Anest Iwata LPH101-P User Manual

INSTRUCTION MANUAL

Low Pressure Spray gun High Volume Low Pressure

LPH-101

Important

This man ual contains IMP ORTANT WA RNINGS and INSTRUCTIONS.

Equipment in this manual is exclusively for painting purposes.
Do not use for other purposes.
The operator shall be fully conversant with the requirements stated in this

instruction manual including important warnings, cautions and operation and
correct handling.

Read and understand the instruction manual, before use and retain for

reference.

Be sure to observe warnings and cautio ns in this ins truction manual.
If not, it can cause paint ejection and se rious bodil y injury by drawing organic solvent.
Be sure to observe following marked items which are especially i mportant .

Important

Indicates a potentially hazardous situation which, if no t avoided, m ay result in serious injury or loss of life.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or property
damage.

Indicates notes which we ask you to observe. The safety precautions in this instruction manual are the minimum
necessary conditions. Follow national and local regulations regarding fire prevention, electricity and safety as well as
your own company regulations.

和文取説は、裏面にあります

This Anest-iwata spray gun kit complies to ATEX
regulations 94/9/EC,
Protection level ：

X marking ：

Ⅱ2 G X，Suitable for use in Zones 1 and 2.
Any static electricity discharge from the spray gu n

is to be diverted to the grounded th e conduc tive
air hose as stipulated.

■

Important specifications

Max. Pressure
Noise level

Spray condition Recommended
Measuring point

Max. T emperature

Atmosphere
Air・Fluid ５℃～４３℃

■

Main specifications

Model

LPH-101-122P Pressure 1.2 (0.047) G2

※1. Atomizing air pressure means air pr essure at gun i nlet when t rigger is pulle d and air flow s．

０．６８ ＭＰａ / ６．８ ｂａｒ / ９８ ＰＳＩ
７８．７ ｄ Ｂ （Ａ）

1m backwards from gun,１．６ m height

５℃～４０℃

Type of

feed

Nozzle

orifice

φmm (in)

Air cap

set

Mark

※1 Atomizing

air pressure

MPa (bar /PSI)

0.34 (3.5/19.8)

Recommended condition

Air pressure

inside air cap

MPa (bar/PSI)

0.07 (0.7/10)

Fluid output

ml/min

350 530 (18.7) 270 (10.6)

Air

consumption

l/min (cfm)

Pattern width

mm (in)

Air &fluid

connection

1/4(Air)

1/4(Fluid)

Mass

g (lbs)

295

（0.65）

－ 1 －

■

Safety precautions

Fire and explosion

1. Spark and open flames are strictly prohibited.

Paints can be highly flammable and can cause fire.
Avoid any ignition sources such as smoking, open flames, electrical goods, etc.

2. Never use the following HALGOGENATED HYDROCARBON SOLVENTS

which can cause cracks or dissolution on gun body (aluminum) by chemical reaction.

・unsuitable solvents：methyl chloride, dichloromethane, 1.2-dichloroethane,carbon tetrachloride,

trichloroethylene, 1.1.1-trichloroethane

（Be sure that all fluids and solvents are compatible with gun parts.

We are ready to supply a material list used in the product）

3. Securely ground spray gun by using air hose with built-in g round wire.
Ground wire : Less than １MΩ. Check the earth stability periodically.

If not, insufficient grounding can cause fire and explosion due to static electric sparking.

Improper use of equipment

1. Never point gun toward people or animal.

If done, it can cause inflammation of eyes and skin or bodily injury .

2. Never exceed maximum operating pressure and

3. Be sure to release air and fluid pressures before cleaning, disassembling or servicing.

If not, remaining pressure can cause bodily injury due to improper operation or scattering cleaning liquid.
In order to release pressure, first stop supply of compressed air, fluid and thin ner to spray gun.
Then remove trigger toward you.

4. Tip of fluid needle set has a sharp point. .

Do not touch the tip of fluid needle during maintenance for the protection of the human body .

maximum operating Temperature.

Protection of human body

1．Use in a well-ventilated site by using spray boot h.

If not, poor ventilation can cause organic solvent poisoning and catch fire.

2．Always wear protective gear （safety glasses, mask, gloves）.

If not, cleaning liquid, etc., can cause inflammation of eyes and skin.
If you feel something wrong with eyes or skin, immediately see a doctor.

3．Wear earplugs if necessary.

Noise level can exceed ８５ｄＢ(A), depending on operating conditions and painting site

4．If operators pull the trigger many times during operation, i t may cause carpal tunnel sy ndrome.
Be sure to take a rest if you feel tired.

Other precautions

1．Never alter this spray gun.

If done, it can cause insufficient performance and failure.

2．Enter working areas of othe r equipment (robots, reci procators, etc.) after m achines are turned off.

If not, contact with them can cause injury .

3．Never spray foods or chemicals through this gun.

If done, it can cause accident by corrosion of fluid passages or adversely affect health by mixed foreign matter .

4．If something goes wrong, immediately stop ope ration and find the c ause. Do not use again until you have solved the problem.

■

How to connect

-Use clean air filtered through air dryer and air filter. ・・・If not, dirty air can cause painting failure.

-If you use this gun for the first time after purchasing, clean flui d passages spraying thinner and remove rus t preventive oil.

If not, remaining preventive oil can cause painting failure such as fish eyes.

-Firmly fix hose or container to spray gun.･･･If not, di sconnection of hose and drop of container can cause bodily injury.

Job1. Connect an air hose to air nipple tightly.
Job2. Connect a fluid hose or container to fluid nipp le tightly.
Job3. Flush the gun fluid passage with a compatible solvent.
Job4. Pour paint into container, test spray and adjust fluid output as we ll as pattern width

－ 2 －