incorporates discharge control gear (inductive load), the circuit capacity and ratings require
careful sizing to avoid nuisance tripping of the protective device used in the installation.

5. Where applicable, careful consideration should be taken during installation to ensure that all fixings and/or

Ratings

1. All luminaires are manufactured & tested in compliance with the requirement contained within BS EN 60598 and are CE marked.

2. All luminaires that are of Class 1 construction and that are marked accordingly, MUST be earthed.

3. All luminaires are designed to operate at 230Volts AC -6%/+10% = 216Volts to 252Volts. Do not operate outside these voltages.

4. All luminaires are only suitable for applications within their rated Ingress Protection limits as stated.

Exclusions to Warranty
Please Note - The limited warranty shall be null and void in the following circumstances:-

Failure by the installer, end user or any third party to exercise caution to protect any covered product or part from outside
damage, adverse temperature (normal operating ambient temperature -10 - 50°C), humidity conditions, fluctuations in the
electrical system or physical abuse as well as failure related to workmanship in the installation of the products or parts.

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Installation

suspensions are of a suitable size for the luminaire being installed.

 Remove the diffuser from the base by rotating anti-clockwise. Unscrew the three retaining screws and rotate the gear tray to remove.
 Carefully remove the knock-out (20mm cable entry and Besa mountings at centre of the base).
 Position and fix the base to a suitable solid surface using screws supplied, sealant should be applied around the screw heads to reduce

water ingress if the luminaire is to be mounted externally (Luminaires should not be installed where the illuminated surface is within 0.5m
from the front of the fitting). NOTE: If mounting on a BESA conduit box, a suitable gasket (rubber) should be used.

 Secure supply cable into the luminaire through cable entry ensuring that a cable gland, grommet or sealing compound is used to maintain

the IP rating of the luminaire.

 Terminate the cable into the terminals ensuring correct polarity is observed.
 Please see below for electrical connections.

Electrical Connections

Connect as follows :- LIVE (L) BROWN OR RED (switched)

 Re-attach the gear tray back into position.
 Re-fit the diffuser, taking care to ensure it is properly seated.

NEUTRAL (N) BLUE OR BLACK
EARTH GREEN & YELLOW

 Restore power supply, switch on and test for satisfactory operation.

IP65

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­Maintenance:

1. This luminaire contains no serviceable parts.

Blue / Black

Brown / Red

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Ansell Electrical Products, Unit 6B, Stonecross Ind. Park, Yew Tree Way, Warrington, WA3 3JD www.anselluk.com