Anhui Inno Sign 92194 user manual

Camping COB Lantern

With Power Bank And

Wireless Charger

Instruction Manual

92194

Features:

1.

Wireless Charging Pad

2.

SOS Flash Light

3.

Lantern

4.

Light Button

5.

Wireless Charging button

6.

USB output

7.

LED Indicator

8.

Micro-USB input

9.

Wireless Charging Indicator

What’s included:

1 x Power Bank Lantern
1 x 2-in-1 charging cable (see above diagram)
1 x Instruction Manual

Capacity: 10000 mAh/3.7V/37Wh

•
Micro-USB Input: DC 5V/2A

•
USB Output: DC 5V/2A

•
Wireless Output: 5V/1A

•

Instructions:

Charging the power bank:

1

.

a.

Charge the power bank fully before usage.

b.

Using 2-in-1 charging cable, insert the USB

USB port of a computer, insert the 2-in-1
tip (the side with pins upwards) into power
bank micro input. Then charge begins.

c.

Once all 4 LED are illuminating and stop

Lantern & Emergency Light:

2

.

a.

Press the Light Button(4) to turn on the
lantern.
If you continue to press the Light Button

b.

there are 4 light modes (100% Brightness,

light, Light OFF).

.

3

Wireless Charging:

a.

Press the Wireless Charging Button(5)
the Wireless Charging Indicator(9) will
illuminate BLUE.
Place wireless charging enabled device

b.

onto the Wireless Charging Pad(1),
indicator will turn RED when charging a
device.

c.

Press the Wireless Charging Button again

.

4

Charging with USB Port:

a.

Connect the 2-in-1 cable to your mobile
phone/device. If Android device, the tip with
pins upwards; If iOS device, the tip without
pins upwards. Connect the other end of the
power bank output. Then charge begins.

b.

While the device is charging , the power
bank LED indicator will show the current
energy of the battery.

SAFETY PRECAUTIONS:

WARNING–When using this product, basic
precautions should always be followed,
including the following:

1.

Read all the instructions before using the
product.

2.

Charge the power bank fully before initial use.
The unitʼs full performance is achieved only
after 2 or 3 completed charge and discharge
cycles.

3.

To reduce the risk of injury, close
supervision is necessary when the product
is used near children.

4.

Do not expose the device to moisture.

5.

Do not use the device in excess of its
output rating. Overload outputs above

6.

Do not use the device if damaged or

7.

explosion or risk of injury.

8.

Do not disassemble the device. Take it to

or repair is required. Incorrect reassembly

9.

or temperatures above 212ºF may cause
explosion.

10.
repair person using only identical
replacement parts.

11.

This will ensure that the safety of the
product is maintained.
Do not overcharge Phone. Unit may get hot

12.
with excessive use. Remove Phone when it
is fully charged. Never charge for more than
7 hours at a time.

FCC Statement:

This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
This device may not cause harmful

(1)

interference, and
This device must accept any interference

(2)

received, including interference that may
cause undesired operation.

Warning:

*

approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.

FCC ID: 2ANFN-92194

WIRELESS CHARGING ENABLED
DEVICES:

iPhone 8/8Plus/X, Samsung Galaxy S8/
S8+/S7/S7 Edge/S6/S6 Edge, Nokia Lumia
1020/920/928, HTC 8X, HTC Droid DNA, HTC
Rzound, HTC Incredibly 4G LTE, Moto Droid
Turbo, Motorola Moto 360 Smart Watch, Moto
Droid Maxx, Droid Mini, Google Nexus 6/4/5/7
(2013), LG D1L, LG LTE2, LG G2 (Verizon),
Blackberry Z30 (Verizon)

NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications.

However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment
and receiver.

-Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.

-Consult the dealer or an experienced radio/TV
technician for help

Changes or modifications not expressly approved
by the party responsible for compliance could void
the user's authority to operate the equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference,
and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.

RF Exposure Warning Statements:This equipment
complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This
equipment shall be installed.and operated with
minimum distance 20cml between the radiator &
body.

MADE IN CHINA