Andobil Technology CDRZ32 user manual
C2
WIRELESS CHARGER
Please read this Operation Instruction carefully and keep
it properly before using this product.
Thank you for purchasing and using this product!
In order to bring you a better experience, read this manual
and also please refer to your mobile phone or electronic
product manual.
Product specifications
Product name
Model
Size
Input
Power
Charging induction
distance
Net weight
Applicable model
Product list
The parameters above are derived from the laboratory
of ANDOBIL, The actual parameter would be different
because of products or other factors. The image shown
here is indicative only.
Wireless charger
CDRZ32
Diameter≈99mm, Thickness≈13mm
5V 2A, 9V 2A, 12V 1.5A
15W(Max)
(4~6)mm
≈138g
The Qi standard of iPhone, Samsung,
LG, Moto and other whole series will
support the wireless charging models
Wireless charger ×1, Type-C data
line ×1, Instruction book ×1
Product overview Instructions
Charging induction distance: the distance between the inner
induction coil of the handset and the inner inductance coil of
the wireless charger is (4-6) mm, and the mobile phone avoids
using a thicker mobile phone shell when using.
Internal magnetic induction coil of cellphone
Phone
Wireless charger
Internal magnetic induction
coil of Wireless charger
Sensor zone
Indicator light
Type-C input port
(4 - 6)mm
1. When the wireless charger is power-on, the blue light
will flash for 2 seconds and go out; the charger goes
into standby;
2. Put mobile phone in the induction zone; blue light will
stay on to indicate the phone is charging;
3. When the wireless charger senses metal objects other
than mobile phones, blue light will keep flashing and
the charger will turn on charging protection.
Note: the charging equipment must meet the Qi standard
to be used.
Notes
1. Do not press hard or crash the product.
2. Do not disassemble or reassemble.
3. Do not put the product near the fire or into the fire,
water.
4. Do not use wireless charger in severe high temperature
and humidity or corrosion to avoid leakage.
5. Do not place too close to a magnetic card(id card and
credit card)with a magnetic strip or chip to avoid the
failure of the magnetism.
6. Do not put metal plate or metal shell on the charger.
7. Please keep the distance between the implanted
medical device (pacemakers, implants, etc.) and the
wireless charger at least 20cm to avoid potential
interference to the medical device.
8. Please keep the charger away from water or other
liquids.
9. Make sure not connect the power if you need to clean
the wireless charger.
10. Please don't use it as a toy for children.
11. The ambient temperature shall be kept between 0-45℃.
FCC Statement
This device complies with part 15 and part 18 of the FCC Rules.
Operation is Subject To the following two conditions:
(1) This device may not cause harmful interference, and (2) this
devicemust accept any interference received, including interference
that may cause undesired operation. Changes or modifications not
explicitly approved by the partyresponsible for compliance could
void the user's authority tooperate this equipment.
Note: this equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 and part 18 of
the FCC Rules. These limits are designed to providereasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and canradiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference toradio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged totry to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
The equipment complies with FCC radiation
exposure limits
During the operation of device a distance of 15 cm
surrounding the
the device must
This device complies with Part 18 of the FCC Rules. This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
●Increase the separation between the equipment and any
other radio device.
set forth for an uncontrolled environment.
device and 20 cm above the top surface of
be respected.
●Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Warranty Card
Customer Name:
Phone Number:
Product Name:
Date of Purchase:
Address:
Notes:
WWW.ANDOBIL.COM
Email: support@andobil.com
Add: 322, Bldg. 7, Pengsheng Village, No.39 Bagua 1 Rd.,
Pengsheng CMNY, Yuanling St Futian Dist., Shenzhen
CHINA
Shenzhen Andobil Technology Co., Ltd.
Andobil is the trademark registered in U.S and other
countries. All rights reserved.
MADE IN CHINA
Loading...