Page 1
shadow focus floodlight
SFS-300
INSTRUCTIONS
Page 2
Introduction
Congratulations on your purchase of the Angler SFS-300.
The pro-style SFS-300 provides 300 watts of smooth light with focusing
ability and is an ideal fixture for quick and easy set-ups on location or in the
studio. It features a convenient cool-touch handle and a 12.5-ft. AC cable
with an in-line, heavy-duty, rocker power switch. This light incorporates
several advanced features such as a double-slot filter/scrim holder and a
four-leaf barndoor. The system will accommodate a 300-watt, 120-volt bulb
and the durable polycarbonate construction was designed to provide many
years of trouble-free service. Please read these operating instructions and
safety precautions carefully before operating this equipment.
Highlights
Four-stop range - full power to 1/16 power in .10 f/stop increments
Low cost and compact 300-watt flood light
21-40° focusable beam pattern
Ideal for quick and easy set-ups, on location or in the studio
Four-leaf barndoor
Accepts 5-5/8˝ scrims and accessories
2
Page 3
Contents
Four-way barndoor set
Impact JCD Lamp
300W, 120V
Also included: User manual
Safety Glass
One-year limited warranty
3
Page 4
Operating Instructions
Barndoor attachment
Loosen the barndoor locking screw (A) and
open the hinged barndoor locking bracket
(B). Seat the barndoor mounting collar in
the three fixed barndoor brackets (C), then
close the locking bracket and retighten the
locking screw. When properly installed, the
barndoors are free to rotate 360°.
C
A
B
Mount on light stand
The SFS-300 mounts on any standard,
5/8˝ diameter light stand. Loosen the
light stand lock knob (1), and seat the
mounting spigot onto the top of the light
stand. Tighten the lock knob firmly. Do not
overtighten.
4
1
Page 5
Adjust light angle
Loosen the angle tilt knob (2), and position
light angle as desired. Retighten tilt knob.
Do not overtighten.
Connect to power supply
Plug power cord into a grounded 110/120V
AC power supply only.
Switch on power
Rock the power switch (3) to the “on”
_
position (
).
2
3
5
Page 6
Note
It is normal for the SFS-300 to smoke for a few minutes when first used, as the intense
heat from the lamp initially burns o manufacturing residues. Smoking for longer than
15 minutes, however, is not normal, and may indicate a malfunction. If so, discontinue
use and return to place of purchase. Quartz bulb filaments are fragile and easily broken,
especially when hot. Always handle the SFS-300 carefully to avoid shock to the bulb
filaments.
Adjust beam focus
Rotate lamp adjustment knob (4) clockwise
for a spotlight eect, or counterclockwise
for a floodlight eect.
6
4
Page 7
Changing the lamp
1. Disconnect unit from power supply.
2. Allow light to cool to room temperature before handling.
3. Remove safety glass by unscrewing the three retaining screws.
4. Remove expired lamp by pulling it straight out of the socket.
5. Insert new lamp in its plastic sleeve by pushing pins straight into the socket (a very
tight fit is normal and necessary for proper operation). Then remove plastic sleeve.
6. Replace safety glass.
Caution: Never handle quartz bulbs with bare fingers, as skin oils can cause the bulbs to
shatter unexpectedly. Always use cotton gloves or a clean fabric swatch.
Replacement Quartz Halogen Lamps: 300W 2-pin JCD 120V
7
Page 8
SPECIFICATIONS
Construction
Reflector 4˝ anodized aluminum
Light beam spread 21-40°
Socket 2-pin (GY9.5)
Switch Inline power cord
Power cord 120V AC
Mount 5/8 inch
WEIGHT 3.46 lbs. (1.5 kg)
Dimensions
including mount (H × W × Ø)
Wat ts 300
Color Temperature 3100° K
Average Life 100 hours
Approx. Lumens 7,500
Synthetic housing,
convection vented
cooling
ʺ
× 8.75ʺ × 6
8.75
(22 × 22 × 15 cm)
ʺ
8
Page 9
Warnings
Quartz lamps generate extreme heat. To avoid injury, do not touch the light
housing while lamp is lit.
Allow light to cool to room temperature before storing or handling.
To prevent bulb failure, do not bump or jar unit while lamp is hot.
Do not operate unit without the safety glass installed.
To avoid overheating, do not block vents or operate unit in a downward position
for extended periods of time.
This unit can cause severe burns if mishandled. Keep out of reach of children.
This unit is equipped with a 6.3A safety fuse (5). Replace with a fuse of similar
rating only.
5
9
Page 10
Power Requirements
This light is designed for use with 110/120V AC power only, and is supplied
with a three prong, grounded plug. Do not attempt to defeat this safety
feature. If necessary, use only grounded extension cords rated for 6 amps
Safety Glass
The SFS-300 is supplied with a heat-resistant safety glass to prevent
personal injury or property damage should the lamp shatter. Never operate
the light without the safety glass in place.
10
Page 11
One-Year Limited Warranty
ANGLER
A Gradus Group
Brand
TM
This Angler product is warranted to the original purchaser to be free from defects in materials and
workmanship under normal consumer use for a period of one (1) year from the original purchase date
or thirty (30) days after replacement, whichever occurs later. The warranty provider’s responsibility
with respect to this limited warranty shall be limited solely to repair or replacement, at the provider’s
discretion, of any product that fails during normal use of this product in its intended manner and in
its intended environment. Inoperability of the product or part(s) shall be determined by the warranty
provider. If the product has been discontinued, the warranty provider reserves the right to replace it
with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY
PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you
with specific legal rights, and you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Angler Customer Service Department to obtain a return
merchandise authorization (“RMA”) number, and return the defective product to Angler along with
the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own
risk and expense.
For more information or to arrange service, visit www.anglerlights.com or call Customer Service at
212-594-2353.
Product warranty provided by the Gradus Group.
www.gradusgroup.com
Angler is a registered trademark of the Gradus Group.
© 2015 Gradus Group LLC. All Rights Reserved.
GG1
11
Page 12
anglerlights.com
Loading...