Anova TAN3284P-4', TAN3284T-4', TAN3284MR-4', TAN3284FM-4', TAN3280FM-6' Assembly Instructions Manual
...
!
Assembly Instructions
Tandem Contour Benches
TAN3280P-6'
TAN3280T-6'
TAN3280FM-6'
TAN3280MR-6'
anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED:
• 5/32" Allen wrench
• 1/4" Allen wrench
• 3/16" Wire pull rod
• 5/16" Open-end or
box-end wrench
BENCH COMPONENTS: Pattern may vary on the bench seat and backrest panels.
Perspective Mountain RangeTotem Fractured Movement
4' Benches will be available soon.
TAN3284P-4'
&
TAN3284T-4'
&
TAN3284FM-4'
&
TAN3284MR-4'
&
--PERSPECTIVE
TOTEM
--FRACTURED MOVEMENT
MOUNTAIN RANGE
(1) Rear Backrest Panel
(1) Front Backrest Panel
ASSEMBLY HARDWARE: All hardware is stainless steel.
(8) 5/16"-18 x 1"
Allen Head Screws
ASSEMBLY:
CAUTION: Steps 3 – 10 are applicable for the assembly of optional 2-light and 3-light LED kits. For a 3-light LED
kit, include steps A – G on page 4.
NOTE: LED light kit components must be assembled and mounted to the bench before the panel assemblies.
This is a two-person assembly.
(7) 1/4"-20 x 5/8"
Allen Head Screws
(2 or 3) Optional
LED Light Fixtures
(1) Bench Seat
(4) 6-32 x 3/8"
Hex Head Bolts
(1) Optional Bench Seat
Aluminum Wire Cover
(2) Optional
Mounting Flanges
(4) 6-32 x 5/16"
Nylock Nuts
(1) Optional Back
Panel Wire Cover
(4) 5/16" Flat
Washers
(3) 1/4" Flat
Washers
(1) Le End
Casting
Additional Hardware Not
Included with Purchase
(2) Heat Shrink Crimp
(1) Right End
Casting
Inspect the shipping container contents for damage and to determine that all components and hardware are present.1.
2. Lay all parts on a so work surface or on the shipping packaging to prevent
damage to the nish.
NOTE: Before assembling the nuts to the bolts, it is recommended that a
light oil or petroleum jelly be applied to the screw threads.
3. Locate one of the mounting anges and one of LED light xtures. Mount
the light xture to the ange by inserting two 6-32 x 3/8" hex head bolts
through the mounting holes. Place two 6-32 x 5/16 Nylock nuts on the ends
of the screws and tighten them with the 5/16" open-end or box-end wrench.
Repeat this process to install the remaining LED light xture to the other
ange.
6-32 x 5/16"
Nylock Nut
Mounting Flange
LED Light
6-32 x 3/8"
Hex Head Bolt
1
4. Locate the bench seat and wire cover.
Insert the bench seat aluminum wire cover through the
square slots on the bench seat.
Pull the wires leads of the LED light xture through the
5.
middle hole of the bench seat. Make sure all of the slack is
pulled through.
Bench Seat
Square Slots
Bench Seat Aluminum Wire Cover
Mount the mounting ange to the bench seat by inserting
two 1/4"-20 x 5/8" Allen head screws through the mounting
holes of the ange and tightening them to the pre-installed
rivet nuts on the bench seat with the 5/32" Allen wrench.
Repeat this process on the opposite side.
NOTE: The wire leads run through a small channel with a
6.
stainless steel tube in the le end casting so make sure
the wire leads run from the right side to the le side.
Pull the wire leads from the right end of the bench seat
through the aluminum wire cover using the 3/16" wire pull
rod.
Wire Leads
Mounting Flange
1/4"-20 x 5/8" Allen Head Screw
Le end of the bench
Right end of the bench
Take the wires from the light xture that is mounted to the le
7.
end of the bench and measure approximately 2 feet of wire from
the xture, then cut and save the excess wire. It will be needed
in step 9.
Connected wire leads
2
NOTE: The le end casting has two threaded holes about half
!
REVISIONS
REV.
DESCRIPTION
DATE
3
2
1
8.
way up the back leg and also has a channel in the bottom of
the back leg for the wire to run through. The right leg only has
one threaded hole and does not have a channel.
Locate the end castings and place them next to the bench seat.
NOTE: Refer to steps A – G on page 4 if the 3-light
LED kit is being installed. Return to steps 13- 17 to
complete the assembly of the bench.
Seat access hole
Locate the trimmed spare wires from step 7 and guide them through the
9.
hole in the back of the leg of the le end casting by pulling them through
with the 3/16" wire pull rod until there is approximately 2 feet of wire
remaining out of the seat access hole.
Strip each wire end of insulation until approximately a 1/4" of bare wire
is exposed. Using the heat shrink crimps, secure one wire from each of
the LEDs in to one end of the crimp and insert one of the wires that runs
through the casting into the other. Then use a heat gun to seal the heat
shrink crimp. Repeat the process for the remaining loose wires.
10.
Caution: To avoid pinching or damaging the LED wire, use the
compartment built into each of the bench castings to tuck any excess
wire.
Mount the bench seat to the end casting by inserting two 5/16"-18 x 1"
Allen head screws and through the mounting holes.
Two holes
One hole
Le End Casting Right End Casting
Le LED wires
Repeat this process on the on the opposite side.
Tighten all of the hardware nger tight.
Bench Seat
Le End Casting
5/16"-18 x 1"
Allen Head Screw
11. Turn the bench over into an upright position.
12. Insert two of the 5/16"-18 x 1" Allen head screws through the
mounting holes of the front backrest panel and the right end
casting and tighten them nger tight.
Compartment for
the excess wires.
Allen Head Screw
5/16"-18 x 1"
Right LED wires
Wires through
casting
Front Backrest
Panel
Repeat this process on the opposite side.
Then tighten the screws with the 1/4" Allen wrench.
3
13. Locate the rear backrest panel and slide its mounting brackets over
top of the front backrest panel's mounting brackets.
14. Insert the three 1/4"-20 x 5/8" Allen head screws and three 1/4" at
washers into the rear backrest panel's mounting holes. Then tighten the
screws with the 5/32" Allen wrench.
15. Tighten the remaining 5/16" screws on the bottom side of the bench with
the 1/4" Allen wrench.
16. Aer the bench with LED xtures is fully assembled, approximately 4 feet
of lead wire will be available to route to the power supply.
17. Aer two weeks, retighten all of the hardware.
3-LED Light Assembly
Front Backrest Panel
Mounting Bracket
Rear Backrest Panel
Mounting Bracket
1/4"-20 X 5/8"
Allen Head Screw
1/4" Flat Washer
Locate the 3rd LED xture and guide the wires through the wire
A.
channel hole and out of the seat access hole. Be sure to leave
approximately 40" of wire between the light xture and casting
so that this LED xture can reach the middle of the front backrest
panel in the following steps.
B. Locate the trimmed spare wires from step 7 and guide them
through the hole in the back of the leg of the le end casting by
pulling them through with the 3/16" wire pull rod until there is
approximately 2 feet of wire remaining out of the seat access
hole.
Strip each wire end of insulation until approximately a 1/4" of
bare wire is exposed.
(i) Using the heat shrink crimps, secure one wire from each of the
LED xtures from the bench seat into one end of the crimp.
(ii) Next, insert one wire from the front backrest panel LED xture
and one of the wires that run through the casting into the other
end of the heat sink crimp. Then use a heat gun to seal the heat
shrink crimp. Repeat the process for the remaining loose wires.
Wire Channel
Hole
Seat access hole
Le LED wires
Le End Casting
Back LED wires
(i)
(ii)
Right LED wires
Wires through
casting
4
!
C.
REVISIONS
REV.
DESCRIPTION
DATE
3
2
1
Caution: To avoid pinching or damaging the LED wire, use the compartment built into each of the bench castings to
tuck any excess wire.
Mount the bench seat to the end casting by inserting two 5/16"-18 x 1" Allen head screws and through the mounting holes.
Repeat this process on the on the opposite side.
Tighten all of the hardware nger tight.
Compartment for
the excess wires.
Bench Seat
Le End Casting
Insert two of the 5/16"-18 x 1" Allen head screws through the mounting
D.
holes of the front backrest panel and the right end casting and tighten
them nger tight.
Insert one of the 5/16"-18 x 1" Allen head screws through the top
mounting holes of the front backrest panel and the le end casting and
tighten it nger tight.
Mount the LED light xture to the back panel mounting bracket by
E.
inserting two 6-32 x 3/8" hex head bolts through the mounting holes.
Place two 6-32 x 5/16" nylock nuts on the ends of the screws and tighten
them with the 5/16" open-end or box-end wrench.
6-32 x 3/8" Hex Head Bolt
5/16"-18 x 1"
Allen Head Screw
Front Backrest
Panel
LED Light Fixture
6-32 x 5/16" Nylock Nut
5
F. Locate the back panel wire cover and insert its from a high angle into the
LED mounting bracket's slot. Once it is in the slot lower it down onto the
back rest panel.
G. Mount one of the 5/16"-18 x 1" Allen head screws to the le end casting
aligning the screw with the curve on the back panel wire cover.
Then tighten all of the screws on the rear back panel with the 1/4" Allen
wrench.
LED Mounting
Bracket Slot
5/16"-18 x 1"
Allen head screw
6
21.75"
47.44"
O 0.50"
O 0.50"
Tandem 4' Contour Bench Foot Mount
21.75"
70.62"
Tandem 6' Contour Bench Foot Mount
Tandem Assembly and Replacement Parts
Rear Backrest Panel
Front Backrest Panel
Right End Casting
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
1/25/2018 Copyright 2018 ANOVA® Made in USA.
LED Light Fixture
Le End Casting
Bench Seat
Mounting Flange
Wire Cover
7
Loading...