Andis Company GTO, GO User Manual 2

USE AND CARE

MODEL GO, GTO

Literature Packet #04964

Item pictured may differ from actual product

El artículo ilustrado puede diferir del producto real

Il est possible que l’article sur la photo soit différent du produit réel

ENGLISH

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should always
be followed, including the following: Read all instructions before

using the Andis trimmer.

DANGER:

1. Do not reach for an appliance that has fallen into water. Unplug
immediately.

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can fall or be pulled into a
tub or sink. Do not place in or drop into water or other liquid.

4. Always unplug this appliance from the electrical outlet
immediately after using.

5. Unplug this appliance before cleaning, removing or assembling parts.

To reduce the risk of electric shock:

WARNING: To reduce the risk of burns, fire electric shock,

or injury to persons:

1. An appliance should never be left unattended when plugged in.

2. Close supervision is necessary when this appliance is used by, on
or near children or individuals with certain disabilities.

3. Use this appliance only for its intended use as described in this
manual. Do not use attachments not recommended by Andis.

4. Never operate this appliance if it has a damaged cord or plug, if it
is not working properly, if it has been dropped or damaged, or
dropped into water. Return the appliance to an Andis Authorized
Service Station for examination and repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Do not use outdoors or operate where aerosol (spray) products
are being used or where oxygen is being administered.

8. Do not use this appliance with a damaged or broken blade or
comb, as injury to the skin may occur.

9. To disconnect turn control to “off” then remove plug from outlet.

10. If this trimmer has means for grounding, connect to a properly
grounded outlet only. See Grounding Instructions.

2

SAVE THESE INSTRUCTIONS

THIS PRODUCT INTENDED FOR PROFESSIONAL USE

These instructions only apply to trimmers with a 2-prong plug:

To reduce the risk of electric shock, this appliance has a polarized plug (one
blade is wider than the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to install the proper outlet. Do not
change the plug in any way.

GROUNDING INSTRUCTIONS

These instructions only apply to trimmers with a 3-prong plug:

This appliance should be grounded. In the event of an electrical short circuit,
grounding reduces the risk of electric shock by providing an escape wire
for the electric current. This appliance is equipped with a cord having a
grounding wire with an appropriate grounding plug. The plug must be
plugged into an outlet that is properly installed and grounded in accordance
with all local codes and ordinances.

DANGER: Improper use of the grounding plug can result in a risk of

electric shock. If repair or replacement of the cord or plug is necessary, do
not connect the grounding wire to either flat-blade terminal. The wire with
insulation having an outer surface that is green with or without yellow stripes
is the grounding wire. Check with a qualified electrician or serviceman if the
grounding instructions are not completely understood, or if in doubt as to
whether the appliance is properly grounded. Do not modify the plug provided;
if it will not fit the outlet, have the proper outlet installed by a qualified
electrician. This appliance is for use on a nominal 120-volt circuit, and has a
grounding plug (Figure A). A temporary adapter (Figures B & C) may be used
to connect this plug to a 2-pole receptacle (Figure B) if a properly grounded
outlet is not available. The temporary adapter should be used only until a
properly grounded outlet (Figure A) can be installed by a qualified electrician.
The green colored rigid ear, lug, or the like extending from the adapter must
be connected to a permanent ground such as a properly grounded outlet-box
cover. Whenever the adapter is used, it must be held in place by a metal
screw.

3

Grounded

2-Pole

Receptacle

Adapter

Tab for

Grounding Screw

Adapter

Metallic

Screw

Tab for

Grounding Screw

Adapter

Outlet

Adapter

Grounded

Lower

Blade

Pin

Blade

Grounded
Outlet Box

FIGURE A

FIGURE D

Upper
Blade

Hole in
Upper
Blade

FIGURE G

Metallic

Screw

Blade Screws

Hair

Guard

2-Pole

Receptacle

FIGURE B

Oil

FIGURE E

Nylon
Roller
(Ball)

Adapter

Grounding Screw

FIGURE C

Blade Screws

FIGURE F

FIGURE H

Tab for

Lower blade
Upper blade

4

FIGURE I

OPERATING INSTRUCTIONS

Please read the following instructions before using your new Andis trimmer.
Give it the care that a fine precision built instrument deserves and it will give
you years of service. Before starting trimmer remove blade guard (some
models may not have a blade guard). Plug cord into electrical outlet, operate
at 120 volt, 60 cycle AC electrical current or as noted on the unit. To start
trimmer move switch button to on position, to stop, move switch button back
to original position. After using your Andis trimmer, rewrap cord and store in
a safe place.

USER MAINTENANCE

The internal mechanism of your trimmer has been permanently lubricated at
the factory. Other than the recommended maintenance described in this
manual, no other maintenance should be performed, except by Andis
Company or an Andis Authorized Service Station. To find an Andis Authorized
Service Station near you log on to www.andis.com or contact our customer
service department: 1-800-558-9441 (U.S.) or 1-800-335-4093 (Canada).

CARE AND SERVICING OF YOUR ANDIS TRIMMER BLADES

Blades should be oiled before, during, and after each use. If your trimmer
blades leave streaks or slows down, it’s a sure sign blades need oil. The
trimmer should be held in a position shown (Figure D) to prevent oil from
getting into motor. Place a few drops of Andis Clipper Oil on the front and
side of the cutter blades (Figure E). Wipe excess oil off blades with a soft dry
cloth. Spray lubricants contain insufficient oil for good lubrication, but are an
excellent trimmer coolant. Always replace broken or nicked blades to prevent
injury. You can clean the excess hair from your blades by using a small brush
or worn out tooth brush. To clean the blades we suggest to immerse the
blades only into a shallow pan of Andis Clipper Oil, while the trimmer is
running. Any excess hair and dirt that has accumulated between the blades
should come out. After cleaning, turn your trimmer off and dry blades with a
dry cloth and start clipping again.

REPLACEMENT (REMOVAL) OF BLADE SET

NOTE: If you are familiar with replacing and adjusting Andis GO and GTO

trimmer blades, please read the following blade replacement instructions.

5

If you are not familiar with this procedure, please return trimmer to your
supplier or an Andis Authorized Service Station for blade replacement and
adjustment.

To remove blade set from your trimmer, unplug your trimmer from the
electrical outlet. Turn the trimmer upside down so the teeth of blades are
facing down. You may wish to set the trimmer on a flat surface while
performing these operations. Unscrew the two blade screws (Figure F).
Remove blade set from trimmer. To install your new trimmer blade set, align
hole in upper blade (smaller of the two blades) and center over nylon roller
(ball) of the trimmer’s tension spring (Figure G). Align screw holes of lower
blade (larger of the two blades) to armature screw holes. While holding blade
in place, replace blade screws; do not tighten down completely. Turn trimmer
over and align the blade set parallel to the trimmer’s upper housing.

IMPORTANT: Check blade alignment, making sure the teeth of the upper
blade rest slightly below the upper edge of teeth on lower blade (Figure H).
Failure to check the position of blade may cause cutting or scratching of your
client’s skin when trimming. Tighten down blade screws firmly. If after
turning on the trimmer you notice the hair guard is hitting the upper blade
(Figure I) loosen hair guard screws slightly and adjust hair guard away from
the upper blade approximately 1/32". Tighten down hair guard screws.

FACTORY REPAIR SERVICE

When the blades of your Andis trimmer become dull after repeated use,
it is advised to purchase a new set of blades available through your Andis
Supplier or through an Andis Authorized Service Station. If you wish your
trimmer to be serviced as well, it should be carefully packed and mailed
either Parcel Post Insured, or U.P.S. to any Andis Authorized Service Station.
To find an Andis Authorized Service Station near you log on to www.andis.
com or contact our customer service department: 1-800-558-9441 (U.S.) or
1-800-335-4093 (Canada).

Caution: Never handle your Andis trimmer while you are operating a water faucet,
and never hold your clipper under a water faucet or in water. There is danger of
electrical shock and damage to your clipper. Andis Company will not be

responsible in case of injury due to this carelessness.

6