Angler 7262-W-36, 7262-W-60, 7262-W-18 User manual

Whitebox

INSTRUCTIONS

Introduction

Congratulations on your purchase of an Angler Whitebox Octagonal Softbox!

Angler softboxes are designed to control and soften light for your specific photographic
needs. This softbox is compatible with flash (strobe), fluorescent, and LED lighting
sources. Do not use this softbox with “hot” lights such as quartz, tungsten, or HMI
sources.

Angler octagonal softboxes come in 60-inch, 36-inch, and 18-inch sizes. The
Whiteboxes have a matte white interior finish, which softens and diuses the light. Each
softbox has a front diuser, which can be attached using touch fasteners. The diuser
can be removed to produce more intense light with increased contrast. The removable
internal bae will soften and diuse light further when installed in the softbox. A speed
ring (not included) is required to mount the softbox to a light.

The size of the softbox is related to the lighting eect produced — the larger the softbox,
the softer the light. The distance from the softbox to the object being photographed
also aects the quality of light produced — when the softbox is close to the object, the
light will be more intense, with more contrast. When the distance is greater, the light
will be more diused, with less contrast. The removable interior bae will also soften
and diuse light — you can subtract or add a degree of contrast through inserting or
removing the bae.

2

Highlights

For strobe, fluorescent, and LED lights

Matte white interior

Removable, recessed front diuser

Removable inner bae

Fits most brands of speed rings and lights

Accepts optional fabric grids

3

Contents

User Instructions

Folding the background

1. Grasp the background at two adjacent
corners. Lift the backdrop a little. The
backdrop’s own weight will assist the
folding process. Fold the two ends
together. The background will look like a

2. Pass one hand behind the other in an
overlapping motion—right hand to left
hip and vice versa.

3. Sweep the corner that is in front over the
corner closest to you.

4. Continue folding one side over the other
until both align. The background will now
fit in its carry bag.

1

2

3

4

Front diuser

Flex rods (×8)

User manual Carrying case

collapsible background

whitebox

2254-BW-57

INSTRUCTIONS

INSTRUCTIONS

Interior bae

Fabric shell

Spare flex rod (×1)

4

User Instructions

Please follow these instructions carefully
when assembling your Angler softbox.

There are four parts to your softbox:

1. Fabric shell

2. Flex rods

• 18� - Pre shaped

• 36� - Standard

• 60� - Heavy duty

3. Front diuser

4. Removable internal bae

A speed ring (not included) is required to
assemble the Angler softbox and mount it to
a light. Speed rings are available separately.

1

2

3

4

5

Assembling the Whitebox

1. Insert the small tip of a flex rod into the sleeve
along the inner seam of the softbox shell. Slide
the flex rod through the sleeve until the tip fits
into the end of the sleeve in the front corner
of the softbox. The large tip is now at the rear
of the softbox shell. Repeat this step with the
remaining flex rods.

2. With the speed ring’s reflector mount facing
away from the softbox, insert the end of a flex
rod into a rod hole in the speed ring.

1

2

3. Locate the flex rod directly opposite the first
flex rod installed. Insert the second rod into the
corresponding rod hole in the speed ring, which
is directly opposite the first rod hole used. Flex
the rod gently but firmly until it is securely
seated in the speed ring.

4. Insert the third and fourth flex rods into the
speed ring in the same manner. As each flex rod
is inserted, flex it gently but firmly into position
until each rod is securely seated in the speed
ring.

6

3

4

5. Continue in the same manner, always working
in opposite pairs.

NOTE: The second pair of flex rods installed
should be at a 90° orientation from the first pair so
that a square framework is established.

6. Fold the flaps of the softbox shell over the
speed ring and press down on the touch
fasteners to close the back of the softbox.

7. If you are using the internal bae, attach it to
the interior now, using the straps with snaps
that are built into the softbox.

8. Attach the front diuser to the front of the
softbox using the touch fastener, making sure
the diuser is in contact with the softbox all the
way around its perimeter so no direct light can
escape.

9. With your light unit’s power o, mount the
speed ring to the light unit according to its
manufacturer’s instructions.

6

7

8

9

7

Using an optional grid

An optional grid provides more control over
the light of your softbox by producing a
narrower beam of light than the softbox
alone.

1. Be sure to install the softbox front
diuser at the rear edge of the softbox
touch-fastener strip.

2. Press the grid’s touch fastener firmly
against the softbox’s touch-fastener strip
as smoothly as possible along the length
of one side.

3. Repeat for the remaining sides of the
grid, attaching sides in opposite pairs.

1

2

8

Disassembling the softbox

1. Turn o the power to your light head and disconnect the power
cord from the power supply.

2. Allow time for the light unit, flex rods, and speed ring to cool o
before proceeding.

3. Unmount the softbox assembly from the light head.

4. Pull the flex rods out of the speed ring using the same opposite
rod pattern used in assembly.

5. You can leave the the flex rods, inner bae and front diuser
in place if you wish. The softbox will roll up for storage with its
diuser and inner bae in place.

9

Warnings

Please read and follow these instructions and keep this manual in a safe place.

Keep this unit away from water and any flammable gas or liquid.

Handle this unit with care.

Keep this unit away from children.

Use parts provided by the manufacturer only.

Make sure this item is intact and that no parts are missing.

All photos in this manual are for illustrative purposes only.

10

One-Year Limited Warranty

ANGLER

A Gradus Group

Brand

TM

This Angler product is warranted to the original purchaser to be free from defects in materials and
workmanship under normal consumer use for a period of one (1) year from the original purchase date
or thirty (30) days after replacement, whichever occurs later. The warranty provider’s responsibility
with respect to this limited warranty shall be limited solely to repair or replacement, at the provider’s
discretion, of any product that fails during normal use of this product in its intended manner and in
its intended environment. Inoperability of the product or part(s) shall be determined by the warranty
provider. If the product has been discontinued, the warranty provider reserves the right to replace it
with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse,
improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY
PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you
with specific legal rights, and you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Angler Customer Service Department to obtain a return
merchandise authorization (“RMA”) number, and return the defective product to Angler along with
the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own
risk and expense.

For more information or to arrange service, visit www.anglerlights.com or call Customer Service at
212-594-2353.

Product warranty provided by the Gradus Group.
www.gradusgroup.com

Angler is a registered trademark of the Gradus Group.

© 2015 Gradus Group LLC. All Rights Reserved.

GG1

11

anglerlights.com