Angler ANG-633, ANG-493 User manual
glamour flash 160/300
AUG-493
AUG-633
INSTRUCTIONS
Introduction
Congratulations on your purchase of your Angler ANG Series Monolight.
The ANG Series Monolight is proof that highly functional moonlights can
be aordable. The ANG Series Monolight provides enough stored power to
light a portrait or small still-life setup. We expect that you will get many years
of trouble-free service and enjoyment from your Angler ANG Monolight.
Please read these operating instructions and safety precautions carefully
before operating this equipment.
Highlights
Four-stop range - full power to 1/16 power in .10 f/stop increments
Large LCD screen
Built-in optical slave
“Auto-Dump” feature automatically fires the flash when you step
down power
Modeling lamp can be set proportionally or independently of flash power
Cushioned “touch pad” function control buttons
Tactile feel that resists slipping and shock damage
Accepts S-mount style reflectors and head accessories (7-inch grid
reflector included)
User-replaceable flashtube
Commonly available 1/8″ mini-plug sync input
2
Contents
110-120V monolight with protective
cap and flashtube installed
Modeling lamp
ANG-493: 60W
ANG-633: 100W
Also included:
Photocell
Umbrella Holder
7″ grid reflector
Sync cable
Power cable
User manual
3
Operating the Monolight
Digital Power Readout
4
Flash Power
Control – Up
Modeling Light
Control – Up
Modeling Lamp
LED – Full
Modeling Lamp
Control
Modeling
Lamp LED –
Proportional
Recycle Tone
Control
Recycle Tone
LED
On/O Switch
FULL
PROP
AUDIO
120V/60Hz
Fuse Holder
OFF
ON
3
2
1
SYNC
SL AVE
TEST
Flash Power Control
– Down
Modeling Light
Control – Down
Photo Slave
LEDs
Photo Slave
Control
Test Fire
Button
Full Recycle
Status LED
Mini-plug
Sync Jack
Power Socket
Power Supply
Plug the power cord into the back of the flash unit. Before plugging the power cord
into the wall socket, make certain that the power switch is set to the OFF (O)
position. The Glamour Flash is designed to automatically flash, if necessary, when
turned o. The resistive dump will continue to reduce any remaining energy while the
unit is o. This is a safety feature and cannot be disabled.
Note: The Glamour Flash unit is designed to work on 110-120V 50/60Hz AC current.
Power Switch
Turn the power switch to the ON (I) position. The flash will sound a beep and the
LCD will show the current flash power setting. We recommend charging the flash unit
for one hour prior to its initial use and after an extended period of inactivity (more
than two weeks). If the unit is left unused for a few months, or the unit has been used
predominantly at low power settings, we recommend that the power be increased to
the maximum and the unit left switched on (with the modeling lamp OFF) for at least
30 minutes, to help preserve the life of the capacitors.
5
Flash Settings
Flash Power Output
The flash power output is variable over a four f/stop range (five f/stops) from full power
to 1/16 power in 1/10 f/stop increments. The power is displayed on the LCD screen.
Minimum setting is 2.0 and the maximum is 6.0. Pressing the up and down touch-pad
buttons under the LCD changes the value by 0.1 f-stop (a total of 40 values). If the
current value is 5.6 and you want to reduce the power by one stop, set the power to 4.6.
SETTING POWER
6.0 Full Power
5.0 1/2 POWER
4.0 1/4 POWER
3.0 1/8 POWER
2.0 1/16 POWER
6
Loading...