ANNTLENT CPA70 User Manual

AN-CPA70 Plus
Cell Phone Signal Booster
User Manual
1/12
Introduction
With the popularity of mobile communications, people want to make a call anytime, anywhere, so
the coverage requirement of communication network is higher and higher, but the reality is not so,
sometimes mobile phone signal is not very good, you want to make a smooth call, even in some places
cell phone cannot dial out. in this cases, cell phone signal booster can solve this problem in a certain
extent.
Features
AGC(Automatic Gain Control):
uplink and downlink can automatically reduce the gain and reduce the interference signal
Self- Oscillation elimination:
detects the loop, and finds that the self- oscillation is eliminated, the system returns to normal working
state, otherwise, the power is turned off to prevent interference signal.
When the downlink output signal is too strong or self- oscillated, the
The system detects self- Oscillation, first reduces the link gain, then
Inactivity Mode:
switched off, and the static power is decreased by 30%, so as to achieve the purpose of energy saving.
When no user calls, the device is in standby mode, the uplink power amplifier is
SAFETY WARNINGS
WARNING: This equipment should be installed and operated with minimum distance 20cm 8 inchesbetween the radiator& your body.
FCC Cautions:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-- Consult the dealer or an experienced radio/TV technician for help
2/12
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating instruction
for satisfying RF exposure compliance.
This transmitter must not be co-located or operating in conjunction with any other
Antenna or transmitter.
SAFTY W ARN ING:
End users must follow the specific operating instruction for satisfying RF exposure
compliance.
Do not remove the covers during working.
Do not try to repair or replace any components inside of the equipment. Alteration
or abuse of the equipment or other components will void this product’s warranty,
and could be dangerous to the user.
PACKAGE CONTENTS
(1) Packages include the follo wing
1 2
1Pcs AN-CPA70 Plus Booster with N Female connectors.
AC/DC Power Adaptor. Screws Mounting Kits.User manual (this document).
Booster interface description:
(2)
3/12
Manual gain control knob and LED light:You can manually rotate the knob to adjust the gain of
the corresponding frequency band .The corresponding LED on the right is used to indicate the following
different working conditions of the booster.
LED Indicator
Booster working conditions
LED LIGHT
Continuous GREEN @normal
Twinkly GREEN @input signals may be not enough
Continuous YELLOW @ stronger input signals, AGC is working
Twinkly YELLOW@ self–oscillation happen ,AGC is working.
Continuous RED@ power supply is shut down
Twinkly RED@ self–oscillation happen but power supply is NOT shut down.
Power supply jack: The booster uses a power input range of DC 5-12V. INDOOR and OUTDOOR portThe two ports are used to connect outdoor and indoor
antennas.
(3)Antennas and Cables:
In order to use the Booster, you still need the corresponding indoor antenna 1pcs,
outdoor antenna 1pcs, outdoor cable 1pcs and indoor cable 1pcs.
Antennas and cables kitting information are as follows
Name Model Gain/Loss
Indoor Antenna
Outdoor Antenna
Rubber Antenna PTE-RB-800-2100
Ceiling Antenna PTE-CI-800-2500 3dbi @698-787MHz
Indoor Panel Antenna PTE-PN-800-2500 7dbi @698-787MHz
YAgi Antenna
PTE-YG-800/1900
3dbi @698-787MHz
3dbi @824-894MHz
3.5dbi @1850-1990MHz
3.5dbi @1710-2155MHz
3dbi @824-894MHz
4.5dbi @1850-1990MHz
4.5dbi @1710-2155MHz
7dbi @824-894MHz
8.5dbi @1850-1990MHz
8.5dbi @1710-2155MHz
8dbi @698-787MHz
8dbi @824-894MHz
10dbi @1710-1755MHz
10dbi @1850-1990MHz
10dbi @2110-2155MHz
4/12
Loading...
+ 8 hidden pages