Datasheet APL5901-13VC-TR, APL5901-13DC-TR, APL5901-13D5C-TR, APL5902-34VC-TR, APL5902-34U5C-TR Datasheet (ANPEC)
...
Low IQ, Low Dropout 900mA Fixed Voltage Regulator
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw1
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise
customers to obtain the latest version of relevant information to verify before placing orders.
Features
Design with an internal P-channel MOSFET pass
transistor, the APL5901/2 maintains a low supply
current, independent of the load current and dropout
voltage. Other features include reverse current
protection, thermal-shutdown protection, current limit
protection to ensure specified output current and controlled short-circuit current. The APL5901/2 regulator
come in a miniature SOT-89, SOT-89-5, SOT-223, SO8, TO-252 and TO-252-5 packages.
Applications
• Notebook Computer
• PDA or Portable Equipments
• Noise-Sensitive Instrumentation Systems
••
••
• Low Noise : 50µV
RMS
(100Hz to 100kHz)
••
••
• Low Quiescent Current : 50µA (No load)
••
••
• Low Dropout Voltage : 210mV (@900mA)
••
••
• Very low Shutdown Current : < 1µA
••
••
• Fixed Output Voltage : 1.3V ~ 3.4V
••
••
• Stable with 4.7µF Output Capacitor
••
••
• Stable with Aluminum , Tantalum or Ceramic
Capacitors .
••
••
• Reverse Current Protection
••
••
• No Protection Diodes Needed
••
••
• Built in Thermal Protection
••
••
• Built in Current Limit Protection
••
••
• Controlled Short Circuit Current : 200mA
••
••
• Fast Transient Response
••
••
• Short Setting Time
••
••
• SOT-89, SOT-89-5, SOT-223, SO-8 ,TO-252
and TO-252-5 Packages
Pin Configuration
SOT-89 (T op View)
V
IN
GND V
OUT
123
TAB is GND
SO-8 (T op V iew)
SOT-223 (T op View)
1
2
3
45
6
7
8IN
GND
GND
SHDN BYP
GND
GND
OUT
V
OUT
GNDV
IN
123
TAB is GND
TO-252-5 (T op View)
TAB is GND
123
V
OUT
V
IN
General Description
The APL5901/2 is micropower, low noise, low dropout
linear regulator. Operate from 2.7V to 6V input voltage
and deliver up to 900mA. Typical output noise is just
50µV
RMS
with the addition of an external 0.1µF bypass capacitor in BP pin and typical dropout voltage
is only 210mV at 900mA loading. Designed for use in
battery-powered system, the low 50µA quiescent current makes it an ideal choice.
TO-252 (T op V iew)
APL5901
BP
V
OUT
GND
V
IN
12345
TAB is GND
SHDN
SOT-89-5 (T op View)
V
IN
GND
V
OUT
123
54
SHDN
BP
GND
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw2
Package Code
D : S OT -8 9 D 5 : S OT -8 9-5 U : T O -2 5 2
U5 : TO-252-5 V : SO T-223 K : SO-8
Tem p. Range
C : 0 to 70 C
Handling Code
TR : Tape & Reel
Voltage Code :
13 : 1.3V ~ 34 : 3.4V
APL5901/2 -
Handling Code
Tem p. Range
Package Code
Voltage Code
APL5901/2
XXXXX13
APL5901/2 - 13 D/V/K :
XXXXX - Date Code , 13 - 1.3V
13
APL5901/2
XXXXX
APL5901/2 - 13 U :
XXXXX - Date Code , 13 - 1.3V
Pin Description
PIN
No. Name
I/O Description
1VINI Supply voltage input.
2GND
Ground pins of the circuitry, and all ground pins must be soldered to
PCB with proper power dissipation.
3 SHDN
(Note1)
I Shutdown control pin, low = off , high = normal .
4BP
(Note1)
O Bypass signal pin in fixed output type device
5V
OUT
O Output pin of the regulator.
Ordering and Marking Information
Pin Configuration (Cont.)
SOT-223 (T op View)
V
IN
V
OUT
GND
123
TAB is V
OUT
APL5902
°
Note1 : These pins do not exist in 3-pin package.
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw3
Unless otherwise noted these specifications apply over full temperature, VIN=3.6V, CIN=1µF, COUT=4.7µF,
SHDN=VIN, TJ=0 to 125°C. Typical values refer to TJ=25°C.
Symbol Parameter Rating Unit
VIN, V
OUT
Input Voltage or Out Voltage 6 V
SHDN
Shutdown Control Pin
6V
R
TH,JA
Thermal Resistance – Junction to Ambient
SOT-89 : 180
SOT-223 : 135
SO-8 : 150
TO-252 : 50
°
C/W
P
D
Power D iss ipa tion Internally Li m ited W
T
J
Operating Junction Tem p erature
°
C
Control Section 0 to 125
Power Transistor 0 to 150
T
STG
Storage Temperature Range -65 to +150
°
C
T
L
Lead Temperature (Soldering, 10 second) 260
°
C
Absolute Maximum Ratings
Electrical Characteristics
APL5901/2
Symbol Parameter Test Conditions
Min. Typ. Max.
Unit
V
IN
Input Voltage 2.7 6 V
V
OUT
Output Voltage V
OUT
+1.0V< VCC<6.0V, 0mA< I
OUT
< I
MAX
V
OUT
-2
%
V
OUT
V
OUT
+2
%
V
I
LIMIT
Circuit Current Limit
V
IN
=4.3V
1.5 A
I
SHORT
Short Current V
OUT
=0V 200 mA
I
OUT
Load Current
900 mA
REG
LINE
Line Regulation V
OUT
+0.5V< VCC<6.0V, 0mA< I
OUT
< I
MAX
410mV
REG
LOAD
Load Regulation VIN =V
OUT
+1.0V, 0mA< I
OUT
< I
MAX
1
6
mV
V
DROP
Dropout Voltage
(Note2)
(V
OUT
(Nominal)=3.0V
Version)
I
OUT
=900mA
210 300 mV
PSRR Ripple Rejection
F≤1kHz, 1Vpp at V
IN
= V
OUT
+1.0V
55 65 dB
No load 50 100
I
Q
Quiescent Current
I
OUT
=900mA 370 450
µ
A
Shutdown Supply
Current
(Note3)
Shutdown = low
I
OUT
=0, VCC =6.0V
0.01 1
µ
A
100Hz<f<100kHz, typical load,
C
BP
=0.01µF, C
OUT
= 1µF
50
Noise
(Note3)
100Hz<f<100kHz, typical load,
C
BP
=0.1µF, C
OUT
= 1µF
40
µ
Vrms
CBP=0.01µF,C
OUT
=1µF, no load 7
Shutdown Recovery
Delay
(Note3)
CBP=0.1µF,C
OUT
=1µF, no load 70
ms
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw4
APL5901/2
Symbol Parameter Test Conditions
Min. Typ. Max.
Unit
OTS
Over Temperature
Shutdown
150
°
C
Over Temperature
Shutdown Hysteresis
Hysteries 10
°
C
TC
Output Voltage
Temperature
Coefficient
50 ppm/°C
C
OUT
Output Capacitor 4.2 4.7 5.2
µ
F
ESR 0.02 0.1 1 Ohm
Shutdown Input
Threshold
(Note3)
V
OUT
+1.0V< VIN <6.0V 0.4 0.7 1.6 V
I
SHDN
Shutdown input Bias
current
(Note3)
V
SHDN
=V
IN
0.01 100 nA
Input Reverse Leakage
current
V
OUT-VIN
=0.1V 0.1 0.5
µ
A
Reverse Protection
Threshold
11 50 mV
Application Circuit
BP
V
OUT
V
IN
GND
SHDN
VOUT
C
IN
1µF
off
on
APL5901
INP UT
2.7V to 6V
0.1
µ
FC
BP
C
OUT
4.7µF
Electrical Characteristics (Cont.)
Note 2 : Dropout voltage definition : VIN-VOUT when VOUT is 2% below the value of VOUT for VIN = VOUT + 0.5V
Note 3 : For 5-pin devices only.
Unless otherwise noted these specifications apply over full temperature, V
IN=3.6V, CIN=1µF, COUT=4.7µF,
SHDN=VIN, TJ=0 to 125°C. Typical values refer to TJ=25°C.
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw5
APL5901/2-33
APL5901/2-33
APL5901/2-33
0
0.5
1
1.5
2
2.5
3
3.5
0123456
0
50
100
150
200
250
300
350
0123456
0
50
100
150
200
250
300
350
400
0 150 3 00 450 600 750 900
0
0.5
1
1.5
2
2.5
3
3.5 4 4.5 5 5.5 6
Typical Characteristics
Current Limit vs. Input Voltage
Input Voltage (V)
Current Limit (mA)
Ground Pin Current vs. Output Current
Ground Pin Current vs. Load Current (uA)
Output Current (mA)
Ground Pin Current vs. Input Voltage
Input Voltage (V)
Ground Pin Current vs. Load Current (uA)
Input Voltage vs. Output V oltage
Input Voltage (V)
Output Voltage (V)
APL5901/2-33
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw6
APL5901/2-33
APL5901/2-33
-100
+0
-90
-80
-70
-60
-50
-40
-30
-20
-10
20
200k50 100 200 500
1k 2k 5k 10k 20k
50k 100k
0.4
0.5
0.6
0.7
0.8
0.9
1
3 3.5 4 4.5 5 5.5 6
-12
-10
-8
-6
-4
-2
0
00.511.522.53
0
50
100
150
200
250
0 150 300 450 600 750 900
Typical Characteristics
SHDN Threshold Voltage vs. Input V oltage
SHDN Threshold Voltage (V)
Input Voltage (V)
PSRR vs. Frequency
Frequency (HZ)
PSRR (dB)
IOUT =50mA
COUT=10uF
CBP=0.1uF
Output Current vs. Output Voltage
Output Current (uA)
Output Voltage (V)Output Current (mA)
Dropout Voltage (mV)
VIN=0V
VIN=0V
VIN=4V
VIN=5V
APL5901/2-33
APL5901/2-33
Dropout Voltage vs. Output Current
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw7
0
50
100
150
200
250
300
350
400
450
500
0 0.1 0.2 0.3 0.4
-100u
100u
-80u
-
-40u
-20u
0
20u
40u
60u
80u
010m
2m
4m 6m 8m
Typical Characteristics
Output Noise
Time (s)
VOUT (50uV/div)
VIN=4.3V
IOUT =0mA
C
OUT=10uF
C
BP=0.1uF
Output Noise vs. Bypass Capacitor
Output Noise (uV)
Bypass Capacitor (uF)
Load-Transient Response
Output Voltage (50mV/div)
Time (10µs/div)
VOUT
IOUT=1mA~900mA
Time (40µs/div)
VOUT
VIN
Line-Transient Response
VIN=VOUT+1V
COUT=4.7µF
Output Voltage (20mV/div)
APL5901/2-33
APL5901/2-33
APL5901/2-33APL5901/2-33
4V
3V
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw8
0.001
0.01
0.1
1
0 150 300 450 600 750 900
VOUT
COUT=1µF
No Load
Typical Characteristics
Entering Shutdown
Time (1ms/div)
VOUT
vSHDN
Shutdown Exit Delay
Time (20ms/div)
VOUT
vSHDN
CBP=100nF
No Load
Time (200ms/div)
VOUT=3.3V
Region of Stable ESR vs. Load Current
Load Current (mA)
COUT ESR (Ω)
Shutdown Exit Delay
unstable
stable
APL5901/2-33 APL5901/2-33
APL5901/2-33
APL5901/2-33
3.3V
4V
3.3V
4V
0V
0V
0V
0V
3.3V
4V
0V
0V
CBP=10nF
No Load
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw9
3.25
3.27
3.29
3.31
3.33
3.35
-40 0 40 80 120
Typical Characteristics
Output Voltage vs. Temperature
Temperature (°C )
Output Voltage (V)
APL5901/2-33
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw10
The minimum input-output voltage difference (dropout)
determines the lowest usable supply voltage. In battery-powered systems, this will determine the useful
end-of-life battery voltage. Because the APL5901/2
use a p-channel MOSFET pass transistor, the dropout voltage is a function of drain-to-source on-resistance (R
DS(ON)
) multiplied by the load current.
The APL5901/2 load-transient response graphs in typical characteristics show the transient response. A
step change in the load current from 10mA to 900mA
at 10µs will cause a 20mV transient spike. Larger
output capacitor and lower ESR can reduce transient
spike.
Application Information
Capacitor Selection and Regulator
Stability
The APL5901/2 use at least a 1µF capacitor on the
input, and this capacitor can be Aluminum, Tantalum
or Ceramic capacitor. The input capacitor with larger
value and lower ESR provides better PSRR and linetransient response. The output capacitor also can use
Aluminum, T antalum or Ceramic capacitor, and a minimum value of 4.7µF and ESR above 0.02Ω is
recommended. A larger output capacitor can reduce
noise and improve load-transient response, stability,
and PSRR. Note that some ceramic dielectrics exhibit large capacitance and ESR variation with
temperature. When using this capacitor, a minimum
10uF or more may be required to ensure the stability
at low temperature operation. Use a bypass capacitor at BP pin for low output nvise. Increasing the capacitance will slightly decrease the output noise, but
increase the start-up time.
Load-Transient Considerations
Input-Output (Dropout)Voltage
Reverse Cur r ent Protection
The APL5901/2 have an internal reverse protection, it
does not need an external schottky diode to connect
the regulator input and output. If the output voltage is
forced above the input voltage by more than 11mV,
the IC will be shutdown and the ground pin current is
below 0.1uA.
Current Limit
The APL5901/2 have a current limit protection. The
ouptut voltage will drop close to zero volt, when load
current reaches the limit, and then the load current
will be limited at 200mA after output voltage is below
0.7V. When the load current back to the value where
limiting started, the output voltage and current will return to normal value. When output is shorted to
ground, the APL5901/2 will keep short circuit current
at 200mA .
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw11
Thermal protection limits total power dissipation in the
device. When the junction temperature exceeds
T
J
=+150J, the thermal sensor generates a logic signal to turn off the pass transistor and allows IC to
cool. When the IC’s junction temperature is down by
10J, the thermal sensor will turn the pass transistor
on again, resulting in a pulsed output during continuous thermal protection. Thermal protection is designed
to protect the APL5901/2 in the event of fault
conditions. For continuous operation, do not exceed
the absolute maximum junction temperature of
T
J
=+150J.
Operating Region and Power Dissipation
The thermal resistance of the case to circuit board,
and the rate of air flow all control the APL5901/2’s
maximum power dissipation. The power dissipation
across the device is PD = I
OUT (VIN-VOUT
) and the maximum power dissipation is:
P
DMAX
= (TJ-TA) / (?JC +?CA)
where TJ-TA is the temperature difference between the
junction and ambient air, ?JC is the thermal resistance of the package, and?CA is the thermal resistance through the printed circuit board, copper traces,
and other materials to the ambient air.
The GND pin of the APL5901 provide an electrical connection to ground and channeling heat away. If power
dissipation is large, connect the GND pin to ground
using a large pad or ground plane, can improve the
problem of over heat of IC.
Thermal Protection
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw12
Packaging Information
Millimeters Inches
Dim
Min. Max. Min. Max.
A 1.35 1.75 0.053 0.069
A1 0.10 0.25 0. 004 0.010
D 4.80 5.00 0.189 0.197
E 3.80 4.00 0.150 0.157
H 5.80 6.20 0.228 0.244
L 0.40 1.27 0.016 0.050
e1 0.33 0. 51 0.013 0.020
e2 1.27BSC 0.50BSC
φ
18
°
8
°
HE
e1 e2
0.015X45
D
A
A1
0.004max.
1
L
SOP-8 pin ( Reference JEDEC Registration MS-012)
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw13
SOT-223( Reference JEDEC Registration SOT-223)
B1
D
H E
K
e
e1
A
c
L
A1
a
B
b
Millimeters InchesDim
Min. Max. Min. Max.
A 1.50 1.80 0.06 0.07
A1 0.02 0.08
B 0.60 0.80 0.02 0.03
B1 2.90 3.10 0.11 0.12
c 0.28 0.32 0.01 0.01
D 6.30 6.70 0.25 0.26
E 3.30 3.70 0.13 0.15
e 2.3 BSC 0.09 BSC
e1 4.6 BSC 0.18 BSC
H 6.70 7.30 0.26 0.29
L 0.91 1.10 0.04 0.04
K 1.50 2.00 0.06 0.08
α
0
°
10
°
0
°
10
°
β
13
°
13
°
Packaging Information
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw14
Packaging Information
D
D1
e
B1
e1
B
123
L
H
E
C
a
a
A
SOT-89 (Reference EIAJ ED-7500A Reg stration SC-62)
Millimeters Inches
Dim
Min. Max. Min. Max.
A 1.40 1.60 0.055 0.063
B 0.40 0.56 0.016 0.022
B1 0.35 0.48 0.014 0.019
C 0.35 0.44 0.014 0.017
D 4.40 4.60 0.173 0.181
D1 1.35 1.83 0.053 0.072
e 1.50 BS C 0.059 BSC
e1 3.00 BSC 0.118 BSC
E 2.29 2.60 0.090 0.102
H 3.75 4.25 0.148 0.167
L 0.80 1.20 0.031 0.047
α
10
°
10
°
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw15
Packaging Information
SOT-89-5
M illimete rs Inc h e s
Dim
Min. Max. Min. Max.
A 4 .4 0 4.60 0.17 0.1 8
B 4 .0 5 4 .2 5 0.1 6 0 .1 7
C 1 .5 0 1.7 0 0.0 6 0 .0 7
D 1 .3 0 1.5 0 0.0 5 0 .0 6
E 2 .4 0 2 .6 0 0.0 9 0.1
F 0.80 - 0.03 G 3 .0 0 R E F 0 .1 2 R E F
H 1 .5 0 RE F 0.0 6 RE F
I 0.40 0.5 2 0 .0 1 0.0 2
J 1.4 0 1.6 0 0 .0 5 0.0 6
K 0 .3 5 0 .4 1 0.0 1 0 .0 2
L 5 TYP 0.2 TYP
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw16
Packaging Information
TO-252-5
Millimeters Inches
Dim
Min. Max. Min. Max.
A 6.40 6.8 0 0.25 0.2 6
B 5.20 5.5 0 0.20 0.2 1
C 6 .8 0 7.20 0.26 0.2 7
D 2 .2 0 2.80 0.08 0.11
P 1.27 REF 0.05 REF
S 0.50 0.8 0 0.02 0.0 3
H 2 .2 0 2.40 0.08 0.0 9
J 0.45 0 .5 5 0.01 0.0 2
K 0 0.15 0 0.006
L 0 .9 0 1.50 0.0 3 0.06
M 5.40 5.8 0 0.21 0.2 2
L
K
J
H
B
A
C
M
D
PS
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw17
Packaging Information
TO-252( Reference JEDEC Registration TO-252)
Millimeters Inc hes
Dim
Min. Max. Min. Max.
A 2.18 2.39 0.086 0.094
A1 0.89 1.27 0.035 0.050
b 0.508 0. 89 0.020 0. 035
b2 5.2 07 5.461 0.205 0.215
C 0.46 0.58 0.018 0.023
C1 0.46 0.58 0.018 0.023
D 5.334 6.22 0. 210 0.245
D1 5.2 REF 0.205 REF
E 6.35 6.73 0.250 0.265
E1 5.3 REF 0.209 REF
e1 3.96 5.18 0.156 0.204
H 9.398 10.41 0.370 0.410
L 0.51 0.020
L1 0.64 1.02 0.025 0.040
L2 0.89 2. 032 0.035 0.080
L2
D
L1
b
b2
E
C1
A
H
L
C
A1
e1
D1
E1
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw18
Physical Specifications
Pre-heat temperature
183 C
Peak temperature
Time
°
temperature
Classification Reflow Profiles
Convection or IR/
Convection
VPR
Average ramp-up rate(183°C to Peak) 3°C/second max. 10 °C /second max.
Preheat temperature 125 ± 25°C)
120 seconds max
Tem perature maintained above 1 83°C
60 – 150 seconds
Time within 5°C of actual peak temperature
10 –20 seconds 60 seconds
Peak temperature range
220 +5/-0°C or 235 +5/-0°C 215-219°C or 235 +5/-0°C
Ramp-down rate
6 °C /second max. 10 °C /second max.
Time 25°C to peak temperature
6 minutes max.
Package Reflow Conditions
pkg. thickness
≥≥≥≥
2.5mm
and all bgas
pkg. thickness < 2.5mm and
pkg. volume
≥≥≥≥
350 mm³
pkg. thickness < 2.5mm and pkg.
volume < 350mm³
Convection 220 +5/-0 °C Convection 235 +5/- 0 °C
VPR 215-219 °C VPR 235 +5/-0 °C
IR/Convection 220 +5/-0 °C IR/Convection 235 +5/-0 °C
Terminal Material Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb)
Lead Solderability Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3.
Reference JEDEC Standard J-STD-020A APRIL 1999
Reflow Condition (IR/Convection or VPR Reflow)
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw19
R e lia bility te s t pro g r a m
Test item Method Description
SOLDERABILITY MIL-STD-883D-2003
245°C , 5 SEC
HO LT MIL-STD-883D-1005.7
1000 Hrs Bias @ 125 °C
PCT JESD-22-B, A102
168 Hrs, 100 % RH , 121°C
TST MIL-STD-883D-1011.9
-65°C ~ 150°C, 200 Cycles
ESD MIL-STD-883D-3015.7 VHBM > 2KV, VMM > 200V
La tc h -Up J E SD 78 1 0 ms , Itr > 100mA
Carrier Tape
A
J
B
T2
T1
C
t
Ao
E
W
Po
P
Ko
Bo
D1
D
F
P1
Copyright ANPEC Electronics Corp.
Rev. B.1 - Jun., 2003
APL5901/2
www.anpec.com.tw20
Cover Tape Dimensions
Anpec Electronics Corp.
Head Office :
5F, No. 2 Li-Hsin Road, SBIP,
Hsin-Chu, T aiwan, R.O.C.
T el : 886-3-5642000
Fax : 886-3-5642050
Taipei Branch :
7F, No. 137, Lane 235, Pac Chiao Rd.,
Hsin Tien City, Taipei Hsien, Taiwan, R. O. C.
T el : 886-2-89191368
Fax : 886-2-89191369
Customer Service
Reel Dimensions
Applica tio n
A B C J T1 T2 W P E
330 ± 1 62 +1.5 12.75+ 0.15 2 ± 0.5 12.4 ± 0.2 2 ± 0.2 12± 0. 3 8± 0.1 1.75±0.1
F D
D1 Po P1 Ao Bo Ko t
SOP- 8
5.5± 1 1.55 +0.1 1.55+ 0.25 4.0 ± 0.1 2.0 ± 0.1 6.4 ± 0.1 5.2± 0. 1 2 .1± 0.1 0 .3±0.013
Applica tio n
A B C J T1 T2 W P E
178 ±1 70 ± 2 13.5 ± 0.15 3 ± 0.15 14 ± 2 1.3 ± 0.3
12 + 0.3
12 - 0.1
8 ± 0.1 1 .7 5± 0.1
F D D1 Po P1 Ao Bo Ko t
SOT-89
5.5 ± 0.05 1.5± 0.1 1 .5± 0.1 4 .0 ± 0.1 2.0 ± 0.1 4 .8 ± 0.1 4.5± 0.1 1.8 0± 0.1 0.3±0.013
Applica tio n
A B C J T1 T2 W P E
330±162±1.5
12.75
±
0.15
2 ± 0.6 12.4 +0.2 2± 0.2 12 ± 0.3 8 ± 0.1 1 .7 5± 0.1
F D D1 Po P1 Ao Bo Ko t
SOT-223
5.5 ± 0.05 1.5+ 0.1 1.5+ 0.1 4.0 ± 0.1 2.0 ± 0.05 6.9 ± 0.1 7.5± 0.1 2 .1± 0.1 0.3±0.05
Applica tio n
A B C J T1 T2 W P E
330 ±3 100 ± 2 13 ± 0. 5 2 ± 0.5
16.4 + 0.3
-0.2
2.5± 0.5
16+ 0.3
- 0.1
8 ± 0.1 1 .7 5± 0.1
F D D1 Po P1 Ao Bo Ko t
TO-252
7.5 ± 0.1 1.5 + 0 .1 1 .5± 0.25 4.0 ± 0.1 2.0 ± 0.1 6 .8 ± 0.1 10.4± 0.1 2 .5± 0.1 0.3±0.05
Application Carrier Width Cover Tape Width Devices Per Reel
SOP- 8 12 9.3 2500
SOT- 89 12 9.3 1000
SOT- 223 12 9.3 2500
TO- 252 16 13.3 2500
Loading...