Page 1
steady cool fluorescent
IUF-55
INSTRUCTIONS
Page 2
Introduction
Congratulations on your purchase of the Angler IUF-55.
The Angler Steady Cool Fluorescent is a flicker-free fixture. It’s a lightweight
and inexpensive way to produce a soft, diuse, and glowing light in the studio
or on location.
Fluorescent bulbs are cool to the touch, so they’re ideal for photographing
subjects that are very close to the light source and aected by heat, like food
or people. The IUF-55 features an air-induction cooling system that keeps
everything at a comfortable temperature.
The Steady Cool has a flexible gooseneck stand adapter that makes it possible
to mount the fixture to most light stands and easily position the light. The
built-in barn doors provide control over your lighting. Though a built-in fuse
is easily accessed the ecient electrical draw of the IUF-55 minimizes the
chance of a blown fuse or overheated circuitry.
The Steady Cool includes daylight-balanced bulbs that produce light with
a color temperature similar to daylight. Light output is maximized by the
hammered silver, reflective surface on the barn doors.
2
Page 3
Highlights
Cool-running daylight balanced fluorescent lights
Flicker-free lighting
Lightweight fixture
Built-in barn doors with hammered silver reflective
surface
Air-induction cooling
Built-in fuse circuit protection
Padded carrying case
3
Page 4
Contents
Flexible light stand adapter
Two 55W 4-pin twin-tube daylight
fluorescent bulbs
Also included: AC power cord
4
5 × 20 mm spare fuse
Soft padded carrying case
User manual
Built-in barn doors with hammered
silver reflective surface
Page 5
User Instructions
Mounting bulbs in the fixture
1. Disconnect the fixture from power source.
2. Remove the plastic retaining clip. (1)
3. Position the bulb with printed side of base
end facing up.
4. Make sure the pins on bulb align with
holes in base. (2)
5. Carefully slide the bulb into the base until
the clip locks the bulb into place.
6. Be sure the bulb is securely locked into
base. (3)
7. Replace the plastic retaining clip. (4)
8. Repeat steps 2 - 7 for each bulb.
9. Before you turn on the fixture for the
first time, be sure that the fuse holder on
the back of the unit is turned clockwise
until tight. If it’s loose, the lights will not
illuminate.
1
2
3
4
5
Page 6
Removing bulbs from the fixture
1. Disconnect the fixture from power source.
2. Remove the plastic retaining clip. (5)
3. Push the metal clip on the base to release
the bulb. (6)
6
4. Carefully pull the bulb out of base
5. Replace the plastic retaining clip.
SPECIFICATIONS
INPUT VOLTAGE 110 ~ 220 V 50/60 Hz
Amperage 1.1 amps
Bulb switching On/Off only
Bulb type
Dimensions
Weight (including bulbs) 3.75 lb. (1.7 kg)
Standard 4-pin
twin-tube daylight
fluorescent
22.25″ × 7″ × 3.25″
(56.5 × 17.8 × 8.2 cm)
5
6
Page 7
Warnings
Handle fluorescent bulbs with care. See Note below.
Dispose of fluorescent bulbs properly.
Please read and follow these instructions, and keep this manual in a
safe place.
Keep this unit away from water and all flammable gases or liquids.
Make sure the unit is powered o when plugging it into a power
source.
Use only the correct, recommended voltage.
Do not attempt to disassemble or repair the equipment—doing so will void the
warranty, and Impact will not be responsible for any damage.
Handle the unit with care.
Do not stare at the lights when they are powered on.
Clean the unit with a soft, dry cloth.
Keep this unit away from children.
Use only parts provided by the manufacturer.
Make sure the item is intact and that there are no missing parts.
All photos are for illustrative purposes only.
7
Page 8
Limited One Year Warranty
ANGLER
A Gradus Group
Brand
TM
This Angler product is warranted to the original purchaser to be free from defects in materials and
workmanship under normal consumer use for a period of one (1) year from the original purchase date
or thirty (30) days after replacement, whichever occurs later. The warranty provider’s responsibility
with respect to this limited warranty shall be limited solely to repair or replacement, at the provider’s
discretion, of any product that fails during normal use of this product in its intended manner and in
its intended environment. Inoperability of the product or part(s) shall be determined by the warranty
provider. If the product has been discontinued, the warranty provider reserves the right to replace it
with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY
PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you
with specific legal rights, and you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Angler Customer Service Department to obtain a return
merchandise authorization (“RMA”) number, and return the defective product to Angler along with
the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own
risk and expense.
For more information or to arrange service, visit www.anglerlights.com or call Customer Service at
212-594-2353.
Product warranty provided by the Gradus Group.
www.gradusgroup.com
Angler is a registered trademark of the Gradus Group.
© 2015 Gradus Group LLC. All Rights Reserved.
GG1
Loading...